UNIVERSAL HEAT DEMONS INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 17-02-2012

download
A. Open or remove the seat according to the service-manual instructions. !!! Warning !!! Warning To protect against shock and accidental start-up of the vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. !!! Warning !!! Warning Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. B. Disconnect the battery, negative cable first, according to the service-manual instructions. There are two options for installing the Heat Demons. Option A is doing the installation without removing the handlebar and Option B includes the removal of the handlebar. Two holes need to be drilled in the handlebar and the Option chosen depends on how comfortable the installer is on drilling holes in the bar. One advantage for removing the handlebar is the Right Handlebar Control can be left intact during the installation. The disadvantage is on some models the headlight and trim pieces need to also be removed along with the cables that are attached to the handlebar. Option A – Installation without removing the handlebar. The 4 level Controller can be mounted on the left or right side of the handlebar so choose the side and location that will provide the easiest installation and most convenient operation. The width between the holes will allow the Controller to be mounted directly to the clutch bracket or brake reservoir on many Yamaha, Honda, Kawasaki, Suzuki or Triumph motorcycles. On other motorcycles the back side clamp and cap screws are provided to mount the Controller to the handlebar

HARLEY DAVIDSON CHROME DUAL GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
Installation To protect against shock and accidental start-up of vehicle, disconnect the negative battery cable before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious personal injury. Removal DISCONNECT ELECTRONIC SPEEDOMETER AND TACHOMETER 1. Refer to applicable Service Manual procedure and remove seat. 2. Refer to XLH Service Manual procedure and remove fuel tank. On FXD models, remove fuel tank mounting bolts and lift tank. 3. See Figures 1 and 2. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Detach sensor harness from left frame tube. 1 WARNING 1 WARNING 1 WARNING 4. Detach headlamp assembly from top fork bracket, to allow removal of speedometer sensor harness. 5. Unscrew speedometer reset switch boot. Remove cover screws and covers from backs of gauges. NOTE Some early electronic speedometers and tachometers were wired directly into the gauge

BUELL ACCESSORY GAS CAP KIT INSTALLATION MANUAL

0

Filed Under (Buell) by admin on 29-03-2011

download
Installation NOTE When performing the following Steps, use the Fuel Tank Vent Valve Installation Kit (Part Number 91432-96Y). This kit consists of: * Fuel Tank Vent Valve Installation Aid * Fuel Tank Vent Valve Fitting Socket To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect battery cables, negative cable first. An open flame or spark may cause a fuel tank explosion if all traces of fuel are not purged from the tank. Use extreme caution when servicing fuel tanks. Gasoline is extremely flammable and highly explosive. Do not smoke or allow open flame or sparks anywhere in the area when working on fuel system components. Inadequate safety precautions could result in death or serious injury. 2. Remove gas cap. 3. Carbureted Models: Drain fuel tank. Disconnect hose clamp and fuel supply hose from fuel supply valve and drain fuel into suitable, clean container. See applicable Service Manual, Section 4 for complete, detailed procedure. Fuel Injected Models: Relieve pressure from fuel system. See applicable Service Manual, Section 4 for complete, detailed procedure. Drain fuel tank. a. Using suitable external fuel pump, such as a Gas Caddy, pump fuel from tank and into a suitable, clean container. b. See instructions for external fuel pump for correct use. 4. See Figure 1. Cut cable tie securing vent hose to fitting and remove vent hose from fuel tank. Even with the fuel tank completely drained, a small amount of gasoline may leak from the bore when the fuel supply valve is loosened or removed. Thoroughly wipe up any fuel immediately and dispose of rags in a suitable manner. Gasoline is extremely flammable and highly explosive. Inadequate safety precautions could result in death or serious injury. 5. If the fuel supply valve requires cleaning or repair, refer to applicable Service Manual, Section 4, for complete, detailed procedures. 6. See Figure 1. Remove the fuel filler cap and O-ring. 7. Remove the eight self-tapping screws from fuel clamp flange and remove fuel cap flange

Incoming search terms:

HARLEY DAVIDSON HIGH PERFORMANCE CYLINDER STUD KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
This kit is designed for installation on 1986 and later XL model motorcycles. This kit is required on engines with compression ratios of 10:1 and higher. For XL 1200 engines with higher compression ratios, Screamin’ Eagle gasket kit part number 17046-98 is also recommended. Installation To protect against shock and accidental start-up of vehicle, disconnect the battery cables, negative cable first, before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious injury. 1. Disconnect the battery, negative cable first. 2. Remove top end heads and cylinders according to Service Manual instructions. Cylinder studs that are bent, scratched or broken must be replaced. Broken and bent studs distort clamp load, while scratches produce stress risers that may eventually lead to broken studs. Distorted clamp load causes head gasket leakage that may result in engine damage. Do not use a ratchet or breaker bar to install cylinder studs because they will bend the studs. 3. Remove existing cylinder studs according to Service Manual instructions. 4. Install new studs, Loctite end first. • Place a 0.313 inch DIAMETER BALL, HD Part Number 8860 (or from the XL clutch release mechanism) into the head bolt recess. Thread the stud into the head bolt until the stud bottoms on the ball. NOTE Pack clean shop towels into the crankcase openings to prevent the ball from falling into the flywheel compartment when removing the head bolt. • Clean the threads in the crankcase. • The studs have a Loctite patch on the crankcase end threads.Install the studs in the crankcase with the Loctite patch side down. • Use a T-handle to install the studs. Install studs until the free length is 4.84 ±.05 inches. See Service Manual for more detailed information. 5. Check all studs for proper height. 6. Reinstall the top end heads and cylinders according to the Service Manual Instructions