1500 XLT MOTORCYCLE / ATV LIFT INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
1. Load should not exceed rated capacity for this lift – 1500lbs 2. 70-160PSI shop air needed. 3. Make sure the handle is in the down position and the safety plate is set in the safety lock while the lift is in the raised position. 4. Move the lift only when it is lowered. 5. Do not ride vehicle onto lift. 6. Only trained people should operate the lift. 7. Air/Hydraulic pump should be at least 3 feet away when operating. Remain clear of the lift when raising or lowering. 8. Indoor use recommended. 9. Do not move lift while loaded. 10. Keep hands, tools and other extremities from under carriage and moving parts.. 11. Maintain a safe working environment. The work area should be clean, dry, clutter free, and sufficiently lit. 12. Wear proper ANSI-approved safety attire. Do not wear loose fitting clothing while operating lift, long hair and sleeves should be secured. 13. Keep children and bystanders away from work area. Do not let children operate or play on lift. 14. Do not use if under the influence of drugs or alcohol. Operator must be alert at all times when using heavy lift equipment. 15. Never operate the lift with someone on it. 16. Do not adjust safety valve. 17. Use this lift only for the work it is intended. Do not use this product for an application for which it was not designed. Misuse can lead to personal injury and/or property damage. 18. Industrial applications must follow OSHA requirements. 19. Do not use for aircraft purposes. 20. Have your lift serviced by a qualified repair person using only identical Titan Lifts® replacement parts and attachments. This will ensure that the safety of the lift is maintained.

AIR / HYDRAULIC MOTORCYCLE LIFT REMOVABLE INSPECTION PLATE

0

Filed Under (Tips and Review) by admin on 19-11-2010

download
For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram on the next page. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. NOTE: If an automatic oiler is not used, put 3-5 drops of pneumatic Tool Oil (not included) in the Motorcycle Lift’s Quick Coupler (38A) before each use. (See Figure B, next page.) To Check The Level Of Hydraulic Oil: 1. The Motorcycle Lift already contains some hydraulic oil in its Hydraulic Pump Reservoir (32P). Even so, it is recommended that you check the oil level in the Reservoir and, if necessary, top off the Reservoir with the proper amount of 15/40 hydraulic oil (not included). (See Assy. Diagram, page 15.) 2. Make sure to screw the two Adjusting Screws clockwise enough to lift the two Caster Wheels (14) off the floor so as to provide stability for the Motorcycle Lift. (See Figure A.) 3. To check the level of hydraulic oil, remove the Sliding Plate (36) from the Platform (35) to expose the Hydraulic Pump Reservoir (32P). (See Assy. Diagrams, pages 13 and 15.) 4. Remove the rubber Filler Plug (33P) located on the top of the Reservoir (32P). If necessary, top off the Reservoir with hydraulic oil. (See Assy. Diagram, page 15.) 5. Connect the air compressor’s hose to the to the Air Motor assembly. Then turn on the air compressor and set its regulator at 120 PSI. (See Assy. Diagram, page 14.) 5. Insert the Lift Foot Pedal (11) onto the Pump Piston Spindle (9), and slowly pump the Lift Foot Pedal until a slight amount of hydraulic oil begins to leak out of the Reservoir (32P). Discontinue pumping the Lift Foot Pedal. Then, replace the Filler Plug (33P) on the top of the Reservoir. (See Assy. Diagram, page 15.) REGULATOR OILER FILTER TO QUICK COUPLER (38A) OF MOTORCYCLE LIFT FIGURE B 6. Insert the Release Foot Pedal (10) onto the Release Valve Spindle (5). Pump the Lift Foot Pedal (11) until the Platform (35) of the Motorcycle Lift reaches its maximum height. Then press down slightly on the Release Foot Pedal until the Platform is fully collapsed to the floor. Repeat this procedure several times to ensure the Motorcycle Lift is operating properly. (See Figure E, page 10.)

Incoming search terms:

Titan 1500-XLT INSTALLATION, OPERATION, And MAINTENANCE MANUAL

0

Filed Under (Titan) by admin on 01-11-2010

download
UNPACKING AND SET-UP *REFER TO PARTS LIST FIG. 1 1. Carefully unpack the lift making sure that all of the parts have been included. 2. Remove the lift and all parts from delivery pallet and place on a clean, solid flat surface. 3. Take end of black hydraulic hose and attach to pneumatic/hydraulic pump (48). 4. Raise the lift with pump foot pedal (58) to expose the top of casters. Note: If the lift is not raising level, check to make sure that the wheels (42) are in their tracks. 5. Use the provided Allen wrench and place in top of casters (22) and turn it clock-wise. Raise all four casters until the lift rolls freely. 6. If using the front extension (9), slide the front extension over the front of the deck plate. Use the second and third connecting bars (5) and secure to the deck plate with the pipe guards (3), and R-pins (4), or use short connecting bar (68) without side extensions. 7. If using side extensions (7) then use the connecting bar (5) to assemble the side extensions (7) to the deck plate (8) securing them with the pipe guards (3) and R-pins (4). Slide the side extensions (7) to the deck plate (8). 8. Take ramp stands (43) and screw into bottom ramps (44) (45) and (46). Place the extension ramp (47) over matching holes on the center ramp (45). 9. Take the fixed clamp (10) and bolt to location “B” on the deck plate (8) or front extension (9) using bolts (11), washers (12), lock washers (13), and nuts (14) . 10. Take the movable clamp (16) and bolt to location “C” on the deck plate (8) or front extension (9) using bolts (11), washers (12), lock washers (13) and nuts (14). 11. Insert the tire stop (15) onto the fixed clamp (10) using the pin (60). 12. Place stands (1) on holes located on the end of the deck plate (8). 13. If you have access to compressed air, attach air nozzle to compressed air hose and raise the lift by pressing lever on air nozzle. Requires 70-160PSI. 14. If necessary, raise or lower the adjustment legs (6) to make the lift deck plate level with the ramps.