HARLEY DAVIDSON EFI INTAKE MANIFOLD COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. See Figure 1. Remove screw (A) that holds the air cleaner cover (B) and seal (C). 2. Remove three T27 TORX® screws (D) to release the cover bracket (E) from the filter element (F). 3. Remove the filter element, pulling the two breather tubes (G) from hole on the inboard side of element. 4. Remove the two breather tubes (G) from the fittings on the two cylinder head breather bolts (I). 5. Remove the two breather bolts (I) and O-ring seals (K) from the air cleaner backplate (J) with a 7/16 inch deepwell socket. 6. Remove the backplate and gasket (H) from the injection module. 7. Aligning the flat edge of a new cover gasket (2) with the backplate molded tab, install a gasket (2), chrome cover (1) and second gasket, in order, on the air cleaner back- plate. 8. Install the breather bolts through the air cleaner backplate. Re-install O-ring seals onto each breather bolt. Install a washer (3) from the kit on each breather bolt. Apply Loctite 243 to the breather bolts and align holes in the backplate with the holes in the cylinder heads and install the breather bolts. Use a 7/16 inch deepwell socket and alternately tighten the breather bolts to 120-144 in-lbs (13.6-16.3 Nm) . 9. Slide gasket over the sleeve on the inboard side of filter element. 10. Install breather tubes about 1/4 inch (6.4 mm) into holes on inboard side of filter element. 11. Install breather tubes onto fittings of two cylinder head breather bolts. NOTE Air cleaner mounting without installation of the breather tubes allows crankcase vapors to be vented into atmosphere in violation of legal emissions standards. 12. Place the filter element onto backplate, with the flat side down, so that the hole on the inboard side of element fits over the molded boss in the backplate. 13. Align holes in cover bracket with those in filter element and start three screws. Stamp on cover bracket points downwards. Use a T27 TORX drive head, alternately tighten screws to 20-40 in-lbs (2.3-4.5 Nm) . 14. Make sure that the rubber seal is proper seated around perimeter of air cleaner cover and place cover on back- plate. 15. Fit the air cleaner cover onto backplate. Apply Loctite 243 to the threads of air cleaner cover screw. Install screw through cover and tighten to 36-60 in-lbs (4.1-6.8 Nm)

Incoming search terms:

HARLEY DAVIDSON FLHRS SADDLEBAG LOCK SET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
INSTALLATION 1. Lay a clean pad or blanket on the work surface to protect the saddlebag leather surfaces. 2. Open the saddlebag lid. Remove the saddlebag from the motorcycle, leaving the lid open. See SADDLEBAG REMOVAL in the Service Manual. Lay the saddlebag flat on the pad or blanket with the inboard side facing up and the lid furthest from you. 3. See . Obtain the templates (10) from the kit. Lay the correct (left or right) template in the upper rear corner of the hard plastic inboard face of the saddlebag. Fit the template around the rear of the lid hinge and against the curve of the raised surface in the middle of the saddlebag, and tape it into place. is03044 Figure 1. Template Placement (Left Side Shown) 4. Drill four 3/16 (0.19)-inch holes in the saddlebag inboard face where indicated on the template. 5. Drill four 5/32 (0.15)-inch holes in the saddlebag inboard face as indicated on the template. 6. Remove the template. Cut out the area in between the four smaller holes to create a rectangular opening for the lock arm. Stand the saddlebag upright, with the cover open. 7. See the Figure 2. Obtain one lockset (1) and two screws (5) from the kit. Position the lockset to the saddlebag as shown, with the actuator rod protruding through the rectangular opening cut in step 6. Insert the screws through the lockset mounting holes and into the saddlebag. 8. Position a backing plate (3) over the screw threads inside the saddlebag. Fasten the lockset and backing plate to the saddlebag with two lockwashers (6) and hex nuts (7) from the kit. 9. Using a 3/16-in. hex wrench, remove the two screws holding the inside cover over the existing pushbutton lid release. Remove the cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) NOTE Make sure you are using the correct retaining-ring pliers. Verify that tips of pliers are not excessively worn or damaged. 10. Remove the retaining ring fastening the lid release cable to the pushbutton. Unhook the cable from the pushbutton lever, and pull the cable sheath out of the retaining channel on the inboard wall of the saddlebag. Remove the flat washer from the cable end. Do not discard the retaining ring and washer. 11. Trim about one inch (25 mm) from the rearmost part of the retaining channel, and re-insert the cable into the channel so the free end is at the rear of the saddlebag. 12. Insert the cable end through the hole in the backing plate, and slip the washer over the end of the cable fitting. Insert the cable into the slot in the lockset actuator rod so the ball on the end of the cable fits into the depression.

Incoming search terms:

HARLEY DAVIDSON FL SOFTAIL REAR BRAKE LEVERS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2011

download
REMOVAL 1. See Figure 1. Remove the cotter pin (5) and washer (E) from the master cylinder clevis pin (B). Discard the cotter pin. NOTE The clevis pin has a slight interference fit. It may be necessary to use pliers to pull the clevis pin from the push rod. Be careful not to damage mating parts. 2. Remove the clevis pin (B) from the brake rod. Thoroughly clean and examine parts for wear. Replace if necessary. 3. Remove the brake lever mounting screw (A) and flat washer (D), and save for reinstallation, if necessary. Remove and discard the outer O-ring (2). 4. Remove the brake lever by rotating counter-clockwise and lifting the master-cylinder clevis if necessary. Pull the lever from the shaft. Remove and discard the inner O-ring. 5. Thoroughly clean the lever mounting shaft of grease and dirt. INSTALLATION NOTE These levers are equipped with self-lubricating bushings. It is not necessary to lubricate the mounting shaft or bushings inside the lever prior to installation. 1. See Figure 1. Insert the new O-rings (4) on either side of the lever bushings (2). Install the new brake lever (1) onto the mounting shaft. NOTE There is insufficient clearance to install the clevis pin from the outside, so it must be installed from the inboard side of the brake lever. 2. Align the holes in the lever and brake rod and insert the stock clevis pin (B) from the inboard side. 3. Install the small flat washer (E) onto the clevis pin and insert the new cotter pin (5). 4. Place the large flat washer (D) onto the brake lever mounting screw (A). Apply Loctite 243 (blue) to the threads of the screw, and reinstall into the brake lever mounting shaft. Tighten the screw to 12-16 ft-lbs (16.3-21.7 Nm) . 5. Install the brake pedal pad (C) to the brake lever. After repairing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) 6. Check the brake lever for proper operation and clearance through its full travel

Incoming search terms:

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

HARLEY DAVIDSON ENGINE-GUARD FOOTPEG BILLET MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
INSTALLATION 1. See Figure 1. Position a footpeg mount (3) and clamp (1) on the engine guard. Position the footpeg mount (3) to allow the footpegs to fasten on the inboard side of the engine guard. 2. Apply LOCTITE® 243 (blue) to two screws (4). 3. Use the screws from Step 2 to fasten the footpeg mount in a comfortable location on the engine guard. Tighten screws to 14 ft-lbs (19 Nm) . 4. Install a footpeg, sold separately, using the spring washer (2), and bolt and locknut (from kit 94133-01). Position the spring washer inside the footpeg mount with the square edge toward the inside of the mount. Tighten locknut to 19 ft-lbs (26 Nm) . 5. Repeat Steps 1-4 on the other side of the motorcycle. SERVICE PARTS

HARLEY DAVIDSON LOCKING GLOVE BOX DOOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. Unsnap the original equipment (O.E.) left-side glove box door, and unfasten the tether by bringing the aglet end (see Figure 1, B) out through the retaining hole. Always wear proper eye protection when drilling or grinding. Flying debris could cause serious eye injury. (00402e) 2. Using an 3/16 inch (5 mm) bit positioned in the center of each snap, drill out the four plastic snaps surrounding the glove box opening. NOTE The glove box door, hinge and frame assemblies are side- specific. The assemblies install so that the tether retaining hole (C) in the door frame is to the inboard side. 3. Obtain the new left-side glove box door, hinge and frame assembly (1), a lock (2) and a tether assembly (8) from the kit. Remove the nut (3) from the lock. 4. Insert the lock through the hole in the glove box door as shown. Assemble the tether over the lock threads with the tab (A) on the inboard side of the lock, same as the retaining hole in the door frame. Tighten securely. 5. Open the left-side door, and position the door assembly at the glove box opening, lining up the holes. 6. Insert a screw (9) through each of the holes in the door frame and glove box. Install a hex nut with washer (10) onto the threads of each screw. Tighten finger-tight. NOTE Ambient temperature should be at least 60° F (16° C) for proper adhesion of the gaskets to the glove box door frame. 7. Clean the glove box door frame with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. NOTE The glove box gaskets are side-specific. With the paper backing facing the door frame, the oblong hole at the top of the gasket is to the outboard side. 8. Obtain the left-side gasket (6) and a hinge gasket (7) from the kit. Install the gaskets to the glove box door frame. a. The gasket liner on the large gasket is split to aid alignment. Peel one half of the liner from the adhesive backing of the left-side gasket. b. Using the frame edges and screw heads as a guide, carefully position the gasket to the glove box door frame and press firmly into place. c. Peel the remaining half of the liner from the gasket backing, and carefully position the rest of the gasket to the door frame. Press firmly into place. d. Apply steady pressure for a few seconds at all areas of the gasket to verify proper adhesion. e. Peel the liner from the hinge gasket. f. Carefully position the gasket to the door frame above the hinge, and press firmly into place.

Incoming search terms:

HARLEY DAVIDSON SADDLEBAG RAIL BRACKET KIT INSTALLATION ISNTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation 1. See Figure 1. Remove two stock screws and nuts from one side of the saddlebag rail assembly. 2. See the Service Parts illustration. Insert two screws (3) through the screw holes from the opposite direction as the stock screws removed from the rail bracket in Step 1. 3. Place a spacer (2) on the outboard screw. 4. Place a Saddlebag Rail Bracket over the rail assembly. Position the bracket with the square notch on the inboard side of the rail assembly. 5. Fasten the screws from step 2 into the Saddlebag Rail Bracket. Torque the fasteners to 10 ft-lbs (13.5 Nm). 6. Repeat steps 1 – 5 for the saddlebag rail assembly on the other side of the motorcycle

Incoming search terms: