TRIUMPH ROCKET III HEEL / TOE SHIFTER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Loosen the 10mm nuts at the ends of the shifter linkage rod (notice one end is a left hand thread). Remove the 10mm nut from the shifter arm & disengage the linkage. Remove the shifter pivot bolt using a 8mm hex key wrench. Remove the washer on the threaded side of the shifter pivot bolt. 2. Place one of the wave washers supplied onto the pivot bolt. Place a small amount of grease on the shifter pivot bolt shank and the Heel / Toe shifter pivot hole, insert the pivot bolt into the pivot hole of the toe heel shifter. Use a drop of blue loctite on the shifter pivot bolt threads and install the Heel / Toe shifter, tighten the pivot bolt securely. Check to see that the shifter pivots freely. If the side play is excessive (this is a result of variances in manufacturing tolerances of the stock and supplied components) remove the pivot bolt and install the second wave washer supplied. 3. Unscrew the linkage rod and replace it with the longer rod supplied (NOTE the rod has a left hand thread on one end and right hand threads on the other). Insert the shifter linkage stud into the desired hole in the new shifter being sure the flats on the stud engage the slot on the backside of the bolthole. Install the nut and finger-tighten only at this time. 4. While seated on the motorcycle first find the height setting you prefer for the toe shifter. Using one of the three boltholes for the linkage can set this. You can also gain some adjustment by exposing more or less threads of the new longer shifter linkage rod; however be sue that you have a minimum of 4-5 threads still engaged in the linkage ends. After setting the height, tighten all three 10mm nuts (the two at the ends of the linkage rod and the one which attaches the linkage to the toe/heel shifter) securely. After you have the toe shifter adjusted to your liking you can select the heel shifter height by moving the button head cap screw that secures the toe shifter to the heel shifter (Using a 5/32″ hex key wrench) next to the 10mm linkage nut to any of its three holes

Incoming search terms:

Daytona 675, Street Triple Street Triple R Fitting Instruction

0

Filed Under (Triumph) by admin on 29-10-2010

download
remove the original gear selector rod from the motorcycle. Note: The ball joint and locknut on the transmission linkage have a left hand thread. This is identified by either a machined ring on the gear selector rod on Daytona 675 or on the ball joint on Street Triple and Street Triple R. 1. Front ball joint 2. Locknut 3. Gear selector rod 4. Machined ring, left hand thread identification 5. Machined ring, left hand thread identification (StreetTriple and Street Triple R) 6. Remove the front and rear ball joints and front locknut only from the gear selector rod. Retain the locknut and both ball joints for re-use. Retain the gear selector rod if the motorcycle is to be returned to its original condition. 7. Remove the plastic end caps from the quickshifter assembly. 8. Screw the locknut on to the rear of the quickshifter assembly (right hand thread) leaving 8mm of thread exposed. 1. Quick shifter assembly 2. Locknut 9. Screw the rear ball joint (right hand thread) on to the rear of the quickshifter assembly until it contacts the locknut. Unscrew the ball joint, only enough to achieve the correct orientation in relation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 10. Fit the locknut and front ball joint (left hand thread) to the front of the quickshifter assembly Screw the locknut and ball joint on to the quickshifter assembly to achieve a dimension between the ball joint ends of 203.5 mm. Ensure that the ball joint is in the correct orientation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 12. Route the quickshifter cable through the gear selector rod aperture in the frame, as shown. 1. Quickshifter cable 2. Gear selector rod aperture 13. Locate the quickshifter assembly in position, through the frame with the sensor at the rear and the cable at the top. 1. Quick shifter assembly 2. Sensor 14. Attach the front ball joint to the transmission linkage. 1. Ball joint 2. Transmission linkage

Incoming search terms:

KAWASAKI TERYX 750 CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove both seats from the vehicle. Next, remove the passenger side lower body panel. There is a mixture of Philips head screws and also plastic push pin fasteners that have to be removed. 2. With the side panel off, the next item to remove is the plastic housing over the engine. These are all “push in” style plastic clips that hold it in place. Once all the pins are out, you can slide the housing off and set it aside. 3. Now the lower long plastic panel under the seat has to be removed (again mainly plastic push clips to remove) . Once they are all out, carefully remove and set aside. 4. Next, remove the fuel tank. Remove the two lines on the top of the tank. There are two straps that hold the tank in place. Remove the bolt from each strap, remove the straps, and lift the fuel tank out. 5. Now the bracket that holds the fuel pump on has to be removed. There are two bolts here to take out. Once this is done, mark the two wires to the coil and disconnect them. Set the bracket out of the way . 6. Next, the clutch cover bolts can be removed and the norkel on the housing can be loosened and i Teryx 750 Clutch Kit Instructions 5/1/09 removed. Take the clutch cove off and set out of the way. 7. With the clutch visible, you can remove the secondary clutch with a large impact wrench and metric socket . 8. Remove the bolt from the primary clutch. This is a left hand thread on the bolt. Next you will need a Kawasaki drive clutch puller (part #352251) to pop the clutch loose. If you do not have a puller, the spring cap can be removed on the vehicle and the weights can be changed out in there as well. 9. With the clutches sitting on the bench, remove the bolts that hold on the spring cover. Remove the stock spring and the stock weights 10. After reading the directions on the new weights, add the correct amount of weight to each clutch weight and install them in the clutch. Place the weight to the left side in the clutch pocket and then install the aluminum spacer. Repeat this process for the other three weights. 11. Install the new spring supplied in the kit and install the spring cover, paying close attention to the arrows on the cover. 12. Next, remove the stock spring from the secondary. It is recommended that you use the TEAM Compression tool (part # 930001) for this. With the clutch on the compression tool, compress the spring retainer down far enough to remove the snap ring with the needle-nose pliers . Slowly back off the t-handle and remove the tool.

Incoming search terms: