Honda XR 400 Removal and Installation Manual

0

Filed Under (Honda) by admin on 09-12-2011

download
Turn Signal Switch Installation Front Wiring Connections Field Effect Transistor Installation Taillight Installation: Install the Acerbis DOT taillight over the empty well left in the stock fender using the two 5 x 20 mm bolts and 6 x 16 mm bolt found in the parts bag. Position the taillight over the previous taillight mounting well and transfer the hole locations for the top mounting holes onto the fender with a felt pen or snap punch (Photo 3) so that they are 3/8 of an inch above the edge of the taillight opening as shown in Photo 3. Drill two 3/16 inch holes for the top mounts. Attach the taillight using the top mounting screws, then pull the license plate holder down toward the bottom of the fender so that the taillight is pulled as horizontal as possible. Transfer drill a 1/4” hole at the bottom mounting location with the taillight in this position. When installing the bottom license plate mount bolt, make sure to install the 6 x 16 mm bolt from the bottom up to minimize the opportunity for the tire to grab it. Run the taillight
wires along the left frame rail using the stock wire clamps to support it. 8. Rear Turn Signal Installation: Turn signal mounting requires that you drill a 3/8 inch hole in either side of the rear fender near where it meets the side panels. You can achieve a clean,
durable installation using this mounting location. Mount the rear turn signals by drilling a 3/8 hole in the rear fender in the location shown in Photo 5, 3-3/4 inches back from the front edge (pointed tip of fender where it meets the side panel) and 2-3/4 “ up from the bottom edge Brake Light Switch Installation

Incoming search terms:

MOTORCYCLE SERVICE LIFT ADAPTER KIT FOR DYNA TC88 MODELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 28-04-2011

download
Installation A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. 1. See Figure 1. Position the motorcycle on a straight and level surface. While the bike rests on the Jiffy Stand, straighten the front wheel and place the frame leveling extrusion under the front tire to keep the tire straight. 2. Slide the motorcycle lift (fully lowered) under the bike from the right side (opposite jiffy stand side) lining up the frame rails with each of the perpendicular jacking rails on the lift. When properly aligned, the left frame rail will be approximately 1″ from the lift end section (Figure 2) and lift base will be adjacent to the Jiffy Stand (Figure 3). This will allow bike to be centered when moved to an upright position

HARLEY DAVIDSON CHROME DUAL GAUGE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
Installation To protect against shock and accidental start-up of vehicle, disconnect the negative battery cable before proceeding. Inadequate safety precautions could result in death or serious injury. Always disconnect the negative battery cable first. If the positive battery cable should contact ground with the negative cable installed, the resulting sparks may cause a battery explosion which could result in death or serious personal injury. Removal DISCONNECT ELECTRONIC SPEEDOMETER AND TACHOMETER 1. Refer to applicable Service Manual procedure and remove seat. 2. Refer to XLH Service Manual procedure and remove fuel tank. On FXD models, remove fuel tank mounting bolts and lift tank. 3. See Figures 1 and 2. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Detach sensor harness from left frame tube. 1 WARNING 1 WARNING 1 WARNING 4. Detach headlamp assembly from top fork bracket, to allow removal of speedometer sensor harness. 5. Unscrew speedometer reset switch boot. Remove cover screws and covers from backs of gauges. NOTE Some early electronic speedometers and tachometers were wired directly into the gauge

HARLEY DAVIDSON FXDWG ENGINE GUARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
FXDWG ENGINE GUARD KIT General This kit is designed for installation on 1993 and later FXDWG Dyna Wide Glide. QTY DESCRIPTION 1 Engine guard 2 U-Bolt 4 Locknut 1 Bolt, 3/8-16 x 7/8 in. 1 Lockwasher, 3/8 in. 1 WARNING This engine guard may provide limited leg and cosmetic vehicle protection under unique circumstances (fall over while stopped, very low speed slide). However, it is neither designed nor intended to provide protection from bodily injury in a collision with a vehicle or any other object. Installation 1. Lift engine guard into place. Align top center mount of guard with frame crosspiece member between frame downtubes. 2. Secure top center mount to frame crosspiece member using 3/8-16 x 7/8 in. bolt and lockwasher included in kit. Do not fully tighten at this time. 3. On right side of motorcycle, install U-bolt from kit around the frame member and into the holes in the lower mounting bracket. Secure loosely into place using two locknuts from kit. 1 CAUTION Left U-bolt must be installed between the frame and the clutch cable. Do not pinch clutch cable between the U- bolt and the frame. 4. On left side of motorcycle, install remaining U-bolt from kit around the left frame member and into holes in lower mounting bracket. Secure loosely into place using two locknuts from kit. 5. Tighten upper mounting bolt installed in step 2, to 30-33 ft-lbs. Alternately tighten U-bolt hardware to 25 ft-lbs. Tighten left and right side U-bolts evenly, so that approximately the same length of bolt protrudes from end of nut

HARLEY DAVIDSON DETACHABLE TOUR-PAK KIT FOR ELECTRA GLIDE CLASSIC INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Install Docking Kits and License Plate Holder 1. Install Rear Detachable Docking kit. Refer to the instruction sheet provided with kit. 2. Install Touring Detachable Tour-Pak Rack. Refer to the instruction sheet provided with kit. 1 4 2 3 is03989 1. License Plate Holder 2. Red Reflector 3. Original Equipment Screws 4. Original Equipment Bottom Support Tube Figure 2. Install License Plate Holder 3. See Figure 2. Install the new license plate holder (1) to the bottom support tube (4) using screws (3) saved from prior step. 4. Remove adhesive backing from red reflector (2) and carefully center and align it with the bottom edge of the license plate holder (1) and press firmly into place. -J03930 1 of 4 MOUNTING ANTENNA RELOCATION BRACKET 1. See Figure 6. Assemble joint assembly (9) to antenna mounting bracket (6) using lock washer (5) and 2 hex nuts (4). Tighten hardware securely. 2 1 5 4 3 is03992 1. Rear Docking Point 2. Docking Point Support Bracket 3. Antenna Mounting Bracket 4. Antenna/Cable Adapter 5. Rear Docking Point Screw and Locknut Figure 3. Relocated Antenna Bracket and Cable 2. See Figure 3. Install assembled antenna bracket (3) by removing screw and locknut (5) securing left rear docking point (1) to docking support (2). Install bracket as shown and reinstall rear docking point screw and locknut. Tighten screw and locknut to 15-19 ft-lbs (20.3-25.7 Nm) . 3. Thread antenna/cable adapter (4) onto joint assembly. ROUTING ANTENNA CABLES 1. See Figure 4. Gently remove left side cover (1) by pulling from frame tubes (no tools required). 2. Connect original antenna cable (not shown) to bottom of joint assembly. 3. Route antenna cable/wiring between left frame rail and fender. 4. See Figure 5. Attach cable to docking point support bracket in location (1) using short cable strap. 5. See Figure 4. Coil excess antenna cable/wiring (2) and use long cable strap (3) to fasten cable to frame under left side cover (1) with vehicle wiring harness. 6. See Figure 6. Cap unused wiring connector with connector housing (10).

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).

Incoming search terms:

