HARLEY DAVIDSON BRAIDED, DUAL DISC, FRONT BRAKE LINE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION 1 is03017 1. Bleed valve cover Figure 1. Brake Caliper Bleed Valve Rubber Cover 2 1 3 is03018 1. Plastic tube 2. Caliper bleeder valve 3. Container Figure 2. Draining Brake Fluid NOTE This instruction sheet covers motorcycle models that use either DOT 4 or DOT 5 Hydraulic Brake Fluid. The owner’s manual -J03109 1 of 2 will indicate which type of br ake fluid should be used on the motorcycle. Read and follow the owner’s manual carefully. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a) D.O.T. 4 brake fluid will damage painted and body panel surfaces it comes in contact with. Always use caution and protect surfaces from spills whenever brake work is performed. Failure to comply can result in cosmetic damage. (00239b) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 1. See the service manual and disconnect negative (-) battery cable or remove the main fuse. Save the seat hardware for installation. 2. See Figure 2. Open bleeder nipple cap on front brake caliper. Install end of a length of plastic tubing over caliper bleeder valve (1), while placing free end in a suitable container. Open bleeder valve approximately 1/2 turn. Pump brake lever to drain brake fluid. Repeat step for the other caliper. 3. Remove bolt and two sealing washers to disconnect brake line fitting from master cylinder. Save bolt and discard washers.

HARLEY DAVIDSON CHROME REAR BRAKE RESERVOIR COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
INSTALLATION 1. Remove and discard the screw and washer holding the rear brake master cylinder reservoir to the motorcycle frame. 2. See the Figure 1. Obtain the chrome screw (2) and washer (3) from the kit. Place the washer onto the screw threads. 3. Position the chrome rear brake reservoir cover (1) over the reservoir, lining up the holes. Fasten with the chrome screw and washer using the T27 TORX® key (6) from the kit. Tighten securely. 4. Slowly unscrew the original reservoir cap. Note the orientation of the reservoir gasket and the gasket collar, which may come off with the cap. Discard the original reservoir cap only. Set the gasket and collar aside for re-installation. Direct contact of D.O.T. 5 brake fluid with eyes can cause eye irritation, swelling, and redness. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 5 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00144a) 5. Refer to the Owner’s Manual and follow the procedure to check the brake fluid level. Fill as needed with DOT 5 SILICONE HYDRAULIC BRAKE FLUID. Do not reuse old fluid. Only use DOT 5 hydraulic brake fluid from a sealed container. 6. Set the reservoir gasket back onto the lip of the reservoir and position the gasket collar onto the gasket. 7. Carefully position the new chrome cap (4) over the reservoir and screw it on. Tighten securely. 8. Clean the indented top surface of the new cap with a 50- 50 mixture of isopropyl alcohol and water and let it dry. 9. Peel the paper backing from the Bar and Shield emblem (5). Turn the emblem to the desired orientation and press it firmly into place on the top of the chrome cap. After repairing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury.

Incoming search terms:

2008 FLT Police Models Service Manual Supplement

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ITEM SERVICED 14-21 ft-lbs (19.0-28.5 Nm) Drain plug torque Engine oil and filter 4 qt. (3.8 L) Oil capacity Hand tighten 1/2-3/4 turn after gasket contact Filter 63798-99A Chrome filter part number 63731-99A Black filter part number FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity Primary chain lubricant Wet: 38 oz. (1124 ml) Dry: 45 oz. (1331 ml) 14-21 ft-lbs (19.0-28.5 Nm) Primary chaincase drain plug torque 1/2-1 turn Adjuster screw free play Clutch adjustment 72-120 in-lbs (8.1-13.6 Nm) Adjuster screw locknut torque 1/16-1/8 in. (1.6-3.2 mm) Free play at hand lever 84-108 in-lbs (9.5-12.2 Nm) Clutch inspection cover torque Dipstick at FULL with motorcycle on jiffy stand and filler plug resting on threads. Lubricant level Transmission lubricant FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity 32 oz (0.95 liters) 14-21 ft-lbs (19.0-28.5 Nm) Transmission drain plug torque 25-75 in-lbs (2.8-8.5 Nm) Transmission filler plug/dipstick torque Front: 36 psi (248 kPA) Pressure: solo rider Tire pressure and wear Rear: 36-40 psi (248-276 kPA) Replace if less than 1/32 in. (0.8 mm) of tread pattern Wear 55 in-lbs (6.2 Nm) minimum Spoke nipple torque Wheel spokes 99953-99A (12 oz.) D.O.T. 4 hydraulic brake fluid part number Brake fluid level Front: 0.20 in. (5.0 mm) Fluid level (from top of master cylinder reservoir) Rear: 0.26 in. (6.5 mm) Front: 7-10 in-lbs (0.8-1.1 Nm) Master cylinder reservoir cover screw torque Rear: 12-15 in-lbs (1.4-1.7 Nm) 0.016 in. (0.4 mm) Minimum brake pad thickness Brake pads and discs 75-102 in-lbs (8.5.-11.5 Nm) Brake caliper pad pin torque Front: 0.18 in. (4.5 mm) Minimum brake disc thickness Rear: 0.25 in. (6.3 mm) 0.008 in. (0.2 mm) Maximum brake disc lateral runout (warpage) 10 lb. (4.5 kg) Upward force applied at midpoint of bottom belt strand Drive belt deflection 3/8-7/16 in. (9.5-11.1 mm) FLHTP 1/4-5/16 in. (6.4-7.9 mm) FLHP/FLHPE 40-60 in-lbs (4.5-6.8 Nm) Air cleaner cover bracket screw torque Air cleaner 36-60 in-lbs (4.1-6.8 Nm) Air cleaner cover screw torque LOCTITE MEDIUM STRENGTH THREADLOCKER 243 (BLUE) Air cleaner cover screw Threadlocker Part No. 99642-97 (6 ml) LUBIT-8 SUPER OIL, Part No. 94968-85TV (1/4 fl. oz.) Lubricant part number Clutch cable 35-45 in-lbs (4.0-5.1 Nm) Handlebar switch housing screw torque

Incoming search terms: