YAMAHA FZS6W OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
Indicator and warning lights EAU11030 Turn signal indicator lights “ ” and “ ” The corresponding indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light This indicator light comes on when the transmission is in the neutral position. EAU11080 High beam indicator light This indicator light comes on when the high beam of the headlight is switched on. EAU11250 Oil level warning light This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. NOTE: ● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. ● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle. EAU11423 Coolant temperature warning light “ ” This warning light comes on when the engine overheats. When this occurs, stop the engine immediately and allow the engine to cool. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir

Yamaha TW200N/ TW200NC SPECIFICATIONS AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EAS00017 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head pipe. EAS00018 MODEL CODE The model code label 1 is affixed to the frame. This information will be needed to order spare parts CABLE ROUTING 1 Throttle cable 2 Front brake light switch lead 3 Right handlebar switch lead 4 Clutch cable 5 Left handlebar switch lead 6 Clutch switch lead 7 Front turn signal/position light lead (left) 8 Main switch lead 9 Indicator lights lead 0  Speedometer cable A Meter light lead B Headlight coupler C Wire harness D Front turn signal/position light lead (right) E Brake hose ب Fasten the brake hose with a plastic locking tie to the brake hose grommet. ة Fasten the wire harness with a plastic locking tie PERIODIC CHECKS AND ADJUSTMENTS INTRODUCTION This chapter includes all information necessary to perform recommended checks and abjustments.If followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work.This information applies to vehicles already in service as well as to new vehicles that are being prepared for sale.All service technicians should be familiar with this entire chapter. PERIODIC MAINTENANCE CHART FOR EMISSION CONTROL SYSTEM

2003 Honda ST1300lA OWNER'S MANUAL

0

Filed Under (Honda) by admin on 24-04-2011

download
Gauges & Indicators Lights when engine oil pressure is low enough to cause engine damage. If the indicator lights, pull safely to the side of the road. See page 162 for instructions and cautions. Lamp Check. PGM-FI malfunction indicator lamp (red) low oil pressure indicator (red) Lights when there is any abnormality in the PGM-FI (Programmed Fuel Injection) system. Should also light for a few seconds and then go off when the ignition switch is turned ON and the engine stop switch is at RUN. If the indicator comes on at any other time, reduce speed and take your motorcycle to a Honda dealer as soon as possible. Lamp Check. anti-lock brake system (ABS) indicator (red) ABS (ST 1300A) Lights when there is any abnormality in the anti-lock brake system (ABS). Normally, this indicator comes on when the ignition switch is turned ON, and goes off after you ride the motorcycle at a speed above 6 mph (10 km/h)If the indicator comes on while riding, stop the motorcycle in a safe place and turn off the engine. Refer to ABS indicator, page 61. For information about ABS, see page 60. LampCheck Use this button for the following purposes. To adjust time To adjust display illumination Use this button for the following purposes. To adjust time To select and reset the fuel mileage meter To change the mileage units for the odometer/tripmeter and available driving distance Use this button for the following purposes. To adjust time To select and reset the tripmeter

HARLEY DAVIDSON FLHT RADIO AND GAUGE FACEPLATE TRIM INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
This kit fits 1996 and later FLHT models. Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE The instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents Table 1. Kit Contents Part Number Description 74612-06 Radio and gauge faceplate trim There are no Service Parts available with this kit. INSTALLATION NOTE Mounting surface of faceplate trim must be above 60°F (16°C), or the trim may not stay attached. 1. Using a 50:50 isopropyl alcohol/water solution, thoroughly clean the surface where the faceplate trim will be installed. Do not clean with denatured alcohol, mineral spirits, or other solvent products, or damage to the radio may occur. (00411b) 2. Allow the surface to dry completely before continuing to install kit. 3. Test the fit of the faceplate trim prior to removing adhesive backing. 4. Remove the adhesive backing from the back of the faceplate trim. 5. See Figure 1. Install the faceplate trim, locating it upward as far as possible. This position will align the opening in the faceplate trim with the indicator lights. NOTE If you do not position the faceplate trim properly, this may prevent proper clearances between the CD door and trim for 2006 and later models. 6. Let the adhesive cure for at least 24 hours at no less than 60°F (16°C). is01435 Figure 1. Indicator lights properly aligned through faceplate NOTE For models earlier than 2006, the installation is complete after the faceplate trim is installed.

DRAG SPECIALTIES MINI SPEEDOMETER WITH LED INDICATOR LIGHTS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Place the motorcycle on a level and secure area. Disconnect the battery. 2. Refer to the appropriate factory service manual and remove the OEM speedometer and indicator lights. The indicator lights usually unplug either in the rear of the headlight or under the gas tank area. 3. Mount the new speedometer in the desired location. 4. Locate the OEM wire for the high beam indicator light. Connect it with the blue wire from the wire harness on the speedometer. Connect the blue/black wire from the speedometer to ground. 5. Locate the OEM wire for the gauge illumination (back) lighting. Connect this wire to the orange wire on the speedometer. Connect the black wire on the speedometer to ground. 6. Locate the OEM wires for the turn signals. Usually they are brown and violet wires. NOTE: You will notice only one bulb for the turn signals in the gauge and two wires from the bike to the harness. If you connect both of these wires directly to the yellow wire on the speedometer, this will allow feedback and cause all the signals to flash at once. To prevent this, you will need to add a diode between each OEM turn signal wire and the yellow wire coming from the speedometer. We recommend that you utilize a Dyna tach adapter, Part #D-101, available separately. This tach adapter includes the diodes necessary to allow the turn signal indicator light to operate correctly. Follow the instructions for the tach adapter, substituting the wires from the original wire harness found in step 6 for the two ignition terminals shown in the wire schematic. Hook the white wire on the tach adapter to the yellow wire for the turn signal indicator on the speedometer. If you use the D-101 adapter, skip steps 7-9 and go directly to step 10. 7. Take one of the diodes, making sure to observe the correct polarity, and attach it to the brown turn signal wire on the bike. 8. Take the remaining diode, again making sure to observe the correct polarity, and attach it to the violet turn signal wire on the bike

Incoming search terms:

DUCATI SUPERBIKE 848 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
Position of the motorcycle controls (fig. 3) 1) Instrument panel. 2) Key-operated ignition switch and steering lock. 3) Left-hand handlebar switch. 4) Clutch lever. 5) Rear brake pedal. 6) Right-hand handlebar switch. 7) Throttle twistgrip. 8) Front brake lever. 9) Gearchange pedal. 1 4 3 2 9 8 5 7 6 fig. 3 11 E Instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are about 3 litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. It may come on briefly if the engine is very hot, but should goout again as engine speed increases. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “Engine diagnostics light” ( amber ). The engine ECU illuminates this light steadily to indicate the presence of errors leading to engine lock. 9) “Motorcycle diagnostics” light . Illuminates when the motorcycle diagnostics detects a problem. 10) Rev limiter indicator lights . Indicator light 10A: illuminates steadily at 800rpm before intervention of the rev limiter. Indicator lights 10A + 10B: illuminate steadily 400rpm before intervention of the rev limiter. Indicator lights 10A + 10B + 10C: start flashing when the rev limiter is reached. 2 1 5 9 8 6 3 4 5 7 10B 10C 10A fig. 4 12 E 11) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 12) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for theLAP and USB data aquisition functions.

DUCATI MONSTER 696 Owner's manual and maintenance manual

0

Filed Under (Ducati) by admin on 14-12-2010

download
instrument panel (fig. 4) 1) LCD (see page13). 2) Tachometer (rpm). Indicates engine revs per minute. 3) Neutral (N) indicator ( green ). Illuminates when the gearbox is in neutral. 4) Fuel warning light ( yellow ). Illuminates when there are approximately 3litres of fuel left in the tank. 5) Turn signal indicator light ( green ). Illuminates and flashes when the turn signal is in operation. 6) Engine oil pressure warning light ( red ). Illuminates when engine oil pressure is too low. This light should illuminate when the ignition is switched to ON and should go out a few seconds after the engine starts. Important If this light (6) stays on, stop the engine to avoid serious damage. 7) High beam warning light ( blue ). Illuminates when the high beam headlight is on. 8) “EOBD engine diagnostics light” ( amber ). The engine ECU iluminates this light steadily to indicate the presence of errors leading to engine lock. 9) OVER REV indicator lights . Illuminates steadily at 800 rpm before intervention of the revlimiter. Starts flashing when the rev limiter is reached. 5 8 2 4 9 3 1 6 7 fig. 4 12 E 10) 2-position switch A and B . Switch used for displaying and setting instrument panel parameters. It has two positions, A “▲” and B “▼”. 11) High beam headlight flasher switch (fig. 5). The high beam headlight flasher switch is also used for the LAP and USB data aquisition functions. 11 A 10 B fig. 5 13 E LCD – Main functions Warning Any adjustments to the instrument panel must only be carried out when the motorcycle is stationary. Never operate the instrument panel controls while riding the motorcycle. 1) Speedometer . Indicates road speed. 2) Odometer . Shows total distance travelled. 3) Trip meter . Indicates the distance travelled since last reset. 4) Fuel reserve trip counter . Shows distance travelled on reserve fuel. 5) Clock . 6) Air temperature indicator . 7) Lap time . 8) Rev counter (RPM) . 9) Lap time . 8 11 13 12 14 10 4 5 9 6 2 3 1 7 fig. 6 14 E 10) Service indicator (fig. 6). The indicator illuminates to signal when a service is due. The service indiactor will remain on the display until the system is reset by the Ducati Service Centre who carry outthe service. 11) LAP function (fig. 6). Indicates that the LAP has been activated. 12) DDA function (fig. 6). Indicates that the Ducati Data Analyzer (DDA) has been activated. Important The instrument panel incorporates diagnostic functions for the electronic injection/ignition system. The relative menus are for the use of trained personnel only. If you accidentally access this function, turn the key to OFF and have the motorcycle checked at an authorised Ducati Service Centre. 13) Oil temperature indicator (fig. 6). Important Stop riding if the temperature reaches the maximum value, otherwise the engine might be damaged. 14) Ducati Traction Control (DTC) (fig. 6). Indicates activation of the DTC control unit (if present). 15 E LCD – How to set/display parameters At key-on (key turned from OFF to ON ) the instrument panelactivates all the digits of the LCD for 1second and switches on the indicator lights in sequence.

Incoming search terms:

1995 HONDA VFR Owners Manual

0

Filed Under (Honda) by admin on 01-12-2010

download
INSTRUMENTS AND INDICATORS The indicators are contained in the instrument panel. Their functions are described in the tables on the following pages. USA model: Odometer and tripmeter read in miles. Canadian model: Odometer and tripmeter read in kilometers. (1) Speedometer (2) Odometer (3) Left turn signal indicator (4) Side stand indicator (5) High beam indicator (6) Digital clock (7) Tachometer (8) Tachometer red zone (9) Neutral indicator (10) Right turn signal indicator (11) Fuel indicator (12) Fuel gauge (13) Coolant temperature gauge (14) Low oil pressure indicator (15) Tripmeter (16) Tripmeter reset knob 15 (Ref.No.) Description Function ————————————————- ———————————————————– (1) Speedometer Shows riding speed. (2) Odometer Shows accumulated mileage. (3) Left turn signal indicator (Amber) Flashes when the left turn signal operates. (4) Side stand indicator Lights when the side stand is put down. Before parking, check that the side stand is fully down; the light only indicates the side stand ignition cut-off system (page 54) is activated. (5) High beam indicator (Blue) Lights when the headlight is on high beam. (6) Digital clock Shows the time (page 19). (7) Tachometer Shows engine RPM. (8) Tachometer red zone Shows excessive engine rpm range in which operation may damage the engine. (9) Neutral indicator (Green) Lights when the transmissions in neutral. (10) Right turn signal indicator

Motorcycle Alarm X60 Userʼs Manual

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
REMOTE START Press the button twice within two seconds and hold, engine will start automatically, and used for keyless driving and warm-up. Repeat the above operation if the engine does not function due to cold weather or due to slow rotation of engine. NOTE: when using the remote start up, the switch key of the motorcycle cannot be pressed at the same time, otherwise the fuse will blow. How to turn off the remote start function: press the button once then engine will stop. ANTI HOTWIRE When system in armed mode if system detects the ignition is forcibly switched on (hotwired) siren will activate and indicator lights will remain solid, the engine is automatically immobilised and motorcycle cannot be started up. The siren will sound for 30 second if the ignition is switched off, otherwise it will sound continuously. ANTI HIJACK Press the button and button at the same time when ignition is on engine will immobilise immediately, siren will sound continuously and indicator lights will flash continuously. Press the button to de-activate anti hijack mode. VALET MODE In disarming mode, IGNITION OFF position, turn IGNITION ON/OFF 6 times and stopped at ON at the last time, then press button within 5 seconds. LED will be on constantly, indicating system entered into Valet Mode. In this mode, all alarming function disabled. Only remote engine start and bike finding function. Follow the same procedures to exit Valet Mode

Incoming search terms:

YAMAHA XT500E, XT600E SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
INSTRUMENT AND CONTROL FUNCTIONS 3 ON OFF LOCK . EAU00040 LOCK The steering is locked, and all electrical systems are off. The key can be removed. To lock the steering 1. Turn the handlebars all the way to the left. 2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it. 3. Remove the key. To unlock the steering Push the key in, and then turn it to “OFF” while still pushing it. 12 1. Push. 2. Turn.
3-2 INSTRUMENT AND CONTROL FUNCTIONS 3 EAU00056 Indicator lights EAU00063 High beam indicator light ” & ” This indicator light comes on when the high beam of the headlight is switched on. EAU00061 Neutral indicator light “N” This indicator light comes on when the transmission is in the neutral position. EAU00057 Turn signal indicator light ” 5 ” This indicator light flashes when the turn signal switch is pushed to the left or right. 12 3 1. High beam indicator light “&” 2. Neutral indicator light “N” 3. Turn signal indicator light “5 ” EAU00095 Speedometer unit The speedometer unit is equipped with a speedometer, an odometer and a tripmeter. The speedometer shows riding speed. The odometer shows the total distance traveled. The tripmeter shows the distance traveled since it was last set to zero with the reset knob. The tripmeter can be used to estimate the distance that can be traveled with a full tank of fuel. This information will enable you to plan future fuel stops