Harley Davidson Shift leverbracket INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2012

download
Installation of any parts should be performed by a qualified, trained mechanic. • All parts included in the Rocker Boards™Conversion Kit are intended to be used as sold. Modification of any part will void all warranties. • Installation should be performed on a motorcycle that is completely cool to avoid burns or other injuries. • Refer to a specific authorized Harley-Davidson service manual for correct disassembly and reassembly procedures for any parts that need to be removed to facilitate installation. • Motorcycle exhaust fumes are toxic and poisonous and must not be inhaled. Always run motorcycle in a well-ventilated area. • Do not perform any installation steps under the influence of alcohol, drugs, or if feeling fatigued. Warranty Briggs Made Cycle Parts, Inc. Rocker Boards™and all parts included in the conversion kit are warranted to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of one (1) year from the original date of purchase. Any part that fails to conform to these conditions, will be repaired or replaced at the discretion of Briggs Made Cycle Parts, Inc. upon receipt of the defective part within the one year warranty period. In the event a part has been rendered defective, Briggs Made Cycle Parts, Inc. must be notified prior to the return of the defective part. Briggs Made Cycle Parts, Inc. will not be liable for any consequential or incidental damages resulting from the failure of any part, the breach of any warranties, the failure to deliver, delay in delivery or any other breach of duty between Briggs Made Cycle Parts, Inc. and a customer

Yamaha R1 2007-2008 Frame Slider Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Installation Steps: 1. Remove left and right body panels. 2. Remove the left side engine stud. Mount the left side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the left side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 3. With the offset in the correct position remove body and torque down to OEM torque specs. 4. Using one drop of blue thread locker mount the left side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 5. Remove the right side engine stud. Mount the right side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the right side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 6. With the offset in the correct position remove body and torque down to OEM torque specs. 7. Using one drop of blue thread locker mount the right side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 8. Mount left and right bodywork

Incoming search terms:

Kawasaki ZX10R 2008 Frame Slider Installation And Removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
installation Steps: 1. Remove right side bolt. Mount right side puck with (99-HB-SH10125060) Socket Cap 10 X 1.25 X 60 Main Engine Stud and torque down. 2. Remove left side mid panel. 3. Locate the left side engine stud and remove bolt. 4. Some photos in this section are used for illustration examples only. It is up to you how you decide to cut your motorcycles bodywork to accept the frame slider there are many different ways customers go through this process. Shogun is not responsible for any part of your motorcycle for any reason. Precisely measure location of cut and if in doubt at any point please call us before the install process has begun. Professional installation is recommended. Always use proper safety measures during the install of this product. Do not try to install this product without proper tools, recently calibrated torque wrench, correct torque specifications from factory service manual, safety goggles and gloves. 5. Body Prep. Use masking tape to completely mask off the area on the body where you will be working. We usually will tape off approximately 6 to 8 inches around the though hole area and any other edges that could get bumped or scratched while working. Tip: In some locations you may want to double up the thickness of the masking take to give extra protection

Harley-Davidson EMERGENCY DRIVE BELT REPLACEMENT KIT Installation Manual

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Shift transmission to neutral. Before installation of the emergency belt, to avoid personal injury and/or vehicle damage, secure the motorcycle. Both stand and motorcycle must be on solid, level ground. Failure to follow instructions could result in death or serious injury. 2. See Figure 1. Remove spring clip (4) (if present) and loosen rear axle nut (1). 3. Loosen rear axle adjuster (3) (or adjuster nut, if so equipped) on each side of motorcycle, and move rear wheel to full forward position. 4. Remove the damaged/broken belt. 5. Inspect sprockets and belt guard (2) for damage and/or debris. Remove any debris. If sprockets and belt guard are not damaged, proceed with the installation. 6. Remove belt guard. 40171-97,40146-00 1 WARNING i06186 Figure 1. Axle 1. Axle nut 2. Belt guard 3. Adjuster 4. Spring clip 2 4 1 3 7. See Figure 2. Install feeder strip on emergency belt. 8. Feed strip around transmission sprocket in a counterclockwise direction over frame cross support. 9. See Figure 3. Interlock the “v” ends of the emergency belt. a. Insert a hex socket key in the fourth (4) and ninth (6) tooth holes. b. Place the splice block (2) over the seventh (5) tooth hole. c. Install a socket head set screw (3) in the seventh tooth. Tighten using another hex socket key. d. Move the block to the next tooth, and repeat installation steps (b) and (c) in each tooth until all 12 screws are installed. NOTE There are 16 screws included in this kit. However, only 12 screws will actually be installed in the belt. The remaining four screws are spares. 10. See Figure 4. Grasp the emergency belt at the mid point of the lower run between your thumb and forefinger and lift the belt up to take up any slack in the belt. Measure the distance that the belt deflects (2) under tension (1). When two pounds of tension is applied to the lower run of the emergency belt, the belt deflection should be within the following measurements

Incoming search terms: