Kawasaki 900 / 1100 Engine Removal and Installation

0

Filed Under (Kawasaki) by admin on 01-05-2012

download
1.1 (Above) Remove the two retaining straps, disconnect the battery and remove it from the hull. Disconnect the negative (black) cable first, then the positive (red). Step 2 Intake Removal 2.1 (Below) Remove the eight 10mm bolts securing the flame arrestor cover to the base and remove it. 2.2 (Below) Pull out the flame arrestor screens. 2.3 (Below) Remove the six 10mm bolts securing the flame arrestor base and carbs to the manifold and remove the base. 2.4 (Below) Loosen the gas tank cap to relieve pressure. Be sure the fuel switch is turned to the “OFF” position, and be aware of any fuel that may spill from the hoses. Make sure the hull is clear of any gasoline fumes before continuing work, especially with power tools. Remove the pulse lines from the block, and the three oil lines from the carbs. Move the carbs aside in the hull. 2.5 (Below) Remove the 18 10mm nuts from the studs securing the intake manifold to the engine and remove the manifold

Incoming search terms:

Toyota and Lexus Clogged Power Steering Reservoir Filter

0

Filed Under (Toyota Manuals) by admin on 02-10-2011

download
Clogged Power Steering Reservoir Filter – Toyota & Lexus Toyota and Lexus vehicles with power steering. Noise coming from the power steering pump or reduced assist from the power steering system. Noise or reduced assist may be caused by restriction in the power steering fluid reservoir. Most Toyota/Lexus-style reservoirs have a filter screen at the bottom. Over a period of time this filter could get clogged causing the restriction of fluid. Replace any hose that shows signs of cracking or internal deterioration. Thoroughly flush the power steering system; then remove the reservoir for cleaning as follows: 1. Clean the exterior and interior of reservoir with new power steering fluid or suitable solvent. 2. Blow off the filter screen using pressurized air until restriction or clog is removed. 3. Using a flashlight, check to make sure that the filter screen is free of debris. Note: Contamination may be an indication of internal breakdown of hoses, which must be replaced before operating the vehicle. Failure to replace bad hoses could damage both the pump and steering unit. 4. Reinstall reservoir, referring to the service manual for tightening specs and bleeding procedures.

Incoming search terms:

2006 2007 Yamaha R6 Front Brake Line Kit INSTALLATION

0

Filed Under (Yamaha) by admin on 25-05-2011

download
Identify the key components that complete our brake line kit: You should have two (2) hoses, one (1) double banjo bolt, two (2) single banjo bolts, and one (1) zip ties. There are also a total of nine (9) washers. Seven (7) will be used, and two (2) are spares. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Please note there is a plastic shield on the lower triple clamp of most models; we took this piece off to ease installation. Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, 40-degree banjo labeled for right line, washer, 20-degree banjo labeled for left line, washer, master cylinder. Please see picture A for reference! Double banjo bolts must be torqued at 12 FT pounds.

HARLEY DAVIDSON XL STARTER MOTOR COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. Remove exhaust system according to Service Manual instructions. 2. See Figure 1. Remove the outer primary screw shown and retain it for reinstallation. 3. See Service Parts Illustration. Insert the thread cleaning screw (9), through the primary cover and the crankcase until the full screw diameter protrudes through the crankcase. Remove any debris from from the tip of the thread cleaning screw. Remove thread forming screw and discard. NOTE If thread cleaning screw binds in crankcase hole, remove thread cleaning screw and chase threads with 1/4 – 20 tap. 4. Install set screw (8) from outer primary side using the wrench provided. Set screw should extend past the crankcase approximately .375″. 5. With wrench in set screw to prevent rotation, install the backplate over the set screw and fasten with the 1/4-20 nylock nut (5). 6. Reinstall the primary cover screw saved in Step 1. Torque to 80-110 in-lbs (9-12 Nm). 7. Remove the the oil hose clamp from the starter stud. Do not remove the clamp from the hoses. 8. Replace the original equipment starter stud with stud (7) provided. Torque to 39-65 in-lbs (4-7 Nm). 9. Install bracket (2) over stud (7) and fasten with #10-24 nylock nut (6). Rotate bracket until the tab on the bracket rests on starter motor. 10. Install oil hose clamp onto bracket (2) using one of the #10-24 screws (4). Tuck the hoses down as far as possible without contacting the drive belt or kinking the hose. Contacting the drive belt or kinking the hose may cause damage to the hoses or powertrain. 11. Install the cover (1) to the backplate (3) and bracket (2) using four of the #10-24 screws (4) with the wrench provided. The cover should fit inboard of the gear cover and partially on top of the sprocket cover. Start the bracket screw first, then follow with the (3) backplate screws. 12. Reinstall exhaust system according to Service Manual Instructions

HARLEY DAVIDSON SOFTAIL OIL COOLER KIT WITH CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models

Incoming search terms:

2008 Suzuki GSXR 600-750 Super bike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our SUPERBIKE brake line kit: You should have two (2) hoses, one (1) double banjo bolt, and two (2) male adapters with two 1.55mm thick washers. There are also a total of (7) washers. five (5) will be used, and two (2) are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter with the two thick crush washers provided into the calipers with one washer, and torque at 12 to 13 ft pounds. Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 90 degree banjo from left line, washer, 90 banjo from right line, washer and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (For positioning see picture A) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see picture B) . Thread each female end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using (GALFER’S C-CLIP) to bring the lines together about the same level as the lower triple clamp.

2004-2007 HONDA CBR 1000RR Super bike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Make sure to save the nut and bolt that are currently holding the stock lower section of the hoses. (See picture A) Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 40-degree banjo from right line, washer, 40-degree banjo from left line, washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (For positioning see picture B) . Make sure that the 90-degree fittings on each caliper are pointing straight up (see picture C) . Thread each banjo end onto the adapter, and torque to 6 ½ Ft pounds. Please tighten the “C” clips on the fender using the OEM bolts we asked you to save above. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, using the galfer 2line clip to bring the lines together and mounting it to the triple tree will insure proper clearness and routing. (See picture D) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with Galfer DOT 4- brake fluid is recommended.

YAMAHA ROAD STAR HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Place a blanket folded several times over the fuel tank to prevent any damage during the installation of the risers. Loosen the two 19mm riser mounting nuts located on the bottom side of the upper steering head. Pry out the chrome plugs from the heads of the four handlebar top clamp bolts using a knife blade. Loosen the four handlebar top clamp 6mm socket head screws. 2. It will help having a second person to hold the handlebars while you change the risers. Remove the four screws from the clamps and then the clamps. Pull the handlebars up off the risers, pull them back and rest them on top of the blanket. 3. Remove the nuts from the bottom of the risers and remove the risers. Insert the two supplied spacer tubes into the riser mounting holes on the upper steering head. Using the bolts, lock washers and washers supplied install the new risers making the bolts finger tight only. (Take care not to scratch the top surface of the upper steering head while installing the new risers.) 4. Place the handlebars back up onto the new risers. Reinstall the top clamps using the four socket head screws removed earlier. Set the height of the handlebars to the desired position, tighten the front bolts first and then the rear securely. (15-18 ft. lbs. There should be no gap between the riser and clamp at the front side.) Tighten the two riser mounting bolts securely. (20-25 ft. lbs.) 5. Turn the handlebars all the way to the left and then right checking for any pulling or binding of the wires, hoses or cables. Also check that the throttle returns freely on it’s own

2007 Yamaha R1 Front Brake Line Kit Installation instructions

0

Filed Under (Yamaha) by admin on 27-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, 40-degree banjo labeled for right line, washer, 20-degree banjo labeled for left line, washer, master cylinder. Double banjo bolts must be torqued at 12 FT pounds. (See picture A for sequence) Step 5: Route brake lines below the stock lower triple clamp, and zip tie them together. This will ensure your lines stay in position as the steering moves. Also, make sure the lines are secured beneath the steering stabilizer rod. (See picture C) Step 6: Before installing the lines onto the right and left calipers, replace the OEM bracket with the enclosed “C-clip”. Route the hose through the new bracket and thread the single banjo bolts at each caliper using the following sequence: 20-degree banjo, washer, single banjo bolt, washer, thread into caliper. Torque banjo bolts to 12 FT pounds. (See picture B) Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Step 7: Bleed brake system according to owner’s manual, and build appropriate pressure. Keep in mind your master cylinder is equipped with it’s own bleeder nipple. Finish with Galfer DOT-4 brake fluid

HONDA VTX1300, VTX1800 R, C & S MODEL HANDLEBAR RISERS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 27-12-2010

download
1 .Lay a blanket folded several times over the fuel tank to protect it. 2. Notice on the 1800 models that there is a small punch mark on the handlebars located on the right hand, front side of the handlebars where the risers meet the top clamp/speedometer housing. This is to reference the handlebar position when re-assembling. On the 1300 models there is a punch mark on the forward facing side of the clamp, these must be installed the same way. 3. Loosen the two 19mm nuts holding the risers to the upper triple clamp (steering head). 4. Pry out the four chrome caps covering the handlebar bolts. Remove the four handlebar clamp bolts. (6mm allen wrench). While sitting on the motorcycle, pull the handlebars and upper clamp off of the risers. They may be slightly stuck and require some force to get free. Lay the handlebar and/or upper clamp/gauge assembly carefully on the blanket. 5. Remove the 19mm nuts and the risers from the triple clamp. NOTE: Be careful not to scratch the upper triple clamp when installing the new risers. Place the thin flat washers provided into the recess at the top of the riser bolt holes on the triple clamp. Assemble the lock washers provided and then the original flat washers onto the bolts provided. Install the new risers onto the triple clamp and snug the bolts. 6. Re-install the handlebars and upper clamp/gauge assembly. ( Remember the punch marks) Tighten the front bolts first closing the gap at the front, and then tighten the rear bolts. Tighten the two 19mm riser-mounting bolts securely. Check for adequate clearance and proper routing of cables and hoses.

Incoming search terms:

Incoming search terms: