2001 – 2003 Highlander FRONT DOOR OPENING WEATHERSTRIP

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
have been improved to better resist deformation or tearing at the bottom center portion of the front door frame. Replace the front door opening weatherstrips on vehicles with this condition built prior to the VIN breaks listed in the Production Change Information section below. 2001 – 2003 model year Highlander vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE TYPE PRODUCTION CHANGE EFFECTIVE VIN 4Cylinder 4×2 JTEGD21A#30052511 Highlander 4 Cylinder 4×4 JTEHD21A#30020710 Highlander 6Cylinder 4×2 JTEGF21A#30085273 6 Cylinder 4×4 JTEHF21A#30113260 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 62311-48020-## Same Weatherstrip, Fr Door Opening, RH 1 62312-48020-## Same Weatherstrip, Fr Door Opening, LH 1 Replace the front door opening weatherstrip as shown in the Technical Information System (TIS). Refer to the 2001 – 2003 Highlander Repair Manual; Exterior/Interior Trim, Roof Headlining Assembly

Incoming search terms:

2002-2003 HONDA GL1800 BANK ANGLE SENSOR MOUNTING SCREWS REPAIR MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
REPAIR PROCEDURE 1. Insert the ignition key into the lock cylinder and open the fairing pocket lid by turning the key clockwise. Remove the two trim clips by pushing the cen- ter pins in. Remove the two screws. Disconnect the opener  cable and remove the right fairing pocket. 2. To access the bank angle sensor, remove the two mounting screws  securing the connector holder. Place the holder to the side. 3. To check for the proper screw size, slightly tighten both bank angle sensor screws. If the screws are tight, reassemble the unit and apply the identification mark. If the screws spin in the holes, proceed to Step 4. 4. Using a magnetic screwdriver, remove and discard one of the two 4 mm screws securing the bank angle sensor assembly. Replace with a 5 x 12 mm self-tapping screw (see the PARTS INFORMATION section on page 3 for the proper screw for this repair). Repeat for the other screw. 5. Reinstall the removed parts in the reverse order of removal. IDENTIFICATION Apply a white paint dot in the center of the under- side of the right fairing pocket lid as shown. This will indicate that the Safety Recall has been per- formed on this unit

Incoming search terms:

2002-2003 GL1800 BANK ANGLE SENSOR MOUNTING SCREW REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Insert the ignition key into the lock cylinder and open the fairing pocket lid by turning the key clockwise. Remove the two trim clips by pushing the center pins in. Remove the two screws. Disconnect the opener cable and remove the right fairing pocket. 2. To access the bank angle sensor, remove the two mounting screws securing the connector holder. Place the holder to the side. 3. To check for the proper screw size, slightly tighten both bank angle sensor screws. If the screws are tight, reassemble the unit and apply the identification mark. If the screws spin in the holes, proceed to Step 4. 4. Using a magnetic screwdriver, remove and discard one of the two 4 mm screws securing the bank angle sensor assembly. Replace with a 5 x 12 mm self-tapping screw (see the PARTS INFORMATION section on page 3 for the proper screw for this repair). Repeat for the other screw. 5. Reinstall the removed parts in the reverse order of removal. IDENTIFICATION Apply a white paint dot in the center of the underside of the right fairing pocket lid as shown. This will indicate that the Safety Recall has been performed on this unit

Incoming search terms: