Ktm 950 SMR Installation and Removal Manual

0

Filed Under (KTM) by admin on 27-01-2012

download
Be sure the triple clamp in your kit has a part # 3012R- 27 -6-0208 on the bottom side. This is very important. 2. Warning: Once the triple clamp is loose, the forks can roll away from the bike . Block it up properly to start with. 3. Block the front tire securely before removing the top triple clamp, so the tire cannot move forward. It’s best to tie the forks up to something above you, like the rafters, using tie downs, or a tie down from the front axle up and over the frame backbone and then underneath the lower triple clamp. Once the forks start to come off while working, it’s extremely difficult to get them back together without help. Block the back wheel up also, so it puts pressure on the front end, forcing it to stay in position. Spend the time setting this up correctly and your installation will go easier. 4. This kit requires removal of the headless “Security” bolts that hold the key switch in place. These bolts will need to be drilled out in order to remove them, pictures below. Removal is fairly easy, if you follow these instructions. 5. Examine all the wire and cable routing before removal and make notes of where everything goes. 6. Remove 2 bolts that hold the headlight shroud in place. Be careful not to lose the small bushings that fall out easily. 7. Follow the wire from the ignition switch to the wire loom in the headlight shroud and unplug it. There is no locking tab on this plug so you can usually undo it without having to disassemble the wiring. 8. Remove the 4 bolts that hold your bars tight and lay the bars forward out of the way (Bungie or tie to the front of bike). 9. Be sure the front end is securely blocked or tied to something above the bike. Remove the top triple clamp, taking note of how tight the 27mm main nut is, so you can re-tighten to the exact tension for the bearing. The main nut merely provides the correct tension on the head tube bearing, so the tension is critical. The nut will NOT be tight coming off. Once the fork and triple clamp pinch bolts are loose, the main nut can be removed. It’s difficult to get a wrench on the main nut. We were able to sneak the stock KTM axle wrench in there, otherwise, you may have to loosen the lower bar perches using an 8mm Allen wrench and a 17mm socket for the underside nuts. Once the main nut is off, lift the triple clamp off carefully , trying not to disturb the blocked-front-wheel. A rubber mallot is helpful here

Incoming search terms:

HARLEY DAVIDSON BOOM! AUDIO BASS BOOSTER TOUR-PAK PORT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
PREPARATION NOTE For vehicles equipped with security siren: • Verify that the Hands-Free Fob is present. • Turn the ignition key switch to IGNITION. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the owner’s manual and follow the instructions to remove the main fuse. INSTALLATION NOTE The Tour-Pak does not need to be removed from the vehicle to perform this installation. 1. Open the Tour-Pak lid and remove all items from the Tour- Pak base. 2. Models equipped with mat: Remove the mat. Models equipped with liner: Open the map pocket, and remove the acorn nuts with flat washers. Remove the map pocket and liner. 3. Remove four screws from the left-side speaker grille on the Tour-Pak. Remove the speaker grille from the speaker pod. 4. Remove the speaker from the speaker pod. Carefully pull the two socket terminals from the speaker spade contacts. 5. Remove the grommet, and draw the rear speaker/passenger controls connector out of the speaker pod. Separate the connector halves. 6. Repeat Steps 3 through 5 for the right-side speaker. 7. See Figure 1. Get the drill template (3) from the kit. If NOT equipped with power port: a. Remove one speaker pod mounting screw and flat washer. b. Align the drill template on the inside of the Tour-Pak with the speaker pod holes, and hold in place with the mounting screw and washer. c. Repeat for the remaining template mounting holes. If equipped with power port: a. Remove the two screws and flat washers to free the power port from the Tour-Pak. b. Align the drill template on the inside of the Tour-Pak with the power port holes, and hold in place with the mounting screws and washers. c. Repeat with the top speaker pod mounting screw and flat washer. NOTE Tighten the screws enough to hold the speaker pod in place as the pilot hole is drilled. 8. Where indicated on the template, drill a 3/16 inch (5 mm) diameter pilot hole through the Tour-Pak wall and speaker pod. 9. Remove the screws and speaker pod, and set aside. Turn the template over, and repeat Steps 7 and 8 on the left side of the Tour-Pak. NOTE Hole size will affect the fitment of the ports. The hole saw needs to be sharp. 10. Carefully drill a two inch (51 mm) diameter hole with a sharp hole saw, at the pilot location, through each speaker pod and in both locations on the Tour-Pak wall. 11. Temporarily install the Tour-Pak liner (if equipped), and mark the location of the two inch (51 mm) diameter holes on the outside of the liner. Remove the liner, and carefully cut the two holes in the liner front wall

Incoming search terms:

HARLEY DAVIDSON HANDLEBAR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
REMOVAL See the service manual for removal procedures. INSTALLATION See the service manual and follow the wiring procedures. NOTE For Non-FXDF Models Only: See Figure 1. Cut the mesh tubing from the kit into two equal length pieces. Slide the switch wire bundles through mesh conduit. Position conduit into switch control housing. Tie each end of conduit with cable tie from kit. Handlebar Installation See the service manual and follow the installation procedures. SAFETY CHECK Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a) •Be sure wires, clutch cables, throttle/idle cables and brake lines do not pull tight when handlebars are turned fully to left or right fork stops. 1. Verify that the ignition/light key switch is turned to the OFF position. Install the main fuse. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) 2. Turn the ignition/light key switch to IGNITION, but do not start the engine. Test each handlebar switch for proper operation. Before starting engine, be sure thr ottle control will snap back to idle position when released. A throttle control that prevents engine from automatically returning to idle can lead to loss of control, which could result in death or serious injury. (00390a) SERVICE PARTS

HARLEY DAVIDSON CHROME LOWER BELT GUARD INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the Maxi® Fuse. 2. See Figure 1. Remove the three screws with captive washers (3) securing the original equipment (O.E.) lower belt guard (debris deflector, Item 1) to the underside of the rear fork (2), and set them aside for re-use. Remove and discard the lower belt guard. 3. Position the new chrome lower belt guard in place on the underside of the rear fork, lining up the three holes in the belt guard with the mounting holes in the fork. Insert the three screws saved earlier through the holes in the belt guard, and thread them into the fork. Tighten the screws to 36-60 in-lbs (4.1-6.8 Nm) . 4. Verify that the Ignition/Light Key Switch is turned to the OFF position. Refer to the Owner’s Manual and follow the instructions given to re-install the Maxi® Fuse. 2 1 3 is04766 1. Lower belt guard (debris deflector) 2. Rear fork (swingarm) 3. Screw with washer (3) Figure 1. Lower Belt Guard Installation

2004-UP DIGITAL SPEEDOMETER MODULE Owner's Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
SPEEDOMETER INSTALLATION The following procedure details the removal of the factory speedometer and installation of the digital speedometer on Softail models; however the process is similar for all other models: 1. Remove the nut and washer (item #4 in the accompanying exploded view) that secures the console (#5) to the fuel tank. 2. Lay a clean shop rag on the fuel tank and flip the console over to expose the underside of the console. 3. Separate the 12-pin harness connector (#2) from the speedometer. 4. Unscrew the rubber cover from the “trip” reset switch (#6) on t left side of the console. he 5. Remove the “trip” switch from the console. 6. Pry between the three tabs that hold the back clamp (#7) to the speedometer (#1). Remove the back clamp from the speedometer. 7. Remove the speedometer from the console. 8. Remove the gasket (#3) from the speedometer. 9. Installation is the reverse of removal. CHAPTER 3 SPEEDOMETER OPERATION When the motorcycle key switch is ON, the speedometer will enter “normal” mode. Pressing the MODE button will cycle through the following display options: Odometer (ODOM) displays the mileage since the speedometer was installed. Trip (TRIP) displays the mileage since the last time the “trip” button was pressed. Head Temp (H TEMP) displays the cylinder head temperature in degrees F. Battery V (BATT V) displays the battery voltage Fuel (FUEL) displays the fuel level in gallons. Miles Per Gallon (MPG) displays the fuel economy in miles per gallon. Range (RANGE) displays the calculated range (in miles) until the tank reaches its empty value. Horsepower (POWER) to perform the horsepower test, follow these steps

Baja BA 250 ATV OWNER'S MANUAL

0

Filed Under (Bajaj) by admin on 26-11-2010

download
FUEL AND OIL FUEL Proper fuel is very important for the engine. Ensure there is no dust, dirt, or water which has mixed in the fuel. Use regular unleaded gasoline with an octane number 90 or higher. ENGINE OIL Your 250cc ATV has a four-stroke engine. Please use oil as described in the chart below. By using prescribe oil, you will realize the best lubrication for engine. Use the chart to select a viscosity rating based on the temperature range in your area. NOTE: In very cold weather (below 5°F (-15°C), use SAE10W-30 for good starting and smooth operation. SAE 10W-30 SAE 20W-40 ENGINE TEMP. °C °F -30 -22 40 104 -10 14 0 32 10 50 20 68 30 86 -20 4 FUEL AND OIL 8 LOCATION OF LABELS Read and follow all of the warnings labels on your ATV. Make sure you understand all the labels. Keep the labels on the ATV. Do not remove them for any reason. If a label comes off or becomes difficult to read, you should get a replacement by contacting BAJA INC. 1 – Red Light – Reverse indicator Light illuminates when ATV is in Reverse. 2 – Green Light – Neutral indicator Light illuminates when ATV is in Neutral. 3 – Ignition key switch – Turn right (CW) “RUN”, Turn left (CCW) “OFF”. ATV will only start when ignition key is turned to the “RUN” position. Make sure ignition key switch is in the “OFF” position when not in use

Incoming search terms:

Installation Instructions S&S Billet Air Cleaner Kit for Victory Motorcycles

0

Filed Under (S&S) by admin on 29-10-2010

download
1 – Disconnect the negative battery cable from the motorcycle and route it away from any metal parts in the area. 2 – Remove the seat and gas tank from the Victory motorcycle following your Victory service manual for the specifi c model you are performing the work on. Picture 1 WARNING 3 Key Switch Cover and Coil Mounting Bracket Removal 1 – Remove the ignition key switch cover by pulling outward on it. Picture 2 illustrates the key switch cover. 2 – Remove the four socket head cap screws from the ignition and coil mounting bracket that holds the bracket to the front and rear heads. Picture 3 points out the location of the four socket head cap screws. 3 – With the bracket free from the front and rear head unplug the spark plug wires at the coil. 4 – Disconnect the coil and ignition switch at the connectors freeing them from the primary wiring harness. Idle Air Control Hoses and Throttle Position Sensor Removal 1 – Disconnect the Throttle Position Sensor (TPS) at the connector leaving the TPS attached to the throttle body. Picture 4 points out the TPS connector. 2 – Remove the Idle Air Control (IAC) supply hose from the air box. Note: Leave the 1.500″ rubber hose attached to the hard plastic IAC supply hose. Picture 4 points out the IAC air supply hose and the 1.500″ rubber hose. 3 – Remove the front Idle Air Control (IAC) air delivery hose from the rubber 90° fitting that leads into the front intake bore on the throttle body. Leave the 90° rubber fitting attached to the throttle body. Picture 4 points out the IAC front delivery hose. 4 – Remove the rear IAC air delivery hose from the rubber “T” fitting that leads into the rear intake bore on the throttle body. Leave the rubber “T” fitting attached to the throttle body. Picture 4 points out the IAC rear delivery hose

1999-2001 DUCATI Monster INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
It is essential to use Blue Loc-tite on all nuts and bolts. Remove any other steering stabilizers. 2) Cover the tank with an old sweatshirt or protective device so you don’t scratch it. 3) General concept for this mount: The new key cover is the anchor point for the stabilizer, so it must be fitted correctly as per the instructions below. The base of the new key cover must sit flush all the way around to provide the support needed. The bolt lengths are critical, so be sure you read the instructions carefully so you know which bolts go in which spots! 4) Remove the (4) 8x85mm Allen bolts that hold your handlebars tight. There are plastic plugs in the tops of these bolts that must be removed before you can access the Allen head. Replace the stock top barclamp with the one provided in the kit. 5) Tighten the 4 bolts evenly so the gaps between upper and lower perches, front to back, are even. 6) Remove the (2) 6x12mm Allen bolts and the plastic key cover that covers your key switch. 7) Fit the new billet aluminum key cover over the key switch and be sure the new cover is sitting down flush all the way around on the frame. It needs to be touching the frame to function properly. We’ve machined this part to fit precisely on the bike but each bike can vary slightly due to machining variations from the Ducati Factory. The new key cover should center itself by locating on the 2 spacer/nuts underneath. You might need to loosen the 2 bolts on the underside of the frame to allow those spacer/nuts to find their centering point on our key cover. 8) Note: Your stock key switch itself has a casting knub near its base that could restrict our new cover from sitting all the way down flush. We’ve machined a clearance notch inside our part for this knub to fit into, but it is possible it could vary from bike to bike, which might require a bit more clearance filing. Be sure the key cover is sitting down flush against the frame. 9) We’ve machined the key cover to fit over a 20mm spacer nut / .805″. If for some reason the stock “spacer/nuts” are too tall, you may have to file them slightly to allow the Billet key cover to sit down flush and touch the frame. 10) Once the key switch cover is flush against the frame, all the way around it’s base, retighten the bolts that hold the spacer/nuts secure from the under side of the frame using Loc-tite. Reinstall the (2) 6x12mm stock key cover bolts to a maximum of 6-ft/lbs . The stock key cover bolts are designed to engage 6mm of thread in the spacer nut. Do not be tempted to use any longer bolts than 6x12mm or they can prematurely bottom out which will keep the key cover from tightening. Shorter than 6×12 or if the cover is not flush, makes it possible to damage the threads. Double check these key-cover bolts after your first ride, as they may loosen after initial movement from the damper

Incoming search terms:

Incoming search terms: