HARLEY DAVIDSON FX SOFTAIL FRONT LOWERING SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (T), lockwashers (S), flat washers (R) and axle cap from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) and spacer (O) from fork tube plug (B). Remove quad ring seal (D). Save bolt and spacer but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring -J03923 1 of 4 pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring (1). 11. Remove dust cover (E). 12. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 13. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 14. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). NOTE The lower stop (L) may come out with the damper tube or remain in the slider tube. Ensure that the lower stop is removed from the slider tube. 15. Remove the lower stop (L). 16. Remove damper tube (2) from fork tube. 17. Remove rebound spring (F) from damper tube. 18. Repeat Steps 1-17 for the opposite side fork assembly. Fork Assembly

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON XL FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
REMOVAL Remove Right and Left Forks 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. See the service manual and remove front wheel, fender and brake caliper. 3. Spray glass cleaner on the fork tube between upper and lower fork bracket to lubricate. 1 2 2 is04050 1. Fork cap bolt 2. Pinch bolt Figure 1. Loosen Pinch Bolt 3 2 1 is00154 1. Vise grip 2. Rubber pad 3. Plastic knob Figure 2. Fork Tube Holder (HD-41177) 4. See Figure 1. While holding the fork slider to prevent the fork from dropping, loosen pinch screws (2). 5. Remove fork tube by sliding the fork tube down and out of the upper and lower fork brackets. 6. Repeat Steps 3-5 to remove opposite fork. -J04713 1 of 5
7. Move forks to bench area. Place suitable drain pan on floor beneath vise. Disassemble Left and Right Fork

Harley Davidson HIGH PERFORMANCE QUICK- INSTALL ADJUSTABLE PUSHRODS INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Remove stock pushrods using a bolt cutter. 2. Place the motorcycle on a hydraulic center stand with the rear wheel raised off the ground. Remove spark plugs. CAUTION 1 WARNING 1 WARNING CAUTION 1 WARNING CAUTION ® i02097.tif Figure 1. Adjustable Push Rod Kit Number 17997-99A Pushrod Tube Adjusting Screw Flats Adjusting Screw Locknut 1 of 2 Exhaust Pushrod Tube has Thicker “Finished” area and is slightly longer Intake Pushrod Tube has Thinner “Finished” area and is slightly shorter 3. With transmission in gear use rear wheel to turn engine over until both front cylinder tappets are at their lowest point. 4. Replace O-rings, lower pushrod cover and spring cover keeper with new components supplied in kit. 5. See Figure 1. Loosen locknut on all of the pushrods and adjust them to their shortest length. NOTE See Figure 1. In Step 6, pushrods with the Thinner “Finished” area on the tubes must be installed to the Intake location on the cylinders; pushrods with the Thicker “Finished” area on the tubes are slightly longer and must be installed to the Exhaust locations on the cylinders. 6. Install pushrods with pushrod covers. Be sure adjuster end of pushrod is down and ball end of adjuster is in tappet socket. 7. If hydraulic tappets are used, adjust pushrods following procedure A. With solid tappets, follow procedure B. NOTE Pushrod adjustment must be made with engine cold. PROCEDUREA (Hydraulic Tappets) 1A. Adjust pushrod length to zero clearance. 2A. See Figure 1. With the pushrod tube kept from rotating with a 1/2 inch or adjustable wrench, slowly turn the adjusting screw with a 5/16 in. wrench, 2-1/2 complete turns counter clockwise (lengthening the pushrod) as viewed from the bottom. (You may wish to mark adjuster to aid in counting turns.) 3A. Hold adjusting screw and tighten locknut with 1/2 in. open end wrench against the pushrod tube. If pushrod turns with locknut use three open end wrenches, one to hold the pushrod tube, one to hold adjusting screw and one to turn locknut.

Incoming search terms: