2003 – 2005 Corolla HEATER PERFORMANCE IMPROVEMENT REPAIR

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
Install the SST to the piping clamp. SST: 09870-00015 HINT: Confirm the direction of the piping clamp claw and the SST using the illustration shown on the caution label. B. Push down the SST and release the clamp lock. NOTE: Be careful not to deform the tube when pushing the SST. C. Pull the SST slightly and push the release lever. Then remove the piping clamp with the SST. D. Remove the piping clamp from the SST. E. Disconnect the cooler refrigerant suction hose No. 1. NOTE: Disconnect the tube by hand only. Do not pry the tube apart. Cap the open fittings immediately to keep moisture or dirt out of the system

2003 – 2004 Matrix FOG LIGHT INSTALLATION PROCEDURE AND REMOVAL

0

Filed Under (Toyota Manuals) by admin on 29-10-2011

download
Check that the fog light installation parts on the front bumper are the new shape. 2. If the bumper is the previous design, cut off the part indicated in the illustration. 3. Install the fog ligh New style fog lights have been developed for the Matrix. The front bumper has been modified to accommodate this change. In order to install the new style fog lights into the old bumper design, the following procedures must be followed

Toyota Noise from Auxiliary Port with External Device

0

Filed Under (Toyota Manuals) by admin on 09-10-2011

download
2006-2008 4Runner, Prius, RAV4 2007 Camry, Camry HV, FJ Cruiser, Yaris 2007-2008 Solara TSB SUPERSESSION NOTICE The information contained in this TSB supersedes TSB No. AU004-07. •Applicability has been updated to include 2008 model year 4Runner, Prius, RAV4, and Solara. •Parts Information has been updated to includea clarifying illustration. TSB No. AU004-07 is Obsolete and any printed versions should be discarded. Be sure tore view the entire content of this service bulletin before proceeding. Introduction Some customers may notice noise in the auxiliary mode of their audio system when using an MP3 player or other external audio source connected to the 12Vpowerportof the vehicle. An improved auxiliary port and in-line filter has been developed to improve this condition.Use the repair procedure below to install the new in-line filter and auxiliary port

TOYOTA Oil FilterCap Assembly Precautions

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
2010 Camry 2009-2010 Corolla, Matrix 2009 Highlander, RAV4, Venza 2008-2009 Land Cruiser 2008-2010 Sequoia 2007-2010 Tundra TSB SUPERSESSION NOTICE The information contained in this TSB supersedes TSB No. T-SB-0332-08. •Applicability has been updated to include 2009-2010 model year Highlander, 2010 model year Camry, Corolla, Matrix, Sequoia, Tundra, and 2009 model year Venzavehicles. •The SSTtablehasbeen updated with an illustration. •The Noticeinthe Repair Procedure has been updated witha Figure and torque specification ranges to clarify SST usage. TSB No. T-SB-0332-08 is Obsolete and any printed versions should be discarded. Be sure to review the entire content of this service bulletin before proceeding. Introduction To prevent damage to the oil filter cap assembly, this procedure must be closely followed during oil filter replacement to avoid immediate and future oil filter serviceability concerns. The following engines are equipped with aplastic oil filter cap assembly: •1UR-FE (Tundra, Sequoia) •3UR-FE (Tundra, Sequoia, Land Cruiser) •2ZR-FE (Corolla, Matrix)

HARLEY DAVIDSON FRONT SPOILER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation NOTE The spoiler in kit number 58882-04BDK is finished with a primer coat. Before installation, have the spoiler painted 1. Mount the motorcycle on a lift table. 2. See the Service Parts illustration. Attach the upper front spoiler bracket (4) to the bosses on the inside front of the spoiler (1) with the two Hi-Lo screws (10) from the kit. Tighten to 15-20 in-lbs (1.7-2.3 Nm). 3. Attach the lower front spoiler bracket (5) to the two weld nuts in the cross bar at the bottom front of the motorcycle frame with two hex head machine screws (6) and split lockwashers (7) from the kit. Torque to 30 ft-lbs (41 Nm). 4. Remove the protective film from the back of the medallion. Carefully center the medallion on the recessed area on the front of the spoiler. 5. Press the Bar and Shield medallion (3) firmly into position. Hold the medallion in place, pushing hard with your thumbs, for about five seconds. Take care not to shift the medallion on the spoiler. 6. After releasing pressure, avoid direct contact with the medallion for about 20 minutes. 7. Place a flat washer (9) on one of the pan head machine screws (8) from the kit. Position the spoiler to the front of the frame. Insert the screw through the large hole in the bottom of the spoiler and thread it into the upper front spoiler bracket, but do not fully tighten at this time. 8. Place a flat washer on each of the two remaining pan head machine screws from the kit. Insert the screws through the slots in the bottom of the spoiler and thread them into the lower bracket, but do not tighten fully. 9. Position the spoiler next to the vehicle frame allowing an equal amount of minimal clearance. Alternately tighten the three screws to 72 in-lbs (8 Nm)

HARLEY DAVIDSON XL STARTER MOTOR COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. Remove exhaust system according to Service Manual instructions. 2. See Figure 1. Remove the outer primary screw shown and retain it for reinstallation. 3. See Service Parts Illustration. Insert the thread cleaning screw (9), through the primary cover and the crankcase until the full screw diameter protrudes through the crankcase. Remove any debris from from the tip of the thread cleaning screw. Remove thread forming screw and discard. NOTE If thread cleaning screw binds in crankcase hole, remove thread cleaning screw and chase threads with 1/4 – 20 tap. 4. Install set screw (8) from outer primary side using the wrench provided. Set screw should extend past the crankcase approximately .375″. 5. With wrench in set screw to prevent rotation, install the backplate over the set screw and fasten with the 1/4-20 nylock nut (5). 6. Reinstall the primary cover screw saved in Step 1. Torque to 80-110 in-lbs (9-12 Nm). 7. Remove the the oil hose clamp from the starter stud. Do not remove the clamp from the hoses. 8. Replace the original equipment starter stud with stud (7) provided. Torque to 39-65 in-lbs (4-7 Nm). 9. Install bracket (2) over stud (7) and fasten with #10-24 nylock nut (6). Rotate bracket until the tab on the bracket rests on starter motor. 10. Install oil hose clamp onto bracket (2) using one of the #10-24 screws (4). Tuck the hoses down as far as possible without contacting the drive belt or kinking the hose. Contacting the drive belt or kinking the hose may cause damage to the hoses or powertrain. 11. Install the cover (1) to the backplate (3) and bracket (2) using four of the #10-24 screws (4) with the wrench provided. The cover should fit inboard of the gear cover and partially on top of the sprocket cover. Start the bracket screw first, then follow with the (3) backplate screws. 12. Reinstall exhaust system according to Service Manual Instructions

HARLEY DAVIDSON DETACHABLE TOUR-PAK LIGHT HARNESS KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 2. ALL models: Install the Detachable Tour-Pak Rack Kit per the instructions in that kit, up to the point where the saddlebags are to be re-installed. NOTE Make note of the cable strap locations before releasing the harness from the upper frame tube. New straps will be fastened in the same location. 3. Cut the larger cable strap fastening Tour-Pak circuit [12] (see the Service Manual Wiring Diagram) of the vehicle main harness to the left-side upper frame tube, rearward of the shock absorber. Cut the small cable strap at the end of the circuit [12] conduit. 4. Slit the conduit open along its length to expose the final ten inches (0.25 M) of main harness circuit [12] wiring. Cut the three wires (Black, Blue, and Red with Yellow tracer) nine inches (0.23 M) from the three-way Multilock socket housing [12B]. The socket housing and cut wires can be discarded. 5. Obtain the socket housing, secondary lock (locking wedge), and three socket terminals from the kit. See the illustration at DEUTSCH ELECTRICAL CONNECTORS: REMOVING/INSTALLING SOCKETS in the Service Manual. Refer to CRIMPING INSTRUCTIONS in the Service Manual, and follow the instructions to install the terminals to the three wire leads of main harness circuit [12]. 6. Per the instructions under DEUTSCH ELECTRICAL CONNECTORS, insert the Blue lead and terminal into Cavity 1 of the new socket housing. Insert the Red/Yellow lead and terminal into Cavity 2. Insert the Black lead and terminal into Cavity 3. 7. Cut the excess conduit from main harness circuit [12]. 8. Obtain the two cable straps from the kit. As noted in Step 3, use one strap to bind the end of the main harness circuit [12] conduit. Use the second strap

HARLEY DAVIDSON DYNA CHROME COIL COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Installation 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Note the position of each spark plug wire in the ignition coil, then disconnect the two wires. 3. If there is an existing coil cover: Remove and discard the coil-cover mounting screws and spacers. Remove and discard the coil cover. If there is not an existing coil cover: Remove and discard the two coil mounting screws. 4. See the Service Parts illustration. Obtain the coil cover bracket (3), two long screws (4) and two spacers (2) from the kit. 5. Insert the screw into one of the holes in the bracket as shown, through a spacer, and into a coil mounting hole. Repeat with the second screw and spacer. 6. Assemble the coil to the electrical caddy with the two screws. Tighten the screws to 50 in-lbs (5.6 Nm). 7. Obtain the new chrome coil cover (1) from the kit. Position the cover over the coil, and fasten to the coil cover bracket with the three chrome screws (6) and washers (7) from the kit. Do not fully tighten the screws at this time. 8. Connect the spark plug wires through the holes in the side of the coil cover onto the correct coil terminals. 9. Adjust the cover to center the spark-plug wire boots in the coil cover holes for best appearance. Tighten the three chrome screws securely 10. Refer to the Service Manual and follow the instructions given to install the maxi-fuse

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE FORK BRACE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-02-2011

download
installation 1. See Service Parts illustration on page 2. On all models except those equipped with 39mm forks, push the dust covers off of the sliders and up the fork tubes until out of the way. On models equipped with 39mm forks, the fork brace fits over the dust cover. 2. Using allen wrenches, remove screws (1) and end caps (5 and 6) from brace halves (3 and 4). 3. Loosen screws (2), push brace halves together and insert between fork tubes. Heads of screws (2) must face towards the engine. 4. Make sure brace is down tight on fork sliders (dust covers on 39mm fork equipped models) and install end caps (5 and 6). Lightly secure end caps with screws (1). 5. Align brace halves (3 and 4) tighten screws (2) finger tight. 6. Push down on front forks several times to seat fork brace and allow it to self-align. It is very important to tighten all screws evenly and carefully to prevent binding. 7. Tighten end cap screws (1) and brace screws (2). 8. Slide dust covers down onto fork brace (except 39mm fork equipped models).

Incoming search terms:

HARLEY DAVIDSON SADDLEBAG RAIL BRACKET KIT INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation 1. See Figure 1. Remove two stock screws and nuts from one side of the saddlebag rail assembly. 2. See the Service Parts illustration. Insert two screws (3) through the screw holes from the opposite direction as the stock screws removed from the rail bracket in Step 1. 3. Place a spacer (2) on the outboard screw. 4. Place a Saddlebag Rail Bracket over the rail assembly. Position the bracket with the square notch on the inboard side of the rail assembly. 5. Fasten the screws from step 2 into the Saddlebag Rail Bracket. Torque the fasteners to 10 ft-lbs (13.5 Nm). 6. Repeat steps 1 – 5 for the saddlebag rail assembly on the other side of the motorcycle