2004-2005 Harley Davidson Dyna EFI Tuner Installation Manual

0

Filed Under (Harley Davidson) by admin on 14-04-2012

download
1 Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through the box and into the small opening in the frame (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Data plug Remove bolt Remove bolts FM810 www. fuelmotousa.com 2004-2005 Harley Davidson Dyna – FM EFI Tuner – 2 8 Plug the black connector of the Power Commander into the stock wiring harness connector (Fig. D). 9 Route the grey connector of the Power Commander through the box and plug it into the ECM. 10 Install the Power Commander against the rear part of the electrical box. Make sure to clean both surfaces with the alcohol swab first. Use the supplied velcro to attach the Power Commander. 11 Bolt the box back into place. 12 Reinstall the seat. Fig. D Fig.

Incoming search terms:

2003-2004 Harley-Davidson V-Rod Power Commander Installation Instructions

0

Filed Under (Harley Davidson) by admin on 05-04-2012

download
1 Remove the seat, air box shell, and airbox cover. 2 Remove the left hand side cover by removing the 5mm allen bolt (Fig. A). Fig. A Fig. B Fig. C Remove this bolt Unplug the stock connector from the ECM Route harness from PCIII under frame rail PC connectors
5 Route the PCIII harness behind the stock wires (Fig. D). 6 Plug the connectors from the PCIII in line of the stock wiring harness and ECM (Fig E). 7 Tuck the two connectors in the lower right corner of the frame (Fig. F)

2007-2010 Harley Davidson Dyna EFI Tuner INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2012

download
Remove the seat 2 Remove the left hand side cover (Fig. A). 3 Unplug the stock wiring harness connector from the ECM (Fig. B). 4 Move the data plug (Fig. B) out of the way to access bolt. 5 Remove the 3 bolts that hold the electrical box in place (Fig. B). 6 Slide the plastic box out from the frame. 7 Route the stock connector through to the back side of the electrical box (Fig. C). Fig. A Fig. B Fig. C Remove side cover Stock connector Stock connector Dat a plug Remove bolt Remove bolt s FM814 www .fuelmotousa .com 2007-20 1 0 Harley Davidson Dyna – FM EFI Tuner – 2 8 Lay the PCIII behind the electrical box temporarily. 9 Route the GREYconnector from the PCIII through the back of the electrical box and plug it into the ECM (Fig. D). 10 Connect the stock wiring harness to the BLACK connector of the PCIII. 11 Zip tie these connectors to the front side of the electrical box (Fig E). Make sure they are situated away from the rear exhaust pipe. Fig. D Fig. E PCIII connector Stock connector PCIII connector 12 Mount the PCIII to the underside of the stock ECM (Fig. F) using the supplied velcro. Make sure to clean both surfaces with the alcohol swab before attaching. Situate the PCIII so the USB and expansion ports point to the rear of the bike. This will allow you easier access to adjust the maps if necessary

Incoming search terms:

2010 Harley Davidson Touring Model Power Commander Installation manual

0

Filed Under (Harley Davidson) by admin on 29-02-2012

download
1 Remove the stock seat. 2 Unplug the stock wiring harness from the ECM (Fig. A) . 3 Plug the PCV connectors in-line of the stock ECM and wiring harness (Fig.B). 4 Tuck the PCV to wiring harness connection into the opening in front of the battery box (Fig. C). 5 Using the supplied velcro attach the PCV to the top of the ECM (Fig. C) FIG.A FIG.C Remove Ground wire FIG.B PCV connector PCV connector Stk connector Connection 15-011 www.powercommander.com 2010 Harley Davidson Touring PCV – 4 6 Remove the right hand saddlebag and sidecover. 7 Locate the stock O2 sensor connections and unplug both connectors (Fig. D) The stock O2 sensors will NOT be connected to anything at this time. The sensors can be removed from the exhaust if you have a way to plug the hole. Unplugging the sensors does NOT cause an engine light but will cause a historic code in the ECM for non-active O2 sensor. This is not causing any issues with the running of the bike. FIG.D Follow these instructions when using the Auto tune kit – part #AT-100B 1 Remove the left hand side cover. 2 Place the Autotune modules in front of the battery as shown in Figure H. If using velcro make sure the velcro does not cover the designation of the unit on the back (AT #1 or AT#2). The modules are coded to the front and rear cylinders. FIG.E 3 Remove the rubber plug for the diagnostic connector. Plug the lead from the Autotune kit into the stock diagnostic connector (Fig. J).This connection is under the LH sidecover. DO NOT connect to the accessory connection in front of the battery. 4 Reinstall the sidecover. FIG.F 15-011 www.powercommander.com 2010 Harley Davidson Touring PCV – 5 5 Connect the longer harness to the front O2 sensor. Route the harness along the front down tube and along the backbone of the frame to Autotune module AT#1. Wire the harness to the module per Figure G. The harness can be cut to length if desired. 6 Repeat step 4 for the rear cylinder. Wire the harness to Autotune Module AT#2. The harness can be cut to length if desired. If your exhaust does not accept the M18x1.5mm O2 sensor you will need to install the supplied O2 bungs with the Auto tune kit into your exhaust. See Auto tune instructions for more information

KTM Superduke 990 MotoHooligan Airbox Installation

0

Filed Under (KTM) by admin on 26-01-2012

download
Undo the screws retaining the left and right front tank spoilers and remove. Fitment of Motohooligan airbox is possible without removing the tank but task is much easier if this is done. Access for removal of SAS system and installation of PC111 is also much improved and it’s worth the additional 5 minutes work. It would also be a good idea to do this with an empty tank so it’s lighter to handle. Unscrew front retaining bolt from front of tank and lift tank to access the spring damper on the left hand side. On standard Superdukes release the two circlips, carefully support tank and remove damper unit. (NB. SDR model not fitted with damper). Lower tank back into position and unscrew one of the pivot bolts at rear of tank Stage 1 – remove spoilers and tank Note : Fuel line has a connector half way between tank and airbox. but leave it in position to support the tank whilst you unscrew the other side. Once both bolts are unscrewed tank is free but still attached by fuel lines and electrics. Lift the rear of the tank to expose the two electrical plugs and disconnect both making sure that the retaining pins are pushed in first before you pull them apart. Reaching underneath the rear of the tank you’ll see the fuel line running into the base of the airbox. Half way down there is a connector with a metal button. Press this and pull the fuel line apart – you might want to have a rag handy to catch any fuel drips. Pull off the breather tube at the front, (on US models also pull off the breather that leads to the charcoal canister in the tail), and lift the tank away

Incoming search terms:

2002-2003 Yamaha YZF1000 R1 STARTING INSTALLATION

0

Filed Under (Yamaha) by admin on 13-01-2012

download
Remove the main seat and the passenger seat / solo cover. 2 Lift the front of the fuel tank up. 3 Locate the connectors shown in Fig. A. These connectors are located behind the throttle bodies on the left hand side of the bike. 4 Unplug the two connectors shown in Fig. A. Fig.A PLEASE READ ALL THE DIRECTIONS BEFORE STARTING INSTALLATION Unplug these connectors I405-211 6 3 Fig.B 5 Plug the fuel connectors from the PCIII (clear connectors) in-line of the stock wiring harness (Fig. B). Stock connectors PCIII connectors 6 Plug the TPS connectors from the PCIII (white connectors) in-line of the stock wiring harness (Fig. C). Fig.C Stock connectors PCIII connectors I405-211 Trouble Shooting If you feel that you are having any problems at all with the Power Commander III, disconnect it from your motorcycle. This will allow the motorcycle to run directly off of the stock ECU. The lights don’t come on when I turn the ignition switch on. Check to make sure connectors are seated and the kill switch is in the “run” position

Incoming search terms:

2007 Honda CBR600RR Power Commander Installation Instructions

0

Filed Under (Honda) by admin on 16-11-2011

download
Remove the bolt that holds the ground wires and bracket for the alternator connectors to the frame on the left hand side of the bike. This allows access to the Throttle Position Sensor connector. Unplug the stock wiring harness from the Throttle Position Sensor (Fig. F).Remove the main seat and the passenger seat. Remove the fuel tank cover. Remove the left hand fairing. Prop the fuel tank up. Lay the PCIII in the tail section temporarily and route the harness underneath the tail sec- tion (Fig. A). Removing the 4 bolts that hold the tail sectionb in place will make this easier Route the harness towards the throttle bodies (Fig. B) Attach the ground wire from the PCIII to the negative side of the battery.

HARLEY DAVIDSON MOUNTING BRACKET SERVICE MANUAL

0

Filed Under (Harley Davidson) by admin on 12-04-2011

download
INSTALLATION 1. See Figure 1. Note position of mounting brackets (1). Remove old mounting brackets and discard. NOTE On 1997-2000 models, the air fittings are installed to the two mounting holes on the right-hand right side bracket. On 2003 and later models, the single air fitting is installed to mounting hole on the left-hand side bracket. 2. See Figure 2. Install new mounting brackets from kit on each side of the motorcycle using new locknuts as follows: a. Use the 5/16-18 x 1 inch screws (5) in the upper two holes with 2 chrome washers (3) placed between the mounting bracket and the saddlebag support at each of the two locations. Install a 5/16-18 flange locknut (2) behind the screw that does not screw into a weld nut. Tighten to 15-19 ft-lbs (20-26 Nm). b. On each side, install a 1/4-20 x 7/8 inch screw (9) through the bottom hole of the mounting bracket and the saddlebag bracket as shown, with a chrome washer (3) placed between the mounting bracket and the saddlebag bracket. Tighten to 10-14 ft-lbs (13.5- 19.0 Nm). On 1997-2002 models, install the air line fittings to the lowest two holes drilled in the right side bracket. On 2003 and later models, install the single air line fitting to the lower front hole drilled on the left side bracket. c. See Figure 2. On each side, attach docking points (6) in their proper location on mounting bracket with 3/8- 16 x 1-1/2 in. buttonhead screws (7), washers (3) and locknuts (8) but leave locknuts slightly loose so docking points can be adjusted for proper fit. On 1997and later models, the docking point will attach through the front hole of the mounting bracket as shown. On 1994-1996 models, the docking point will attach through the rear hole of the mounting bracket. d. Place detachable passenger backrest into docking points as described in the Backrest Instruction Sheet. Make sure that the forward notches of the sideplates are pushed completely into the forward docking points, then tighten the rear docking points securely to 45-47 ft/lbs (61.0-64.0 Nm

Incoming search terms:

HARLEY DAVIDSON DYNA DOCKING HARDWARE FOR FXDX WITH WIDE TIRE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
Installation NOTE Perform the following procedures on one side of the motorcycle until instructed to go to the other side. To keep fender in alignment the front docking point will be mounted first. INSTALLING DOCKING POINTS NOTE Save the acorn nuts and washers removed from the fender support bracket for use when installating docking points. 1. Loosen and remove the acorn nuts, washers, and screws from the fender support (right-hand) bracket. Save the washers and acorn nuts for docking point installation. Discard screws. 2. Obtain 1 plastic bushing, labeled 01, from a bushing set. 3. Place the bushing (4) (beveled side out) into the front support hole as shown in Service Parts illustration. 4. Place the countersunk side of the front docking point (2) so that it engages bushing (4). 5. From underneath (inside) the fender, insert hex-head screw (1) through fender, support bracket and front docking point (2). 6. Install washer (7) split lockwasher (5) and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 7. Obtain another plastic bushing, labeled 01 , from the bushing set. 8. Place bushing (4) (beveled side out) into the the rear support hole as shown in Service Parts illustration. 9. Place the countersunk side of the rear docking point (3) so that it engages bushing (4). 10. From underneath (inside) the fender, insert hex-head screw through fender, support bracket and rear docking point (3). 11. Install washer (7) split lockwasher (5)and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 12. Repeat procedures 1 through 11 for opposite (left-hand) side of the motorcycle. NOTE In time docking points may wear, causing the sideplates to become loose. The fit may be tightened using the following procedure. 1. Loosen docking hardware. 2. Rotate docking points clockwise approximately 45°. 3. Tighten docking hardware to the appropriate torque values. Repeat as often as required, up to 3 times

Incoming search terms:

HARLEY DAVIDSON V-ROD CHROME UPPER SIDE COVERS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
INSTALLATION 1. See Figure 1. Remove and discard screw (1) at upper side corner of side cover (2). 1 2 3 is01410 1. Screw 2. Side cover 3. Frame Figure 1. Existing Side Cover Removal (right side shown) 2. Lift up slightly to remove side cover from frame (3). Discard side cover. 3. Repeat for left hand side cover. 4. See Figure 2 and Table 1. Place rubber mounts (1) (installed on covers) over tabs in frame and use screws (2) from kit to fasten side covers (3) and (4). 5. Tighten side cover screws to 11-17 Nm (98-150 in-lbs ). 2 4 3 1 1 is01411 Figure 2. V-Rod Chrome Upper Side Covers Table 1. V-Rod Chrome Upper Side Covers Part Number Description (Quantity) Item 11524 Rubber mount (4) 1 Not Sold Separately Screw (2) 2 Not Sold Separately Side cover, right (chrome) 3 Not Sold Separately Side cover, left (chrome

Incoming search terms:

Incoming search terms: