KTM EXC / MXC DUAL SPORT KIT REMOVAL AND INSTALLATION

0

Filed Under (KTM) by admin on 25-01-2012

download
Using a small phillips head screwdriver, loosen the locking screw ( B ) on the kill switch ( C ). Remove any cable ties and unplug kill switch from existing wiring. Step 2 Loosen clutch cable perch ( D ) and move inboard about 1/2 inch. Important Note Regarding Magura Brakes The KTM uses the Magura hydraulic brake, which may cause potential interference between the turn switch and the lever adjuster. Make sure you have enough clearance between the parts. You can either move the grip out slightly, or take a file and sand away a small notch in the turn switch where it may rub. Install Turn Switch Step 1 Open and wrap the new turn switch ( E ) around handlebar and securely fasten with two screws ( F ) as shown. Make sure you have clearance between the grip, the switch and the lever! Step 2 Route turn switch wiring down and along handle bar behind Dakar headlight unit and in through frame cable guide. Secure switch wiring to handlebars with one cable tie. For more information, please refer to the Cable Routing Diagram

HONDA XR 250 1996 Dual Sport Kit Installation Manual

0

Filed Under (Honda) by admin on 06-12-2011

download
Get a degree in Mechanical and Electrical Engineering. (Just kidding!) 2. Remove the seat, side panels, radiator shrouds, and gas tank.
If you are color blind or even think you might be a little color blind, now is the time to get someone to assist you. Successful installation of the kit requires good color recognition. You want to go riding this weekend, don’t you? 3. Unplug the green and blue taillight wires from the stock wiring harness, remove the taillight lens, and remove the taillight socket and wiring. 4. Unplug the headlight from the stock wiring harness and remove. 5. Remove the kill switch. Unplug the black/white wire and the black wire from the connector near the base of the odometer. AC Regulator Unplug taillight here Photo 1 6. Locate the AC voltage regulator found mounted on the front top edge of the airbox as shown in Photo 1. Unplug the regulator from the wiring harness and remove regulator (Leave the U-bolt
attached to the airbox and save the bolt for a later step)

BMW F650 GS Rider's Manual

0

Filed Under (BMW) by admin on 27-11-2010

download
General viewsHandlebar fitting, right 1 Emergency off switch (kill switch) (52) 2 Starter button (65) 3 GripheatingOE (53) 4 Flashing turn indicators, right (50), Hazard warn- ingflashers (51) 5 Cancel button, flashing turn indicators (51), Pushbut- ton, cancel hazard warning flashers (52) 2 17 z General views Instrument cluster 1 Telltale lights (22) 2 Speedometer 3 Operation of the clock (42), Operation of the stopwatchOE (46) 4 Multifunction display (22) 5 Operating the odometer (42) 6 Telltale light, anti-theft alarm (OE), Sensor for instrument lighting, Warning light for enginerpmOE (48) 7 Rev. counter The instrument-cluster lighting has automatic day and night switchover. 2 18 z General views Headlight 1 Low-beam headlight 2 High-beam headlight 3 Sidelight

Suzuki DRZ400E Dual Sport Kit Installation Manual

0

Filed Under (Suzuki) by admin on 23-11-2010

download
1. Remove the seat, side panels, and fuel tank. Kill switch connector Photo 1 2. Unplug and remove the stock headlight. 3. Unplug and remove the stock kill button. See Photo 1. 4. Unplug and remove the stock taillight. Using a utility knife, trim the taillight mounting tabs flush with the underside of the fender. 5. Taillight Installation: Attach the provided LED taillight to the under side of the rear fender using the provided countersunk mounting hardware as shown in Photo 2. Route the taillight wires forward to the area on top of the airbox along the right side of the fender. Secure the taillight wires to the taillight plastic with zip-ties so the tire cannot make contact. Photo 2 6. Rear Turn Signal Installation: Attach the rear turn signals to the flat portions on the sides of the LED taillight. Position them so they are out of the path of the exhaust. Route the wires forward securing with zip-ties. Route the right turn signal wires and the taillight wires around the front of the muffler mount and between the fender and the black plastic splashguard as shown in Photo 3.