HONDA VTX1300 AIR HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the rider and passenger seats, left chrome side cover & original horn located at the top of the radiator. 2. Locate the supplied black horn mounting bracket and supplied smaller hose clamp. Notice the slight twist in the bracket. Using 2 adjustable wrenches or a vise and one wrench remove the twist from the bracket. Route the hose clamp thru the bracket. (As shown in photo 1A) 3. Install the bracket on to the left frame tube, (As shown in photo 1A) and tighten securely. Bolt the supplied horns to the bracket using the supplied bolt, lock washer and nut, (As shown in photo 1) and tighten securely. Install the supplied trumpet covers (As shown in photo 1B) by flexing the spring clips over the trumpets. Check that they fit securely. If not remove covers, make sure the center screw is tight and bend spring clips in towards center of covers and re-install. Using a blade screwdriver pry the two supplied hoses with the “Y” connector off of the air horns cut a new piece of hose 3 ½” long from the hose and replace the short hose on the “Y”. Re-install the “Y” hose assembly with the short hose going on the long or upper trumpet. (See photo 1C) Re-route the original horn wires. (As shown in photo 1D) 4. From the supplied wire cut 2 pieces 28″ long. Strip ¼” of insulation from both ends. Crimp 2 supplied male terminals to one end and 2 supplied female spade terminals to the other end. Plug the male ends into the original horns wires. (As shown in 1D) Attach the remaining air hose to the “Y”. Tape the hose and wires together every 6-8″ using electrical tape to make routing easier and neater. Route the wires and hose up under the fuel tank, over the cylinder heads coming out between the frame rails at the rear of the fuel tank. (See photo 2A) Locate the supplied relay and plug the 2 wires from the original horn onto terminals 85 & 86 on the relay. (See wiring diagram on back of last page of instructions) This will be the 2 outer terminals that are parallel to each other. Locate the supplied fuse, holder & wire assembly. Crimp a supplied fork terminal to one end and a supplied female spade to the other. Attach the spade terminal to one of the remaining outer relay terminals. (#30 or 87 on wiring diagram) Remove the 3 Phillips screws from the battery top cover. Remove the cover and attach the fork end of the fuse wire to the positive (+) terminal. Re-install the battery cover. 5. Cut a wire 9″ long and strip ¼” insulation from each end, crimp a fork to one end and a female spade to the other. Attach this wire to the compressors negative (-) terminal. Cut another wire 18″ long and strip both ends. Crimp a female spade to both ends. Attach this wire to the compressor positive (+) terminal. Route the air hose out under the left side cover as shown in photo (3). Hold the compressor in place against the frame tube. Note: Looking at the large end of the compressor the space between the hose fitting and the bolt mounting flange forms a “V” shape. This is where the compressor should rest against the frame. Next loop the hose around to the compressor hose fitting and trim the hose to the desired length. Attach the hose to the compressor. Secure the compressor to the frame using 2 large supplied cable ties as shown. 6. (See photo 3A) Attach the compressor negative (-) wire to the bolt on the frame (As shown in photo 3B) Route the compressor positive (+) wire along the side up to the relay and attach to the remaining outer terminal 87 or 30. Cable tie the relay in place. (As shown in photo 2B) Use several of the supplied short cable ties to secure the compressor wires to the air hose (As shown in photo 3) as wells as any other loose wire or hose.

Incoming search terms:

HONDA VTX 1800 AIR HORNS AHVTX INSTALATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-12-2010

download
1. Remove the right and left frame side covers and the seat. 2. Unplug and remove the stock horn located behind the left foot peg. Re-route the horn wires up over the front cylinder head and to the rear. Next cut two pieces of wire 36″ long, strip both ends ¼”, crimp two male spade terminals to one end and two females to the other ends. Attach these wires to the stock horn wires and route them over the rear cylinder and behind the frame tube. The end of the wires should come out near the center of the left side cover area (see photo 1 A). Connect these two wires to the relay terminals 85 & 86 (these will be the two that are parallel to each other see wiring diagram for terminal identification). 3. Using a blade screwdriver pry the two hoses with the “Y” connector off of the air horns. Cut a new piece of hose 2 ¾” long, replace the old short hose on the “Y” with this. Re-install the “Y” hose assembly onto the horns with the short hose on the long trumpet, route the hoses behind the horns and connect the long hose to the short horn (see photo 2A). 4. Remove the upper 8mm (12mm wrench size) motor mount bolt (see photo 2B). Install the horn assembly using the 8 x 55mm bolt and spacer tube provided. If the motorcycle is fitted with Honda line tubular radiator or engine guards the above mounting will not work. You will need instead to locate the “J” shaped bracket and small hose clamp provided in the hardware kit (see photo 2 on instructions of multi -application instruction sheet). Thread the hose clamp thru the bracket and attach to the frame or Honda line guards as shown ( see photos 2&3 ) tighten the hose clamp securely using a socket or wrench. Attach the horn set to the “J” bracket using the 5/16 x ¾” bolt, nut and lock washer provided. Position the horns so that they are angled down just slightly then tighten the bolt securely. Attach the remaining air hose to the “Y” connector, route the hose up over the top and to the rear of the engine. Cross the hose over to the right side of the rear cylinder head, then behind the electricals of the right side cover and coming out as shown ( see photo 3 A & B ). 5. Remove the center relay from its mounting bracket by lifting it upward and re-attach it lower and at an angle as shown (see photo 3C) using a small cable tie. Route two long cable ties thru the hole in the relay mounting bracket as shown (see photo 3D). Next cut a 16″ wire, strip both ends, crimp female spades to both ends. Attach this wire to the compressors pos (+) terminal. Cut an 8″ wire, strip both ends, crimp a female spade to one end and a fork terminal to the other. Attach this wire to the compressors neg. (-) terminal. Cable tie the compressor securely in place as shown (see photo 4). Route the hose to the compressor making sure there are no tight bends or kinks cut the hose to the desired length and attach it to the compressor. Route the neg. (-) wire with the fork terminal up and attach it to the 10 mm bolt as shown (see photo 4A) . Route the pos. (+) wire over to the relay on the left side of the motorcycle and attach it to terminal 30 or 87 on the relay (see wiring diagram)

Incoming search terms:

Yamaha Road Star Engine Guard Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1. Protect the rear portion of the front fender with a towel or other thick, soft cloth. 2. Remove the OEM engine guards if they have been installed on the motorcycle. Or, if OEM engine guards are not present, Remove the two lower engine mount bolts. These bolts are located on the inside of the right and left frame rails, and will be replaced with the longer 10mm bolts included with your new engine guard. 3. Position the engine guard so that the lower brackets point towards the rear of the motorcycle, and slide the engine guard into the space between the front wheel and the frame. 4. Raise the guard until the upper V” mount is located between the frame rails. Note: Your new Barons engine guard is equipped with a unique upper V” mount clamp. This clamp becomes a cradle for the upper frame supports when it is inserted between the frame rails. 5. Rotate the engine guard until the lower mounting brackets are aligned with the lower engine mount holes. Due to production line tolerances in both the motorcycle and the engine guard, the mounting brackets may be too wide or too narrow for the frame. If this is the case, remove the guard from the motorcycle. Place the guard on a flat, firm surface. Insert a towel or other protective material between the guard and the surface. Using a rubber mallet or a block of wood and a hammer, tap the lower brackets until they are correctly spaced. 6. Insert the new 10mm bolts and washers, and finger tighten only. 7. Tighten each 3/8″ bolt in the upper clamp evenly by using a 9/16″ socket or a wrench. Snug down each bolt until it draws the front of the upper clamp into contact with the upper frame supports, then adjust these bolts accordingly to achieve equal spacing between each floorboard and the lower engine guard rail. 8. Tighten the jam nuts against the washers to lock each bolt in place. CAUTION! It is critical that you do not over-tighten these bolts. Tighten all remaining nuts and bolts securely. If necessary, slightly loosen rear brake line banjo bolt and rotate banjo fitting for clearance with engine guard. Tighten banjo bolt and check brake for proper operation. You must re-tighten all four of the engine guard mounting bolts after 100 miles of riding! Care & Cleaning: Engine guards take the full brunt of the worst of what the weather in your area has to offer, making it critical that proper and complete cleaning take place on a weekly basis, or corrosion will occur which is not covered by warranty! Proper cleaning procedure would be to use a product like Simple Green, LOC, Salt-Away or similar. Mix a strong batch and apply it liberally with a soft towel or soft nylon brush to the entire

Incoming search terms:

2009 VULCAN 1700 HEAT SHIELD KITS INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Installation Procedure Refer to the appropriate sections of the Service Manual for information and procedures related to parts removal and installation. NOTE: Cover the frame with tape on the left and right o sides (right side shown, left side similar) to prevent scratches during shield installation Remove and discard upper left and upper • right radiator screen mount screws (right side shown, left side similar). Install the heat shield along the upper edge • of the radiator and attach the shield and the screen with the radiator screen mount screws provided in the kit Remove the tape from the frame rails. • Install the clutch hose in the clamp on the left • frame tube. Front Cylinder Exhaust Cover NOTE: Apply penetrating oil to the exhaust cover o clamp screws prior to loosening. Loosen the exhaust pipe cover clamp screws. • Remove and discard the exhaust cover. •

Incoming search terms: