2003 Honda ST1300lA OWNER'S MANUAL

0

Filed Under (Honda) by admin on 24-04-2011

download
Gauges & Indicators Lights when engine oil pressure is low enough to cause engine damage. If the indicator lights, pull safely to the side of the road. See page 162 for instructions and cautions. Lamp Check. PGM-FI malfunction indicator lamp (red) low oil pressure indicator (red) Lights when there is any abnormality in the PGM-FI (Programmed Fuel Injection) system. Should also light for a few seconds and then go off when the ignition switch is turned ON and the engine stop switch is at RUN. If the indicator comes on at any other time, reduce speed and take your motorcycle to a Honda dealer as soon as possible. Lamp Check. anti-lock brake system (ABS) indicator (red) ABS (ST 1300A) Lights when there is any abnormality in the anti-lock brake system (ABS). Normally, this indicator comes on when the ignition switch is turned ON, and goes off after you ride the motorcycle at a speed above 6 mph (10 km/h)If the indicator comes on while riding, stop the motorcycle in a safe place and turn off the engine. Refer to ABS indicator, page 61. For information about ABS, see page 60. LampCheck Use this button for the following purposes. To adjust time To adjust display illumination Use this button for the following purposes. To adjust time To select and reset the fuel mileage meter To change the mileage units for the odometer/tripmeter and available driving distance Use this button for the following purposes. To adjust time To select and reset the tripmeter

HONDA CT 70 Owner's Manual

0

Filed Under (Honda) by admin on 23-04-2011

download
INSTRUMENT AND INIHCATOH LAMP Speedometer I) is located on the headlight case and odometer 2′. incorporated in the speedometer indicates total distance travelled. Gear speed range indicators l’_§t‘- are Curved bare shown on the Epeeciometer dial plate to indicate the recommended operating range of the respective gears. High beam indicator lamp tredi i is located at the right side of the speedometer. This lamp will he on when headlight is on high beam. mph
‘.1_ Speedometer -fgi Odometer -Ffij Gear speed r.|nge indicators L @ High boom indicator lamp I “5′ Page 13 I  ELECTRICAL CONTRUIB I lGilTIUi’~l SWIICH The ignition switch is located on the left side of the main pipe. Functions of the respective 5″.’t'lt’C|’t positions are shuvvn in the chart helovv. t lgtttttttn sti, |tch Kev position I unction ii] OFF Slfitigiertzttrical circuit I5 opened, engine ‘t.’t.’||| not I3. Electrical circttit is closed, engine can be started {for day time operattioni 4 Eiectrical circuit is closed, engine can be “-3 started {for night time operation? Key removal Key can be
removecl Kev can not be removed Kev can not he removed age 14 10 0 HEADLILIHT BEAM CDH’TROL SWITCH The headlight beam control switch {D is located on the left handle grip. “L” is low beam position llow beam light and tail light on]. “H” is high beam light and tail light on. The headlight will only operate when the ignition switch is in the on posi- tion. Reler to ignition switch page 9.eat “$2, i 1| ma‘ ‘ aw Lg; Headlight beam contxul switclr -”‘ @ “I.” position {ii “ll” position , ._ _. i HORN BUTTON This is a push button switch Q) to-zated on the right handte grip. When the horn button switch is depressed the horn wlll operate

Oil Pressure Gauge Set Installation

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
7. See Figure 3-4 . Assemble banjo bolt (3), washer (4), OIL PRESSURE GAUGE (1) banjo fitting and second washer onto adapter and tighten snugly. 8. Temporarily secure oil pressure gauge and hose to motorcycle frame with cable straps. Make sure gauge and hose assembly do not interfere with normal operation of the vehicle. Start engine and ride motorcycle at least 20 miles (32 km) at or above 50 mph (80 km/h) to allow engine to reach operating temperature. a. At 2500 RPM, oil pressure will vary from 10-17 psi (69-117 kN/m2). b. At idle speed (950-1050 RPM), oil pressure will vary from 7-12 psi (48-83 kN/m2). NOTE For an accurate reading, engine oil should be at normal operating temperature: 230°F (110°C). 9. Stop engine. Remove OIL PRESSURE GAUGE assembly from oil pressure indicator lamp switch mounting hole in crankcase. Cut cable straps that you installed in step 8. above, and remove banjo bolt, gauge assembly, washers and adapter from vehicle. 10. See Figure 3-2 . Coat threads of oil pressure switch (2) with LOCTITE 565 HIGH PERFORMANCE PIPE SEALANT with TEFLON. Reinstall oil pressure switch. Using OIL PRESSURE SENDING UNIT WRENCH, tighten switch snugly. DO NOT OVERTIGHTEN. 11. Plug in connector [120] (3) by pushing elbow connector straight up onto stud on oil pressure switch. 12. Install voltage regulator caddy and attach DC output connector and neutral switch wiring harness to caddy. See 7.28 MAIN WIRING HARNESS . NOTE If an appreciable amount of oil leaked out when oil pressure switch was removed, it will have to be replaced with fresh oil. 13. Check oil level in oil tank. See 1.5 ENGINE OIL AND FILTER . Top off oil level if necessary. 14. Start engine and test oil pressure switch for proper operation. Check oil pressure switch for leaks.

Incoming search terms:

2007 Ural Retro Model Installation Manual

0

Filed Under (Ural) by admin on 02-11-2010

download
Kickstart lever : Designed to start the engine. Upon kicking the lever the crankshaft is actuated through the gearbox. The lever is returned to its initial position by the spring inside the gearbox. Gear shift lever: This is a heal shift type of lever. To shift up from a low gear to a high gear the rear arm(heal shift) is pressed. To shift down from a high gear to a low gear the from arm is depressed. Since the heel-toe shift lever is short-coupled, it is much easier to shift up using the heal shift, and to shift down using the toe shift with the ball of your foot. The neutral gear is between the 1st and 2nd gears. It is important to shift smoothly with a constant force, and not to kick the gear shift pedal. Serious damage may result to the shifting mechanism if the gear shift pedal is kicked, rather than pressed urn indicator lamp indicates that the turn signals are activated. Alternator fault indicator lamp , indicates that the charging system is malfunctioning and needs immediate attention. Gearbox neutral lamp indicates that the gearbox is in neutral. Head lamp high beam indicator , indicates that the headlight high beam is activated. Speedometer is on the dash board, with trip and total odometer. The trip odometer is reset to zero by rotating knob (Fig.1, # 3) counterclockwise. Note that the odometer reads in kilometers