Honda CBR 954 RR Undertail Kit INSTALLATION

0

Filed Under (Honda) by admin on 04-12-2011

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting.
2) Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos to the above and below. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary. Honda CBR954RR Undertail Kit (2002-03, Available in: Honda Red, Gloss Black and Gun Metal) 3) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts. 4) Insert undertail left side first, then right side, be carefully not to crack
or scratch undertail. Use your stock plastic screw rivets to hold under- tail in place. Tighten all hardware on tail section, attach seat.
5) Using clips, splice your turn signal wires to the signals in the undertail. On the bike; the orange wire is the the left turn, light blue wire is the right turn and the green wires are the grounds. On the undertail the red wires are the power wires and the black wires are the ground. * After this modification your undertail is not returnable. Paint is not warrantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray. Need Help? If you need additional help with the installation of the undertail, go to www.hotbodiesracing.com and look for the “FAQs” link at the bottom of the home page. Most of your general questions can be answered on those pages. This installation does require a basic mechani- cal aptitude, if in doubt, contact your local motorcycle shop and have a professional mechanic perform the installation, 3 hours is the average installation time

Incoming search terms:

Honda RC51 2000-2005 SBK Undertail Kit INSTALLATION

0

Filed Under (Honda) by admin on 22-11-2011

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos to the above and below. Your subframe may be different but the cutting position is the same on all years. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary Replace all bodywork with fasteners loosely installed, mount undertail,
notice at bottom of the tray there are 2 holes, mark and remove tray, then drill holes in battery box 6) Inset lock into undertail using stock lock mounting clip, make sure the lock is in the correct position with the lock cable arm to function
properly. Insert undertail left side first, then right side, be carefull not to crack or scratch undertail. Use your stock plastic screw rivets to hold undertail in place. Attach lock cable to lock, check movement, adjust if necessary. Tighten all hardware on tail section, attach seat. * After this modification your undertail is not returnable. Paint is not war-
rantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray.
6) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts

2000 Lexus RX 300 DOOR LOCKS, TRUNK LID & FUEL DOOR – POWER

0

Filed Under (Toyota Manuals) by admin on 28-05-2011

Download

All doors can be locked and unlocked from either front door using control switch or door key. When you unlock driver’s door with door key, if you turn key once, only driver’s door will unlock. If you turn key twice within 3 seconds, all doors will unlock. KEY CONFINEMENT PREVENTION SYSTEM If driver leaves key in ignition, opens door, then tries to lock doors using control switch (on door panel), system will not allow doors to be locked. This prevents key from being locked inside

Incoming search terms: