KAWASAKI VULCAN 900 SLASH CUT STAGGEREDS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 02-05-2012

download
1. Attach mounting bracket 440-P to frame using two stock fl ange head bolts used on stock upper bracket (Figures 1 and 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through (Figure 3). 3. Lay front header, and rear header into their head heat shields and muffl er body heat shields. 4. Install #20 hose clamps (supplied) on heat shields and #36 (supplied) on muffl er body heat shields by feeding tail end of clamps into heat shield clips (fi gure 3). Take note of clamp screw head direction (Figure 4). Screw heads must be accessible when system is installed on motorcycle for adjustment purposes. NOTE: Do not tighten at this time. 5. Using stock fl ange nuts, carefully install head pipes into exhaust ports. Assistance may be required. NOTE: Do not tighten at this time. 6. Slide nut plates inside bracket that is welded to backside of muffl er bodies (Figure 5). While holding nut plates in place, attach muffl er bodies to mounting bracket 440-P using two 5/16″x 5/8″ fl ange head bolts (supplied). Leave them loose at this time. 7. Align muffl er bodies so they are level and parallel when viewing from the right side of the bike. Tighten cylinder port exhaust fl ange nuts on front and rear cylinders. 8. Tighten the fl ange bolts on both muffl ers. 9. Tighten all heat shield clamps. 10. Check for adequate clearance of all exhaust system components and motorcycle accessories prone to heat damage. NOTE: For models with fl oorboards, two Spacer washers are supplied to space out the fl oorboard bracket enough to allow the fl oorboard to fold up without hitting the heat shield. 11. Be sure to tighten all hardware before starting your motorcycle. 12. After installation and before starting motorcycle, completely clean pipes and muffl ers with cleaning solvent and a clean, soft cloth that will not leave a residue. NOTE: Any residue, oil, or fi ngerprints will stain the chrome when the metal heats up

Incoming search terms:

Harley Davidson AIR INTAKE SYSTEM INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-04-2012

download
1. Preparing Vehicle a. Make sure vehicle is parked on level surface. b. Set parking brake. c. If engine has run in the past two hours, let it cool down. d. Disconnect negative battery terminal. e. Do not discard stock components after removal of the factory system. 2. Removal of stock system a. Stock air box configuration system. b. Release the four clips on the air box. c. Loosen the hose clamp on the turbo inlet pipe. d. Vehicle equipped with MAF sensor. Unplug the mass air flow (MAF) sensor. 4 d) Clamp removal. e. On vehicles equipped with IAT, unplug the IAT sensor and remove from the housing. f. Pull the air filter status meter from the grommet. g. Remove the rear section of the intake system. h. Remove the remaining stock air box system. 5 3. Installation of AEM® intake system. a. When installing the intake system, do not completely tighten the hose clamps or mounting hardware until instructed to do so. i. Use the supplied torx key to remove the MAF sensor. Save screws for later use. b. Install the supplied coupler as shown. c. Place the aluminum stand in the plastic member as shown.

Incoming search terms:

HONDA VTX 1300 Retro BIG SHOTS EXHAUST SYSTEM INSTALLATION

0

Filed Under (Honda) by admin on 07-12-2011

download
Check condition of stock exhaust gaskets. Replace if damaged or worn. 2. Install and tighten supplied mounting bracket (stamped
346-P) in the original mounting bar location, using two M10x40 flange bolts, nuts, and washers (supplied) (Figure 1). 3. Install and tighten rectifier using M6x30 flange bolt, nut, and washer combinations (supplied)(Figure 1). 4. Place heat shields on a non-abrasive surface such as a blanket or carpet. Using a felt tip marker, mark the outside surface of front and rear heat shields with the location of the mounting clips welded inside(Figure 2). 5. Install each heat shield over its respective head pipe (Figure 3). 6. Install each hose clamp by feeding tail end of clamp into heat shield clip. Take note of clamp screw head direction (Figure 2 & 4). Screw head should be ccessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas. Note: Prior to tightening hose clamps, align end caps so that slash ends are even.

HONDA AERO 750 CRUZER EXHAUST SYSTEM REMOVAL And INSTALLATION

0

Filed Under (Honda) by admin on 18-11-2011

download
Install mounting bracket (stamped 363-P) in the original muffler mounting position, using two 10mm bolts and
one 10mm nut. (supplied)(Refer to figure 2). 2. Mark outside surface of front and rear heat shields with location of mounting clips that are welded to the inside.(Refer to figure 3).Place each heat shield on a non-abrasive surface such as a blanket or carpet. Position each head pipe/muffler over its respective heat shield. (Refer to figure 4).
3. Feed tail end of each hose clamp through each mounting clip welded to back side of front and rear heat shields. Take note of clamp hex screw head direction. (Clamp head direction is critical for adjustment when system is installed on bike.) Wrap each clamp around back side of head pipe threading tail end into clamp head. (Refer to figure 3 & 4).
4. Install front head pipe/muffler using stock flange nuts. Slide dog bone shaped nutplate (supplied) inside
bracket welded to backside of muffler. Attach muffler to mounting bracket 363-P using (supplied) 5/16” flange
bolts engaging dog bone nutplate. Leave head pipe/muffler assembly loose at this time (Refer to figure 4). Repeat this step with the rear head pipe.5. Align mufflers so they are parallel when viewing from right side of the motorcycle. Tighten 5/16” flange bolts securing upper and lower muffler positions.. Tighten cylinder exhaust port flange nuts securing head pipes to cylinder heads. 7. Adjust heat shields so they meet front of muffler taper. (Refer to figure 6). Tighten all hose clamps securing heat shield locations. NOTE: Heat shields should cover muffler/head pipe weld joint.

HONDA SHADOW AERO 750 STRAIGHTSHOT HS EXHAUST SYSTEM

0

Filed Under (Honda) by admin on 03-11-2011

download
Install mounting bracket (stamped 359-P) in the original bracket mounting position, using two 10mm bolts and
one 10mm nut (supplied)(Figure 2). 2. Remove head pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark the outside edge of each heat shield to show location of hose clamp mounting clips (Figure 3). 3. Slide flanges onto head pipes and lay head pipes into
heat shields. Loosely install hose clamps by feeding tail end of clamp into heat shield clips (Figure 3). Take note of screw head direction (Figure 4). Screw head should be accessible when system is installed on motorcycle for adjustment purposes. Use #20 hose clamps for head pipe areas and #28 hose clamps for muffler areas.
4. Using stock nuts, carefully install head pipes into exhaust ports (Assistance may be required). NOTE: Do not tighten at this time.

HARLEY DAVIDSON SOFTAIL OIL COOLER KIT WITH CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models

Incoming search terms:

HONDA GL1200 fork seals Removal And Installation Manual

0

Filed Under (Honda) by admin on 27-02-2011

download
subsequent seal failure it can cause, is to cover or “shield” the tubes in some manner that goes beyond the normal protection offered by dust seals. My old CB200T has the traditional, accordion-rubber “gaiters” over the shock tubes, and the seals have failed only once in 12 years, at 80,000 miles. That’s why you still see gaiters on virtually every off-road bike made. But somewhere along the line “fashion” and “design” overcame common sense, and we all started insisting on street bikes with modern-looking, totally exposed, polished fork tubes. Gaiters were dropped almost entirely, determined to be much too old-fashioned-looking, or as contributing in some miniscule manner to fork “stiction.” Maybe so—but they worked. Some riders, wise to the ways of seal failure, have developed “home remedies” to protect their forks. Among the ones I’ve seen are sections of rubber hose attached to fork housings with hose clamps, or the more attractive addition of vinyl “wrap-arounds” that velcro around the tubes and slide up and down with the forks. Some of these are even color-matched to the bikes. I used to own a Honda GL1200 that needed the fork seals replaced at 21,000 miles, 43,000 miles, and 62,000 miles. Then I covered the exposed upper tubes with vinyl “sliders,” and never had to replace the seals again. The bike’s current owner now has the odometer up to 124,000 miles, and the seals are still holding. Honda must have gotten wise to this, because the GL1500 models came with plastic “fork shields” built right onto the front fender. Even though they don’t quite cover the entire exposed area of the tubes

Incoming search terms:

KAWASAKI VULCAN 800 STRAIGHT SHOT EXHAUST SYSTEM INSTALATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the two header flange nuts from the front and rear head pipes. 2. Remove the acorn nut located under the rear muffler. 3. Remove the two allen bolts located under the front muffler. 4. Remove the stock exhaust system from the motorcycle and set it aside. 5. Remove the two hex head bolts that attach the stock muffler mounting bracket to the frame of the motorcycle. Remove the muffler bracket and set it aside. 6. Remove the two rubber grommets and spacers from the stock muffler and the one grommet and spacer from the muffler mounting bracket. Set them aside with the the two mounting bolts, they will be reused during installation. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install a chrome header flange onto the front and rear head pipes. 3. Install the heat shield to the front head pipe using the two hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe with the heat shield attached, to the front cylinder using the stock nuts. Leave them loose at this time. 5. Install the rear head pipe, with the heat shield attached, to the rear cylinder using the stock nuts. Leave them loose at this time. 6. Install the stock rubbber grommets and spacers into the three large holes on the V&H mounting bar (See figure 1). 7. Slide one dog bone shaped nut plate under the bracket that is welded to each muffler. 8. Slide a chrome muffler clamp (supplied) onto the inlet end of each muffler. Install a 5/16″ x 1 1/4″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Do this to each muffler but leave the clamp loose at this time. 9. Install one muffler to the four hole bracket welded to the V&H mounting bar using the two 5/16″ flange bolts (supplied) and leave them loose. (See figure 1) 10. Slip the muffler and mounting bar assembly onto the front head pipe while aligning the grommet holes in the mounting bar with the holes in the frame.

Incoming search terms:

HONDA VT750 EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 24-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove the header flange nuts at the exhaust port on the front and rear head pipes. 2. Remove the two 8mm nuts from the muffler mounting bracket, while supporting the entire exhaust system. Lower the system down and set it aside. Note: Save the stock hardware for reuse. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 2. Install the muffler mounting bracket (stamped 268) to the original muffler mounting point, using the two stock 8mm nuts. Refer to figure 1. 3. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of the front muffler. 4. Install the front head pipe to the cylinder head using the stock nuts. Attach the muffler to the mounting bracket using the two 5/16″ flange bolts (supplied). Leave the nuts and bolts loose at this time. 5. Repeat steps 2 and 3 with the rear header. 6. Align the mufflers so they are parallel when viewing from the right hand side of the motorcycle. Tighten all the hardware evenly. 7. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. 8. Rotate the hose clamps on both heat shields so they are accessible with a screw driver and tighten each of them evenly. The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Note : The heat shields should cover the weld on the muffler. 9. Be sure to remove any dirt, oil or finger prints from the entire exhaust system before starting the motorcycle.

HARLEY DAVIDSON SOFTAIL FATBOY STRAIGHTSHOT HS SLIP ON INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-12-2010

download
1. Remove the heat shield from the rear head pipe and the back heat shield (“Z” Shaped) off the lower head pipe. NOTE: Loosen the front heat shield hose clamp closest to this shield to facilitate its removal. 2. Loosen the clamps holding the muffl ers onto the head pipes. 3. Remove the 1/2″ bolts holding muffl ers onto support bar. 4. Slide both muffl ers towards the rear until they are free from the head pipes. NOTE: Assistance and the use of a penetrating lubricant may be required. 5. Remove the stock exhaust clamps from the nose of each muffl er (these will be re-used when installing the new system). QUIET BAFFLE FUELPAK VANCE & HINES EXHAUST SYSTEM INSTALLATION WHEN YOU KNOW THE DIFFERENCE 1. Using the 5/16″ x 3/4″ hex head bolts and washers (supplied) secure the mounting bracket (stamped 419-P)(supplied) to the stock muffl er support bar. NOTE: The bracket should be mounted with the notch facing the front of the motorcycle (Figure 1). 2. Remove muffl ers and heat shields from their protective packaging and place them on a non-abrasive surface such as a blanket, towel or carpet. 3. Carefully lay a muffl er assembly into each straight heat shield and loosely install the hose clamps (supplied) by feeding the tail end of the clamp into the heat shield clips. Note the direction of the screw heads with relation to the muffl er location (Figure 2). 4. Slide stock exhaust clamps onto the nose of each muffl er body. NOTE: Orient the clamp to enable access for tightening the nut after installation. 5. Slide upper muffl er assembly (with heat shield) onto the upper head pipe. Insert nut plate (supplied) into the bracket welded to the muffl er body (Figure 3) and secure to the mounting bracket using the 5/16″ x 5/8″ fl ange head bolts (supplied). 6. Repeat step 5 placing the lower muffl er assembly on the lower head

Incoming search terms:

Incoming search terms: