HONDA TRX 400EX Removing Stock Carb and Cables INSTRUCTION

0

Filed Under (Honda) by admin on 21-12-2011

download
Remove seat/fender assembly and fuel tank. 2. Remove throttle cables paying close attention to routing. 3. Remove thumb throttle housing if you are installing a twist throttle. 4. Remove air box and air box intake tube. 5. Remove stock carburetor. 6. Stuff a clean rag into intake manifold to keep debris from entering engine. Preparing machine for carburetor installation 1 . Route the provided throttle cables per manufacturer’s recommended procedure, routing them the same as the stock cables. 2 . Remove the rubber alignment tabs from the manifold using a razor blade or cutters. Be very careful not to damage the intake manifold! 3. Remove air box intake tube from the air box and use a hacksaw to cut approx. 1½” off of the air box intake tube. Your tube should resemble the one shown in Figure 1. Re-assemble the air intake tube into air box and install back onto bike. Don’t forget to tighten clamp around intake tube and reinsert crank vent into the air boot. Figure 1. Thumb Throttle Attach cable into cable wheel with the cable end at the 8: 00 position of the cable wheel, then into bracket. Secure by replacing the cable bracket end and phillips screw. See Figure 2. Figure 2. Twist Throttle 1. Install the pull (see figure 4 for cable identification) , cable end into the 8: 00 position and the idle cable end into the 11: 00 position on the cable wheel. See Figure 3

Toyota 2006-10 Yaris L4-1.5L NTAKE TUBE, THROTTLE BODY AND ENGINE REMOVAL AND INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
turn the ignition OFF and disconnect the vehicle’s negative battery cable. NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE. 2. Depress the locking tab and remove the mass air sensor connector. Remove the clips that secure the mass air sensor har- ness to the stock air box. 3. Pull the vacuum switching valve and bracket assembly from the stock intake tube. Un-clip the vacuum hose from the stock intake tube. 4. Loosen the spring clamp that secures
the crank case vent tube to the stock intake tube as shown. Remove the crank case vent tube from the stock intake tube. Note: The spring clamp will be re-used. 5. Loosen the hose clamp that secures the stock intake tube to the throttle body as shown. Remove the stock intake tube from the throttle body

HARLEY DAVIDSON DECORATIVE TRIM FOR HEAVY BREATHER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
INSTALLATION NOTES To avoid exposure to grease, oil, dust, dirt and skin oil, do not remove the backing film from the medallion or medallion insert until the moment of application. For maximum adhesive bond, the intake tube surface under and immediately surrounding the medallion must be clean and dry. 1. Clean the surface of the intake tube with a mixture of 50- 70 percent isopropyl alcohol and 50-30 percent distilled water. Allow to dry thoroughly. NOTE Ambient temperature should be 70-100 °F (21-38 °C). 2. See Figure 1. Remove backing film from medallion insert (1) and install on medallion (2). 3. With the backing film still in place, trial fit the medallion (2) to the intake tube. 4. Remove the backing film from the back of the medallion. Press the medallion firmly into position for about five sec- onds. 5. After releasing pressure, avoid direct contact with the medallion for at least 20 minutes. NOTE Allow AT LEAST 24 hours before exposing the air cleaner to vigorous washing, strong water spray or extreme weather. The adhesive bond will increase to maximum strength after about 72 hours at normal room temperature

BMW 3 SERIES INSTALLATION MANUAL

0

Filed Under (BMW) by admin on 17-11-2010

download
1. Turn off the ignition and disconnect the negative battery cable. NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft code to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code. TO START: 2. Depress the wire-locking clip and disconnect the mass air sensor electrical. BMW 3 SERIES (E46) 1999-00 323i, ci 1999 323iC 2001-05* 325i, ci L6-2.5L 1999-00 328i 2000 328ci 2002-05 325xi L6-2.8L NOTE: * Excluding 2003 & 2005 PZEV model with engine family 3BMXV02.5M56 & 5BMXV02.5M56 Flat Blade Screwdriver Ratchet Extension 10mm Socket 10mm Wrench 4mm Allen A intake tube (EL) 1 087139 B hose ; 4mm id x 2″ l 1 08062 C npt fi tting; 1/4″ x 5/16″ barb 1 08908 D hose clamp #48 3 08601 E silicone hose 3.25″id x 2″l 1 08690 F nut; 6mm nylock 7 07553 G washer; 1/4″id x 5/8″od fl at 7 08275 H washer; 1/4″ split lock 1 08198 I bolt; 6mm-1.00 x 16mm, b/h/a 2 07730 J bolt; 6mm-1.00 x 12mm, b/h/a 4 07794 K washer; 1/4″id x 1″od fender 2 08160 L bracket 1 010087 M heat shield “A” 1 07492 N heat shield “C” 1 07497 O heat shield “B” 1 07494 P edge trim 46″L 1 102487 Q air fi lter 1 RU-4730 3. Pull up on the four fresh air duct-retaining pins to release them from the radiator core support. 4. Lift up and remove the fresh air duct from the vehicle as shown. NOTE: Disconnect the fresh air tube from the fresh air duct. 5. Loosen the hose clamp which secures the intake tube to the mass air sensor, and then disconnect the intake tube from the mass air sensor as shown. 6. Remove the two-factory air box mounting bolts shown.

BMW R1100RT FUEL Plus kit INSTALLATION Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
Remove the following components to prepare for installation. There will be some differences between models and years. Remove both seats. Remove both left and right side fairing panels. Remove the bolt at the right rear of the fuel tank (if needed) to run the display cable to the left side of the frame (inboard of the air intake tube) along the factory wiring harness. Disconnect the negative battery cable (and any additional ground wires) at the battery. Remove the air intake tube from the air box. 3. Install the wiring. NOTE: The # indicates the connection to the unplugged 16 pin terminal strip. See the table. The Junction Board will be mounted on top of the air box just in front of the air temperature sensor. PHOTO1 An alternate position is shown in PHOTO 1A. The clear sleeve for the board gets stiff when it is cold. Warming makes it more pliable. If it is difficult to get the air sensor connector back on then use the alternate position on the left. The wiring enters the upper left corner for either position

HARLEY DAVIDSON 2008-2009 FLHR, FLHRC, FLHT, FLHTC FLHTCU, FLHX, FLTR 1584CC INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Start the engine with the transmission in neutral or park. Listen for air leaks or odd noises. For air leaks secure hoses and connections. For odd noises, fi nd cause and repair before proceeding. This kit will function identically to the factory system except for being louder and much more responsive. 2. Test drive the vehicle. Listen for odd noises or rattles and fi x as necessary. 3. If road test is fi ne, you can now enjoy the added power and performance from your kit. 4. K&N Engineering, Inc., suggests checking the air fi lter element periodically for excessive dirt build-up. When the element becomes covered in dirt (or once a year), service it according to the instructions on the Recharger® service kit, part number 99-5050 or 99-5000. ROAD TESTING: • 1455 CITRUS ST., P.O. BOX 1329, RIVERSIDE, CA., U.S.A. 92502 • TECH SERVICE 800-858-3333 • FAX 951-826-4001 • e-mail: tech@knfi lters.com® • WWW: http://www.knfi lters.com® 10. Install the provided K&N® air fi lter and secure with the provided hose clamp. A black hose clamp is being supplied with kit. This clamp is intended to clamp the fi lter to the intake tube. NOTE: The K&N® high fl ow intake system is a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must install the K&N® Drycharger® onto the air fi lter.