Harley-Davidson BIG-TWIN 8mm BELT DRIVES (OPEN OR CLOSED) INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
INSTALLATION : The spacer behind the front pulley should be removed prior to installing the belt drive. This spacer may or may not be required to correctly align the pulleys. If a spacer is needed for alignment, various sizes are available from your local Primo Belt Drives dealer (part number PX-1 =package of 6 various sizes). With all supporting components installed, install front pulley, lubricate and reinstall the clutch hub. Loop the belt around the front and rear pulleys, and gently push into place. Use the washer and nut supplied with the kit on the front motor shaft, (always use an impact wrench on splined shaft motors) tighten to 80-100 foot pounds of torque. After installing and adjusting clutch, track the belt by turning the pulleys. If needed us a straight edge between the front and rear pulleys to check alignment. Improper alignment of the pulleys will result in reduced belt life. Spacing the motor pulley outward will cause the belt to track towards the outer primary cover. If spaced too far out the belt will rub on the inside of the clutch shell. ENCLOSED INSTALLATIONS: The same disassembly is required, with the exception of the clutch hub and inner primary. We recommend using our PC-1000-Acomplete clutch assembly. Loop the belt around both pulleys to insure that you have the proper belt for your pulleys, then gently push the unit into place. Use the washer and nut supplied with the kit on the motor shaft. Torque the motor nut to 80-100 foot pounds . Adjust the clutch & check belt / pulley alignment. Before installing the primary cover be sure that everything inside clears both the outer and inner covers. In some cases a small amount of metal may need to be removed from one or more of the bosses on the inner or outer primary covers

2008 Honda CBR1000RR Clutch Inner Installation PROCEDURE

0

Filed Under (Honda) by admin on 23-04-2011

download
Refer to the 2008 CBR1000RR Service Manual for specific removal instructions. While completing this procedure, be careful not to damage the covers, cowls, or any other components. 1. Remove the air intake cover (page 3-8). 2. Remove the upper inner cover (page 3-9). 3. Remove the lower cowl (page 3-9). 4. Remove the right middle cowl (page 3-10). 5. Remove the right crankcase cover (page 10-5). Clutch Removal (page 10-7) 6. Remove the starter idle gear and shaft. 7. Remove the snap ring and stopper ring. 8. Remove the clutch lifter piece and plate. 9. Unstake the clutch center lock nut. Be careful not to damage the mainshaft threads. 10. Hold the pressure plate with the special tool. You must use the special tool (Clutch Holder, T/N 070MB-MFLA100) when removing the lock nut. Using an impact wrench will damage the main shaft threads. Clutch Holder: 070MB-MFLA100 (autoshipped in May 2008) 11. Remove the clutch center lock nut and washer and discard the lock nut as shown on top of page 3 12. Remove the clutch spring holder, spring seat, and two clutch springs. 13. Remove the spring seat. 14. Remove the following: • Pressure plate
• Spring seat • Judder spring • Clutch disc A • Clutch plate A • Seven clutch discs B • Clutch disc C  Clutch center NOTE: Do not remove the clutch outer. New Clutch Installation (page 10-20) NOTE: The new clutch disc assembly has a dif- ferent order of plates than the illustration shown in the Service Manual. Keep note of this when repairing updated units.
15. Install the new clutch disc assembly with- out removing the setting bolts. Rotate the main shaft to align the clutch disc assem- bly with the main shaft spline. 16. Slightly loosen the setting bolts. 17. Rotate clutch disc C to align its tabs into clutch outer shallow slots, then fully install the clutch disc assembly. 18. Remove and discard the setting bolts. 19. Install the spring seat

Incoming search terms:

HARLEY DAVIDSON FXST BLACK FORK SLIDER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION The fork sliders included in this kit install in the same way as the original equipment parts. NOTE Prior to installation of this kit, check the bores of the new sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s), and front wheel according to instructions found in the Chassis section of the appropriate Service Manual. NOTE On some models other parts will also need to be removed to access the front forks. See the Service Manual. 3. Drain and remove the front forks. See the Chassis Section of the Service Manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 4. Disassemble the front fork tubes according to instructions in the Service Manual, and replace the original fork sliders with the black sliders from the kit. 5. Assemble the front fork tubes, replacing worn seals, bushings or other additional items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 6. Tighten the drain screws to 52-78 in-lbs (5.9-8.8 Nm) 7. Fill with Harley-Davidson TYPE E FORK OIL according to the instructions found in the Service Manual. 8. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel, and caliper(s) according to the instructions found in the Chassis section of the Service Manual. Federal Motor Vehicle Safety Standard (FMVSS) 108 requires motorcycles to be equipped with rear and side reflectors. Be sure rear and side reflectors are properly mounted. Poor visibility of rider to other motorists can result in death or serious injury. (00336b) 1 is02733 1. Install bottom of reflector 2.0 inches above center of axle Figure 1. Reflector Placement NOTE The front reflectors located on both sides of the fork sliders will be removed, cleaned and installed on the new chrome fork sliders. 9. See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side to side until it can be removed. Retain reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. 10. Peel off any excess adhesive from both reflectors. Surface must be clean for reinstallation. 11. Peel off one side of backing on foam double sided tape. Press firmly on tape to secure it to reflector. Repeat double sided adhesive tape installation on remaining reflector. NOTE The bottom edge of reflector should be two inches (50 mm) above the center of the axle shaft. 12. See Figure 1. Remove second side (outside surface) of adhesive backing. Place reflector in position (1) and press reflector firmly into place to activate the adhesive. Repeat for remaining reflector. 13. Pump brakes prior to test riding vehicle.

HARLEY DAVIDSON CHROME FORK SLIDERS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
REMOVAL 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s) and front wheel according to instructions found in the Chassis section of the appropriate service manual. NOTE On some models other parts will also need to be removed to access the front forks. See the service manual. 3. For All Models EXCEPT Touring: Drain and remove the front forks. See the service manual. 4. For Touring models equipped with air-adjustable suspension: Bleed the air-adjustable suspension according to the instructions in the appropriate service manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 5. For 2000 and Later Models EXCEPT Touring: See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side-to-side until it can be removed. Save reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. Peel off any excess adhesive from both reflectors . Surface must be clean for installation. 6. Disassemble the front fork tubes according to instructions in the service manual. INSTALLATION NOTES The chrome fork sliders included in this kit install in the same manner as the original equipment parts. Refer to the service manual for proper installation procedures. Prior to installation of this kit, check the bores of the new chrome sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Assemble the front fork tubes, replacing worn seals, bushings or other items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 2. Tighten the drain screws: •Early Models with 39 mm forks (see Figure 2): Tighten to 13-17 in-lbs (1.5-1.9 Nm) •Early Models with 41 mm forks (see Figure 2): Tighten to 52-78 in-lbs (5.8-8.8 Nm) •Later Models (see Figure 3): Tighten to 52-78 in-lbs (5.8- 8.8 Nm) 3. Fill with TYPE E FORK OIL (99884-80) according to the instructions in the service manual. 4. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel and caliper(s) according to instructions in the service manual. 5. For Touring models equipped with air-adjustable suspension: Refill the air-adjustable suspension system after assembly according to the service manual instruc- tions

Incoming search terms:

YAMAHA XS650 Garage Carburetor Guide Introduction

0

Filed Under (Yamaha) by admin on 31-10-2010

download
Loop the hose around the bottom of the yardstick and secure it with wire or twist ties so that it runs straight up both sides; avoid pinching. Trim the ends to the same length, and cut an 8″ piece from each end. Suck ATF into the line so that it fills the tubing about 8″ high on each side. Splice the end pieces back on with the pilot jets. Remote Fuel Bottle. On OEM carbs with a central synchronizing screw,adjustment (see Section II.) is easiest with the tank removed. Make a remote tank from a 1 qt. plastic bottle. Install a 1/4″ hose barb in the bottom of the bottle and a lawn mower fuel valve in the line (an in-line filter is also a good idea). Attach a wire to the top of the bottle and hang it where you need it. Safety note: many plastics will break down with exposure to fuel. Be sure your material is fuel resistant, and empty the container immediately after use. This item is not strictly necessary. 5twins recommends rough adjustment with the tank removed, using fuel remaining in the float bowls, followed by fine adjustment with the tank in place, reaching in with a long screwdriver. You can also set the tank on a work bench or other elevated surface and run extensions to the carburetor lines. Compressor If you intend to do much mechanical work at all, an air compressor with sufficient capacity to power an impact wrench will pay for itself quickly. For carb cleaning, attach an air gun with a rubber tip.

Incoming search terms:

KAWASAKI TERYX 750 CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove both seats from the vehicle. Next, remove the passenger side lower body panel. There is a mixture of Philips head screws and also plastic push pin fasteners that have to be removed. 2. With the side panel off, the next item to remove is the plastic housing over the engine. These are all “push in” style plastic clips that hold it in place. Once all the pins are out, you can slide the housing off and set it aside. 3. Now the lower long plastic panel under the seat has to be removed (again mainly plastic push clips to remove) . Once they are all out, carefully remove and set aside. 4. Next, remove the fuel tank. Remove the two lines on the top of the tank. There are two straps that hold the tank in place. Remove the bolt from each strap, remove the straps, and lift the fuel tank out. 5. Now the bracket that holds the fuel pump on has to be removed. There are two bolts here to take out. Once this is done, mark the two wires to the coil and disconnect them. Set the bracket out of the way . 6. Next, the clutch cover bolts can be removed and the norkel on the housing can be loosened and i Teryx 750 Clutch Kit Instructions 5/1/09 removed. Take the clutch cove off and set out of the way. 7. With the clutch visible, you can remove the secondary clutch with a large impact wrench and metric socket . 8. Remove the bolt from the primary clutch. This is a left hand thread on the bolt. Next you will need a Kawasaki drive clutch puller (part #352251) to pop the clutch loose. If you do not have a puller, the spring cap can be removed on the vehicle and the weights can be changed out in there as well. 9. With the clutches sitting on the bench, remove the bolts that hold on the spring cover. Remove the stock spring and the stock weights 10. After reading the directions on the new weights, add the correct amount of weight to each clutch weight and install them in the clutch. Place the weight to the left side in the clutch pocket and then install the aluminum spacer. Repeat this process for the other three weights. 11. Install the new spring supplied in the kit and install the spring cover, paying close attention to the arrows on the cover. 12. Next, remove the stock spring from the secondary. It is recommended that you use the TEAM Compression tool (part # 930001) for this. With the clutch on the compression tool, compress the spring retainer down far enough to remove the snap ring with the needle-nose pliers . Slowly back off the t-handle and remove the tool.