2004 Harley Davidson Micro Tach Tachometer Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-03-2012

download
Tachometer Installation Instructions for 2004+ Harley Davidson Sportster Custom Look for other model instructions online at www.speedwayinstruments.com Introduction: Installation of the Speedway Instruments microTach+ TM tachometer Tachometer requires some basic mechanical skills, including removing decorative covers, cutting protective tubing around wires, and using suitcase splice connectors to splice existing wiring harness. These actions may void your warranty, and if done incorrectly may cause damage to your motorcycle. Only you know your capabilities, if you do not feel capable of making modification please have a qualified motorcycle technician install it. Speedway Instruments, LLC is not responsible for damage to your motorcycle due to improper installation. These instructions utilize a 2004 Harley Davidson XL1200C motorcycle as basis for the all descriptions and pictures. Variations in location, color and procedure may be required for different year and make. Please refer to the Service manual to confirm the proper color and location of wires. Please make sure you have the proper service manual and tools before starting the installation. 1. Turn ignition off and disconnect Battery. 2. Determine a mounting position. Each motorcycle is unique and the microTach+TM tachometer is small enough to be placed in many different locations to provide an attractive appearance and vital engine status. Possible locations are: a. Front Brake Reservior b. Top handle bar clamp

1999-2003 Harley Davidson TC88 Micro Tach TM Tachometer Installation Manual

0

Filed Under (Harley Davidson) by admin on 10-03-2012

download
Installation of the Speedway Instruments microTach+TM tachometer requires some basic mechanical skills, including removing decorative covers, cutting protective tubing around wires, and using suitcase splice connectors to splice existing wiring harness. These actions may void your warranty, and if done incorrectly may cause damage to your motorcycle. Only you know your capabilities, if you do not feel capable of making modification please have a qualified motorcycle technician install it. Speedway Instruments, LLC is not responsible for damage to your motorcycle due to improper installation. The microTach+ TM tachometer designed for 1999-2003 TC88 Harley Davidson motorcycles is designed to operate when connected to a dedicated Tachometer signal from the Electronic Ignition Controller. It is not intended to run off signals going to the ignition coil unless utilizing a Speedway Instruments Tach Adapter. WARNING: Damage may occur to the microTach+ TM tachometer or your motorcycle if micro Tach+ TM tachometer is connected directly to coil signals, you must use a Speedway Instruments tach Adapter (sold seperately) ! ! 1. Turn ignition off and disconnect Battery. 2. Determine a mounting position. Each motorcycle is unique and the microTach+TM tachometer is small enough to be placed in many different locations to provide an attractive appearance and vital engine status. Possible locations are: a. Front Brake Reservoir

Yamaha XV-1900 Braided Stainless Steel Thottle Cables Installation Instructions

0

Filed Under (Yamaha) by admin on 30-12-2011

download
Please read and understand these instructions completely before installation to avoid injury or damage to the motorcycle or accessory. IMPORTANT: Dealer installation is recommended. The installer should have the service manual for the motorcycle , as well as a good understanding of motorcycle service and repair techniques. Dealer: These instructions contain important information for future reference and must be given to the customer. 1. Parts List: Item Part Name Part Number Description Qty 1 Throttle Cable Set 07-1083 1 2. Preparation: a) Before installation, lubricate cable with an appropriate cable lube such as Motion Pro Cable Lubricant (P/N 15-0002) b) Securely place motorcycle on side stand 3. Installation: Refer to vehicle service manual for installation instruction and adjustment procedures. NOTE: Notice how original cable routed before removing it. Install the accessory cable in the same way. If unsure or original cable routing, refer to the cable routing diagram in the service manual. WARNING ∞ Before starting the engine, be sure the throttle operates smoothly and check that throttle body is fully closed when throttle is released ∞ After starting the engine, turn the handlebar to the right and to the left to be sure the throttle operation is not affected ∞ Improper installation could result in great bodily injury or death 4. Maintenance: Check throttle operation before each ride. Follow Periodic Maintenance procedures in the owner’s manual for adjustment and lubrication. 5. Care and Cleaning: See your Owner’s Manual

HARLEY DAVIDSON HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
Models Kit 50227-01 is designed for forward controls and fits: •1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1993 through 2002 FXDWG, •Dyna models equipped with Forward Control Kit 49080- 93 or 49080-93A. Kit 50227-01 does not fit Dyna models equipped with Forward Control Kit 49080-03 or Forward Control Footrest Support 33695-03 (left) or 33697-03 (right). Kit 50236-01 is designed for mid controls and fits: •all 1990 and later Dyna Model Motorcycles with Original Equipment (OE) Mid Controls. Additional Parts Required Proper installation of this kit also requires installing a pair of Heel Rest Pegs, or Shifter Pegs, which can also be mounted as heel rests. Refer to the appropriate Parts Catalog for stock shifter pegs, sold separately. The current Harley-Davidson Genuine Motor Accessories and Parts catalog also has a selection of Heel Rest Pegs or Shifter Pegs and matching Footpegs. Any shifter peg style that is symmetrical in design can be used as a left or right side heel rest. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE A Service Manual for your model motorcycle is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTE See Figure 1 for the following procedure. 1. Remove the screw (B), lock nut (C) and spring washer (E) securing the left footpeg to the footrest support bracket (A). Save the hardware for later installation. NOTE Heel rest levers are side-specific. Levers mount so the set screws are on the underside. 2. Obtain a Heel Rest Peg or Shifter Peg (D) (purchased separately) and the left side heel rest lever (3). Apply Loctite® 243 (7) to the threads of the peg and install it to the left heel rest lever. 3. Obtain the screw (B), spring washer (E) and lock nut (C) removed in step 1, and the heel rest lever and peg assembly (D). Position the lever assembly to the desired angle on the mount, and slide the lever assembly with the spring washer into the footrest support bracket as shown. NOTE Splines on the lever and mount provide for a limited range of heel rest angle adjustment. For Kit 50227-01. The heel rest lever (3) can be adjusted after the mount (1) is attached but before the set screw (2) is installed. Slide the lever inward off the spline, and rotate it to the desired angle. For Kit 50236-01. The heel rest lever (3) angle cannot be adjusted after the mount (1) is attached without removing them from the footrest support bracket (A). Check to ensure the heel rest (D) is in a comfortable position before tightening the mounting hardware. 4. Install the original screw (B) and lock nut (C) to secure the heel rest assembly to the footpeg mount. Tighten to 33 ft- lbs (45.6 Nm). 5. Obtain a screw (6), spring washer (5) and nut (4) from the kit. Install the footpeg to the heel rest assembly and tighten to 33 ft-lbs (45.6 Nm). 6. Obtain a set screw (2) from the kit. Apply Loctite® 243 (7) to the threads, and install the set screw to the heel rest lever. Tighten to 16 in-lbs (1.8 Nm). 7. Perform Steps 1 through 6 for the right side. USE

Incoming search terms:

HARLEY DAVIDSON AIRFOIL RIDER HEEL REST KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-04-2011

download
1989 and later FX Softail Models with Original Equipment (OE) Forward Controls, •1990 and later Dyna models (except 2003 and later FXDWG), •Dyna models equipped with Forward Control Kit 49080-93 or 49080-93A. Kit 50227-01 does notfit Dyna models equipped with Forward Control Kit 49080-03or Forward Control Footrest Support 33695- 03 (left) or 33697-03 (right). Proper installation of this kit also requires installing a pair of Airfoil Foot Rests, Part Number 50133-95 (large) or 50134- 95 (small), not included in this kit. Airfoil Foot Rests are available from your Harley-Davidson Dealer. See the Service Parts illustration for kit contents. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. NOTE A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. Installation NOTE When performing the following step, note the location and orientation of the spring washer when removing each footrest. 1. See Figure 1. On the right side of the motorcycle, remove the fastener securing the footrest to the footrest bracket. Save the hardware for installation. NOTE On motorcycles equipped with Airfoil Foot Rests, remove the adjusting screw fastening the foot rest to its footrest mount. Save the foot rest and screw for heelrest installation. 2. Fasten the Airfoil Rider Heel Rest mount and spring washer to the footrest bracket using the hardware saved from step 1. Tighten the fastener to 19 ft-lbs (26 Nm). 3. See Figure 2 and the Service Parts illustration. Place the right-side Airfoil Rider Heel Rest (2) on the Airfoil Rider Heel Rest mount (3), positioning the heelrest at the desired angle

HARLEY DAVIDSON CHROME FOOTPEG BOLT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE The bolts supplied in this kit are designed for a one-time installation only. If this kit is removed after initial installation, you must re-apply Loctite 243 (Blue) to the threads of the bolts. Kit Contents 3 1 3 is05122a Figure 1. Service Parts: Chrome Footpeg Bolt Kit Table 1. Service Parts Part Number Description (Quantity) Item 94128-01 Washer, chrome (2) 1 8023 Nut, chrome (2) 2 4233 Screw, TORX®, button head, chrome (2) 3 INSTALLATION 1. Remove existing nut and bolt securing footpeg to mount. Discard nut and bolt. 2. See Figure 2. Install chrome washer to bolt, then install bolt through mount and footpeg as shown. 3. Install nut to bolt. Tighten hardware to 10-16 ft-lbs (13.6- 21.7 Nm) . 4. Repeat Steps 1 through 3 for the opposite side

HARLEY DAVIDSON 80-SPOKE REAR WHEEL KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
Additional Parts Required This kit includes the custom wheel only. Proper installation of this kit requires the separate purchase of the following parts which are available at a Harley-Davidson dealer: •Wheel Bearing Remover and Installer (HD-44060) •Wheel Installation Kit (See Service Parts Tables for part number) The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See the Service Parts section for kit contents. INSTALLATION 1. Remove existing rear wheel assembly. Save axle, axle nut, brake disc and wheel spacers for kit installation. NOTE Remove the rear brake caliper before removing the wheel. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) 2. Install the tube and tire on wheel. Refer to REAR WHEEL in the Service manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) NOTES Install the primary bearing first using appropriate Service Manual and WHEEL BEARING REMOVER/INSTALLER. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to REAR WHEEL in Service Manual. 4. Install rear wheel (1), stock axle and stock axle nut. Refer to REAR WHEEL in Service Manual

Incoming search terms:

HARLEY DAVIDSON HARDWARE/ TURN SIGNAL RELOCATION KIT FOR SPORTSTER LEATHER SADDLEBAG KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
Installation Instructions for 79052-04 and 79073-04 Do not exceed 7 lbs (3.17 kg) maximum load in each saddlebag. Additional weight can affect a motorcycle’s stability, handling characteristics, and safe operating speed which may lead to an accident resulting in death or serious injury. NOTE A pick tool (Snap-on TT600-3) will be required for 1996 and later models for removing and reinstalling a multi-lock amp con- nector. NOTE A Service Manual for your vehicle is available from your Harley- Davidson Dealer. Installation – Hugger Models Only (1994-1997) To perform the following steps for Hugger Models only, fender and frame must be sufficiently supported, as both shocks will need to be removed at the same time. An improperly supported vehicle could result in death or serious injury. A Service Manual is needed to install this kit. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson Dealer perform the installation. Improper installation of this kit could result in death or serious injury. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove seat, sissy bar and sideplate, if applicable. Retain hardware for reinstallation. Disconnect battery, negative cable first. 2. Properly support motorcycle under frame to prepare for removal of right and left shocks. 3. Remove rear buttonhead screw on each side of fender. 4. See Figure 1. With rear fender and frame securely supported, remove left and right shocks by removing upper nut (2), washer(s) (3) and shock cover (4). Remove bolt (6), washer (7) and locknut (8) at lower shock mount. Remove shock

HARLEY DAVIDSON SOFTAIL CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Kit Contents See Figure 3 and Table 2 for complete kit contents. See Table 1 for the grab strap part number associated with each seat kit. Table 1. Kit Numbers and Grab Strap Usage Grab Strap Kit Number 51332-07 51310-07 51910-08 51936-08 51701-06 51308-07 51365-07 51367-07 51387-06A 51388-06 51389-06 51390-06 51391-06 51392-06 51398-07 51365-07 51410-08 51411-08 51412-08 51414-08 51415-08 51416-08 51407-08 The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) INSTALLATION NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. FXST, FXSTB and FXSTS Models 1. See Figure 3 and Table 2. Unscrew the captive thumbscrew fastening the back of the original equipment (OE) seat to the vehicle. 2. Pull the seat slightly to the rear to disengage the tang at the front of the seat from the motorcycle frame. 3. Lift the front of the seat while pulling the seat carefully forward to remove the seat from the vehicle. 4. Remove the OE grab strap and attaching hardware. Save the hardware for later use. 5. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap. 2007 and Later FLSTF Models 1. Remove original equipment (OE) seat and mounting hardware following the instructions in the Owner’s Manual. 2. Remove and discard the OE grab strap and attaching hardware. 3. See Figure 3. Install two flange nuts (9) from the kit onto the OE grab strap mounting studs (as shown in Figure 1, Item 1). 4. Install the grab strap. See either “For Kit 51936-08″ or “For All Other Kits” to install the grab strap.

HARLEY DAVIDSON FRONT TYPHOON WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
If installing kit 44615-08, 40774-10, 44657-08 or 43300053 on a Dyna model with stock laced wheels, the separate purchase of stock brake disc (44553-06A) or polished brake disc (41500012) is required. The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) •Harley® Preserve™ Bare Aluminum Protectant (99845-07) Touch-up paint for painted wheels is available from a Harley- Davidson dealer: •Touch-Up pen, wheel, black (94482) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. 1 2 is06470 1. Closed brake disc 2. Open brake disc or floating rotor Figure 1. Front Brake Disc Styles Table 1. Front Disc Hardware Fitment Hardware Brake Disc 5 Stock disc screws (3655A) Closed disc Chrome screw kit (46646-05) includes 5 screws 5 Stock disc screws (3762M) and 5 disc washers (6966M) Open disc NOTE: Models equipped with dual front brakes and models being equipped with a wheel with dual brake mounting surfaces require twice as many screws/washers (10 total screws or 2 chrome screw kits if available). INSTALLATION NOTE Use plastic protectors on tire mounting tools and rim clamps when mounting a tire to a painted wheel. For wide low profile tires a tire mounting machine with a second arm to press down on the sidewall while the wheel is rotating is recommended.