2007 KTM 250 XC-F, XCF-W, EXC-F 400 XC-W, EXC RACING 450 XC, XC-W, EXC RACING 525 XC, XC-W, EXC RACING 525 XC DESERT RACING INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 05-02-2012

download
Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button Pushing the black starter button [2] will actuate the E-starter. Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on. ENGLISH 7 2 Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 3 4 5 6 1 OPERATION INSTRUMENTS » ENGLISH 8 TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode

Incoming search terms:

2005 Honda CRF450X OWNER'S MANUAL AND COMPETITION HANDBOOK

0

Filed Under (Honda) by admin on 04-12-2010

download
Starting & Stopping the Engine Always follow the proper starting procedure described below. Your CRF can be started with the transmission in gear by pulling in the clutch lever before operating the kickstarter or start button. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 5. Warm up the engine; don’t operate the throttle. 6. About 15 seconds after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. HighAirTemperature 35°C (95°F) or above 1. Turn the fuel valve (1) ON. 2. Do not use the choke. 3. Keep the throttle fully closed. 4. Start the engine following step 4 under “Normal Air Temperature.” LowAirTemperature 10°C (50°) or below 1. If the temperature is below 32°F (0°C), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 2. Follow steps 1-5 under “Normal Air Temperature.” 3. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. (cont’d) NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for”High Air Temperature.” NormalAirTemperature 10°C-35°C (50°F-95°F) 1. Turn the fuel valve (1) ON. 2. Pull the choke knob (2) fully ON, if the engine is cold. 3. Keep the throttle fully closed. 4. Pull the clutch lever all the way in, and depress the start button. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine

Incoming search terms:

2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms:

Incoming search terms: