1990 Harley Davidson ULTIMA 6 SPEED BUILDERS KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-04-2012

download
For 2000 & later models removal of approximately 1/4 of an inch off of the shifter arm bushing is likely required. Doing so will allow installation of the retaining clip & washer onto the shifter arm. It is good practice to double check how much material should be removed before cutting the bushing. See fig. 1 & 2 Install supplied Main drive gear bearings & countershaft needle bearings using special tool # 97-164 NOTE: Lightly coat bearings with assembly lube or gear oil for easier installation. Install supplied Main drive gear retaining clip & verify that it is fully seated and cannot come out. Do not re-use old bearings or retaining clip. Install supplied Main drive gear into bearings using special tool # 97-166 See fig. 3 Install supplied trap door gasket & verify that it is on correctly. Install supplied 6 speed gear set making sure to align the countershaft with the needle bearing assembly. Slowly slide in gear set until the mainshaft & countershaft will not slide in any further. Lightly tapping on the trap door (while verifying that there is no interference) with a soft blow hammer will then fully seat the shafts & trap door. See fig. 4 Once gear set is installed use the supplied 5/16-18×1-1/2 & 1/4-20×1-1/2 bolts to secure the trap door. Torque the 5/16 bolts to 15 ft-lbs w/ red loctite (high strength) Torque the 1/4 bolts to 9 ft-lbs w/ red loctite (high strength) See fig. 5 FIG. 1 FIG. 2 FIG. 3 FIG. 4 FIG. 5 2 FIG. 6 At this time check to make sure all gears rotate freely & that all slider gears slide with no interference. Lightly lube & install supplied quad seal onto main drive gear. See fig. 6 Install Main seal using special tool # 97-164. See fig. 7 Install original spacer onto mainshaft. NOTE: Beveled side goes in towards quad seal. See fig. 8 Install supplied transmission drain plug & supplied speedo sensor plug with gasket. Install supplied shifter forks onto appropriate slider gears. See fig. 9 Lightly lube & install supplied shift fork shafts. NOTE: Short shaft is installed from the right side with the threaded hole facing out. Long shaft is installed from the left side & should not protrude from the right side of case. See fig. 10 Install supplied shift fork shaft allen head plugs. (Use red loctite to prevent movement of plug & to aid in sealing)

HARLEY DAVIDSON ENGINE-GUARD MOUNTED FOOTPEGS (CHROME WITH RUBBER INSERT) INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
Installation Footpegs must be positioned so rider can operate all foot controls throughout their range of motion without interference. Failure to have full, unlimited access to foot controls could cause loss of control, which could result in death or serious injury. 1. See Figure 1. Remove the bolt (6) and lockwasher (5) from the footpeg assembly (1). NOTE When installing the footpegs on a 1 inch (25 mm) diameter engine guard, use both clamps. . For 1 inch (25 mm) dia. engine guards: Place both the large clamp (2) andthe small clamp (1) around the engine guard as shown. Position the clamps on the straight, upright section of the guard. For 1-1/4 inch (32 mm) dia. engine guards: Discard the small clamp (1). Place the large clamp (2) around the engine guard. Position the clamp on the straight, upright section of the guard. 2. For ALL engine guards: Install two step spacers (4) inside the clamp on either side of the engine guard as shown. 3. Put the lockwasher (5) on the bolt (6). Insert the bolt through the clamp and spacers, and thread into the footpeg assembly as shown. Mount the footpegs so they will not strike the ground during cornering. Footpegs striking the ground during cornering could result in death or serious injury. 4. Position the footpeg for rider comfort, and rotate the footpeg assembly so it folds upward and to the rear. Tighten bolt (6) to 30 ft-lbs (41 Nm) so the footpeg does not rotate on the bar. 5. Repeat Steps 1 through 4 for the right side

2006 Honda GL1800 AirbagCB Radio Squeal REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 08-04-2011

download
To remedy this problem, a ferrite core harness kit is now available for installation. 2006 GL1800 VIIIA (Airbagmodels) with optional CBRadio. Install a ferrite harness core kit according to the installation instructions that are packaged with the kit. ÒÑÌÛæ • The kit includes both a rider and a passenger harness; it’s necessary to install both harnesses to eliminate the squealing noise. • Passengers must route the headset cord as shown. If routed otherwise, it will be too close to the motorcycle’s antenna, which can create an interference. Subharness installation can be confirmed by removing the left-side fairing pocket, and check- ingtoseeifthe harness is already installed. Ferrite CoreHarness Kit (1 required) P/N: 08E95-MCA-100WA H/C: 8607665 ÒÑÌÛæCallTechLineat (800) 421-1900 to order parts. Due to the limited number of affected units and parts availability, ordering will be controlled until May 31,2007. Normal warranty claim submission require- mentsapply. Submit one claim per VIN. Template: GL19 Flat RateTime: 0.3 hours

HARLEY DAVIDSON 360 DEGREE HIGHWAY FOOTPEG MOUNTING KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Position footpegs so rider can operate foot controls without interference. Failure to have full access to foot controls can cause loss of control, which could result in death or serious injury. (00313a) Mount the footpegs so they will not strike the ground during cornering. Foopegs striking the ground during cornering can cause loss of control, resulting in death or serious injury. (00458b) NOTE See Figure 2 for steps 2 through 6. 1. Determine what height on the engine guard you prefer for the final mounting of the footpeg mounts. Mark location, if desired. 2. See Figure 2. Obtain clamp assembly (1) from kit. Wrap the clamp halves around the engine guard and install with hinge pin head facing upward. Place the flatwasher between the ears of the clamp halves. Hold parts in posi- tion. 3. Obtain the lockwasher (13), screw (7) and one of the footpeg extensions (14) (long or short depending on kit number) from kit. 4. Position the clamp adapter (10) over the clamp assembly (1) with the “cogged” face of the adapter facing the extension arm (14). Hold clamp adapter in place. 5. Install screw (7) with internal tooth lockwasher (13) through the clamps, the clamp adapter (10) and into the extension arm (14). Position extension arm as desired. Do not tighten completely at this time. 6. Obtain the clevis/extension assembly (6) from kit. Position assembly such that footpeg pivots upward and toward the rear of the bike. NOTE: It may be necessary to loosen the screw slightly and rotate the extension to obtain this position. Tighten item 9 securely. 7 5 1 3 4 2 6 8 is02511 1. Clamp assembly 2. Arm extension 3. Clevis 4. D-washer 5. Footpeg 6. Screw 7. Clamp adapter 8. Clamp halves Figure 1. 360 Degree Footpeg Mounting Installed (Shown with Footpeg Installed) NOTE The footpeg will be a tight fit if the D-spring washer is installed correctly. 7. Refer to Figure 1. Obtain the footpeg (5), sold separately, D-spring washer (4) and screw (6) from kit. Install the D- spring washer so it is positioned inside the clevis (3) with the square “D” edge towards the inside of the mount. Hold the washer in place and slide the footpeg into position. Install the screw (6) and tighten to 19 ft-lbs (26 Nm). 8. Repeat Steps 1 through 7 for the opposite side. Position the footpeg assemblies so they are at equal heights and symmetrical. Securely tighten each assembly until it cannot be rotated on the guard with reasonable foot pressure, but do not exceed 55 ft-lbs (81 Nm) on item 7

Incoming search terms:

HARLEY DAVIDSON HEEL RAISER FOOTPEG KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
INSTALLATION 1. Remove the locknuts and screws that hold the existing footpegs in place. If the motorcycle is equipped with a pin and retaining ring, remove them and retain for future use. Save all hardware for installation of the new footpegs. 2. Remove the existing footpegs and the spring washers. Save the spring washers for installation. NOTE See Figure 1. When performing the next step, verify that the spring washer is positioned inside of the footpeg support with the square edge (2) towards the inside of the support. 1 3 2 is02094 1. Spring washer 2. Spring washer square edge 3. Footpeg support slot Figure 1. Footpeg Spring Washer Installation 3. See Figure 1. Install the new footpegs in the same manner as the old footpegs were installed. Insert a spring washer (1) and the mount end of the footpeg inside the slots (3) of the footpeg supports. 4. Secure each footpeg and spring washer to the footpeg support with the screw and locknuts or pin and retaining rings removed earlier. Tighten the locknuts to 19 ft-lb (26 Nm) . Footrests must fold up and toward rear of motorcycle if struck. Failure to set footrests to fold up and back could result in death or serious injury. (00366a) Position footpegs so rider can operate foot controls without interference. Failure to have full access to foot controls can cause loss of control, which could result in death or serious injury. (00313a)

ULTIMA 6 SPEED BUILDERS KIT INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 03-03-2011

download
DISASSEMBLY For 5 speed gear set removal refer to your factory service manual. You willneed to remove the main drive gear, main drive gear bearings, retaining clip & countershaft needle bearings. NOTE: Removal of the shifter arm is notnecessary for 99 & earlier transmissions. NOTE: Removal of the shifter arm isnecessary for 2000 & later transmissions. After trans. housing is disassembled thoroughly clean & inspect. ASSEMBLY For 2000 & later models removal of approximately 1/4 of an inch off of the shifter arm bushing is likely required. Doing so will allow installation of the retaining clip & washer onto the shifter arm. It is good practice to double check how much material should be removed before cutting the bushing. See fig. 1 & 2 Install supplied Main drive gear bearings & countershaft needle bearings using special tool # 97-164 NOTE: Lightly coat bearings with assembly lube or gear oil for easier installation. Install supplied Main drive gear retaining clip & verify that it is fully seated and cannot come out. Do not re-use old bearings or retaining clip. Install supplied Main drive gear into bearings using special tool # 97-166 See fig. 3 Install supplied trap door gasket & verify that it is on correctly. Install supplied 6 speed gear set making sure to align the countershaft with the needle bearing assembly. Slowly slide in gear set until the mainshaft & countershaft will not slide in any further. Lightly tapping on the trap door (while verifying that there is no interference) with a soft blow hammer will then fully seat the shafts & trap door. See fig. 4 Once gear set is installed use the supplied 5/16-18×1-1/2 & 1/4-20×1-1/2 bolts to secure the trap door. Torque the 5/16 bolts to 15 ft-lbs w/ red loctite (high strength) Torque the 1/4 bolts to 9 ft-lbs w/ red loctite (high strength) See fig. 5

Incoming search terms:

Honda GL1100/ 1200 Saddlebag Bent Rails Installation Manual

0

Filed Under (Honda) by admin on 28-02-2011

download
Read instruction thoroughly before installing. DRILLING REQUIRED. 1. Place bike on center stand. 2. Place masking tape on feet of rail to prevent scratches on the saddlebags. Position saddlebag rails on saddlebag to mark for drilling. 3. When positioning the rail, carefully move the rail back and forth until proper alignment is achieved and there is no interference with the saddlebag latch. 4. Mark position for drilling holes on a piece of masking tape placed on the saddlebag under each leg. 5. Drill a 6mm hole. 6. Remove tape from rail and clean the saddlebag if necessary. 7. Attach the rail with the hardware included from the inside of the saddlebag lid. 8. Repeat on other side.

HARLEY DAVIDSON HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
REMOVAL See the service manual for removal procedures. INSTALLATION See the service manual and follow the wiring procedures. NOTE For Non-FXDF Models Only: See Figure 1. Cut the mesh tubing from the kit into two equal length pieces. Slide the switch wire bundles through mesh conduit. Position conduit into switch control housing. Tie each end of conduit with cable tie from kit. Handlebar Installation See the service manual and follow the installation procedures. SAFETY CHECK Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a) •Be sure wires, clutch cables, throttle/idle cables and brake lines do not pull tight when handlebars are turned fully to left or right fork stops. 1. Verify that the ignition/light key switch is turned to the OFF position. Install the main fuse. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) 2. Turn the ignition/light key switch to IGNITION, but do not start the engine. Test each handlebar switch for proper operation. Before starting engine, be sure thr ottle control will snap back to idle position when released. A throttle control that prevents engine from automatically returning to idle can lead to loss of control, which could result in death or serious injury. (00390a) SERVICE PARTS

HARLEY DAVIDSON ANGLED HIGHWAY PEG MOUNTING KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
INSTALLATION Position footpegs so rider can operate foot controls without interference. Failure to have full access to foot controls can cause loss of control, which could result in death or serious injury. (00313a) Mount the footpegs so they will not strike the ground during cornering. Foopegs striking the ground during cornering can cause loss of control, resulting in death or serious injury. (00458b) 1. Determine what height on the engine guard you prefer for the final mounting of the footpeg mounts. Mark location, if desired. 2. See Figure 2. Obtain the mounting clamp (11) from kit. Position the clamp halves around the engine guard at the desired height and install with hinge pin head facing upward. The “cogged” face of the clamp should face the extension arm. 3. Obtain the washer (5), screw (8) and one of the angled arms (11) (long or short depending on kit number) from kit. Using the screw, align and install the angled arm with washer (5) positioned between the clamp “ears”. 4. See Figure 1. Position the angled arm such that footpeg will pivot upward and toward the rear of the motorcycle. Do not tighten completely at this time. 2 3 4 1 is 02264 1. Clamp 2. Extension arm 3. Screw 4. Hinge pin Figure 1. Engine Guard Footpeg Mounting (Shown Installed with Footpeg) NOTE The footpeg will be a tight fit if the D-spring washer is installed correctly. 5. Refer to Figure 1 and Figure 2. Obtain the footpeg (sold separately), D-spring washer (10) and screw (7) from kit. Install the D-spring washer so it is positioned inside the footpeg mount (arm) with the square “D” edge towards the inside of the mount. Hold the washer in place and slide the footpeg into position. Install the screw and tighten footpeg screw to 19 ft-lbs (26 Nm). 6. Note the two small tapped holes on the back side of the footpeg mount clevis area. Install the setscrew to the lower of the two holes. The angle of the footpeg is adjusted by running the set screw in and out. Repeat Steps 1 through 6 for the opposite side. 7. Position the footpeg assemblies so they are at equal heights and symmetrical. Securely tighten each assembly until it cannot be rotated on the engine guard with reasonable foot pressure but do not exceed 55-60 ft-lbs (75-81 Nm) on item 8

HARLEY DAVIDSON TOUR-PAK WALL ORGANIZER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
This kit fits 1997 and later models equipped with King Tour- Paks INSTALLATION NOTE Maximum Wall Organizer weight capacity is 3 pounds (1.4 Kg) evenly distributed. Do not exceed tour-pak weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00401b) Tour-Paks With Molded Liner 1. Remove the two nuts that hold the pouch and liner in the Tour-Pak. Remove pouch and liner and carefully wash the inside of the Tour-Pak with warm, soapy water. Rinse and dry thoroughly. 2. Use the alcohol prep pad in the kit to thoroughly clean the interior surface of the Tour-Pak sides where fastener strips will be attached. Make sure any residue is removed, then allow Tour-Pak to dry completely. Make sure the surface is free of condensed moisture. NOTES The hook and loop fastener strips and organizer must be installed below the edge of Tour-Pak base to avoid interference with top gasket and lock. The ideal temperature range for applying the fastener strip is 70-100° F (21-38° C). Minimum application temperature is 50° F (10° C). If you attempt to apply the tape below these temperatures, the adhesive will become too firm to adhere readily. 3. See Figure 1 and Figure 2. Remove the hook and loop fastener strips from the hinged hook and loop strips. Remove the paper backing and firmly press the fastener strips into the locations (1) shown in Figure 2. The fastener strips should be located approximately 1/8 in. (3 mm) below the edge of the Tour-Pak base. 4. See Figure 1. Bend the hinged hook and loop strips (3) into shape as shown. Attach the hinged strips onto the fastener strips (2) installed in Step 3. NOTE The Tour-pak Wall Organizer installs in place of the pouch removed in Step 1, therefore the pouch will not be re-installed. 5. Reinstall the liner removed in Step 1. The hinged strips (3) will go over the top of the liner (4) as shown in Figure 1. 6. See Figure 1. Attach the organizer (5) to the hinged strips (3). Adjust the organizer’s lock cut out so that it is centered around the lock, and press the hook side of the hook and loop strips on the bottom of the organizer into place on the liner. The hook side will attach to the liner. NOTE 2006 and later Tour-Paks equipped with Passenger Backrest will have two acorn nuts at the front of the base. Remove and discard the 8 in. (200 mm) long hook and loop hinged fastener strip from the center panel. In one of the organizer pockets there will be 4 in. (100 mm) and 1-1/2 in. (38 mm) hook and loop hinged fastener strips. Install the hinged strips on the organizer center panel as shown in Figure 3. 7. Check to make sure the Tour-Pak lid closes over the organizer and the lock works without interference. Adjust as necessary. 8. Allow tape to cure (“wet-out”) for a minimum of 48 hours at 70° F (21° C) (allow extra time if temperature is below 70°). Do not place items in the Wall Organizer while adhesive is curing

Incoming search terms: