2004 KTM 250 EXC-R exhaust system INSTALLATION

0

Filed Under (KTM) by admin on 07-02-2012

download
1. Remove the rear shock and the standard exhaust pipe. And attach the rear shock again. (Standard exhaust flange should remain the current position) 2. Lightly attach the front exhaust pipe to the engine. (See Photo. 2) 3. Insert the joint and tail pipe to lightly attached front exhaust pipe in step 2. Shake the whole for the better fitting. Then, attach the supplied springs to the joint. Lightly attach this tail pipe with the standard bolt. *Insert the two inner collars to the joint. 4. Lightly assemble the silencer and the silencer stay. Insert this to the tail pipe. Lightly attach this tail pipe to the standard attachment position with supplied bolt and collar. Check the best position for the silencer band. (See Photo. 3) 5. Remove the silencer attached in step 4. Securely fasten the bolt of the silencer band. Insert this silencer to the tail pipe and lightly fasten the bolt of the stay. 6. Securely attach the tail pie followed by the silencer stay. 7. Attach supplied springs to the joint of the silencer. 8. Clean all surfaces. Remove any oil on the exhaust pipe and silencer. 9. Make sure all bolts and nuts are securely fastened. Run the engine and ensure there are no exhaust gas leaks. (See Photo. 4) *Carburetor adjustment will be required in the weather and course

2007 KTM 250 XC-F, XCF-W, EXC-F 400 XC-W, EXC RACING 450 XC, XC-W, EXC RACING 525 XC, XC-W, EXC RACING 525 XC DESERT RACING INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 05-02-2012

download
Headlamp switch (XC-W) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button Pushing the black starter button [2] will actuate the E-starter. Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on. ENGLISH 7 2 Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 3 4 5 6 1 OPERATION INSTRUMENTS » ENGLISH 8 TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode

Incoming search terms:

2007 KTM 250, 450, 505, SX-F QPX Performance Tip/ Spark Arrester Clean out Procedure

0

Filed Under (KTM) by admin on 24-01-2012

download
Step 1: Take off the end cap of exhaust by removing the five (5) screws using a T-20 torx wrench. Cut the silicone around stock end cap using a box knife, then pull cap straight off. Step 2: Step 3: To install your new QPX Performance Tip/Spark Arrester, slide QPX assembly into muffler with engraving on base right side up. Step 4: Align holes of QPX base and muffler, then reinstall the five (5) original screws with your T-20 torx wrench. Installation is now complete. Store instructions in a safe place for future reference. (See clean out instructions on reverse.) If the spark arrester screen isn’t already installed in the QPX Performance Tip, remove the four (4) M6 bolts attaching the cone to the base, remove cone, install screen between base and cone, reinstall M6 bolts and tighten. Do NOT tighten. Start, but leave loose until all screws are started, the tighten securely.

Incoming search terms:

2004-2005 KTM 250/ 400/ 450/ 525 Side Panel Fuel Tank removal and Installation Instructions

0

Filed Under (KTM) by admin on 22-01-2012

download
1. Remove airbox cover. Drill stock rivet nut in frame tube through with a ¼” drill as shown in Photo 1. Drill completely through frame tube. We suggest you make a small guide hole in the top of the frame tube first so that you drill straight through the frame member and not come out the side of the frame tube. Photo 1 .Install Lower mounting bracket as shown in Photo 3 noting its orientation. Install the aluminum cone into the recess at the bottom of the stock airbox , then bolt the bracket on with the 6 x 70 mm bolt. Nylock nut threads to top of bolt on top of frame tube as shown in photo 2. Photo 3 2 3. Install the upper mounting bracket shown in Photo 4. Note that in either the MXC or the EXC installation four to six of the 6 x 18 mm fender washers should be installed between the bracket and the subframe. The counter-sunk hole should be positioned toward the rear wheel. Leave the bracket slightly loose until step 6. Photo 4 The best routing for the fuel line (Photo 5 & 6 ) requires drilling holes in the airbox. See Step 4 for hole locations. 4. Drill a 3/8″ hole at the front left corner of the airbox as shown in Photo 6. Make sure the location you choose will not result in the hole coming out behind the frame tube or into the rubber airbox boot. Be very careful drilling this hole.