Yamaha WR 250F and WR450F Dual Sport Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-01-2012

download
license Plate Mount Installation: Locate the aluminum license plate mount and license plate light assembly. Remove the rear most nut securing the stock taillight assembly (underneath the fender) (don’t lose the little compression tube and washer). Temporarily install the license plate mount to this location and mark the fender where it needs to be drilled for the rear mounts. Drill the fender in two places with a ¼” drill and reinstall the license plate assembly using the stock taillight mount and the 6 x 20 mm countersunk screws, bezels and nylock nuts Rear Turn Signal Installation: Locate the two rear turn signals in the kit – they’re the ones with the longer wires. Drill a 3/8 hole in each side of the fender as shown in Photo 3 and attach them as shown in Photo 4. It does no matter which signal goes on which side. Run the left turn signal wires forward along with the taillight wires, up through the grommet in the fender to the area just behind the air box cross member and above the fender. Run the right turn signal wires forward along the right frame rail, and through the same hole you made for the license plate wires Brake Light Switch Installation: The WR250/450 uses a hydraulic brake switch. This requires replacing the rear master cylinder banjo bolt with a specially made switch. Installing the switch requires bleeding the rear brake. If you do not feel competent bleeding your rear brake, please refer this job to a qualified mechanic, as failure to do it correctly will make the brake inoperable. Remove the rear master cylinder guard. Remove the bolt holding the brake fluid reservoir to provide access to the master cylinder. Loosen the banjo bolt securing the rear brake line to the master cylinder. Typically, this bolt will be very tight and loosening it will bend the support hanger for the master cylinder if not supported. Brace the master cylinder with a wrench or lever. Remove the banjo bolt and replace with the hydraulic switch. Make sure to install the copper crush washer from the stock bolt under the switch. Torque the switch assembly to 25 lb-ft.

HONDA GL1100 AM/FM RADIO INSTALLATION MANUAL/ WIRING DIAGRAM

0

Filed Under (Honda) by admin on 22-04-2011

download
INSTALLATION ■ Outline Procedures This section gives general information needed for mounting the individual radio components on and in the fairing. A) Fairing 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove fairing parts. 3) Drill unit mount holes. 4) Install six wire clips. 5) Install windshield on fairing before install- ing speakers. 6) Install radio indicator I on indicator panel II , then install indicator panel on fairing. 7) Install speakers III. 8) Install nutplate IV. 9) Install Power Amplifier in fairing. 10) Install radio funer VI. 11) Install the radio controller VII. 12) Install controller base panel VIII 13) Install radio switch sub-wire. 14) Connect adapter harness and wires inside fairing by working through left turn signal lens hole. B) Motorcycle frame and handlebar 1) Remove travel trunk and seat. Unscrew four shelter bolts (M6, one on each side at front and rear) to route antenna feeder. 2) Install antenna mount and antenna IX. 3) Route antenna feeder along the frame tube. 4) Install radio switch X on left handlebar lever bracket and route the wires. 3 of 11 Page 4 C) Fairing instllation 1) Install fairing on motorcycle. 2) Connect motorcycle wire harness 9-P coupler to fairing wire 9-P coupler. 3) Connect radio switch wire to switch sub- wire.4) Connect antenna feeder. 5) Confirm that radio operates properly. Reinstall parts removed in step 2 or (A) and in step 1 of (B). REWORKING ■ Remove Fairing and Fairing Parts (Fig.10) 1) Install radio on fairing before mounting fairing on motorcycle. (Remove fairing from your motorcycle when already mounted). 2) Remove right and left fairing pockets, right and left turn signal lenses, right and left nutplates, left hole cover and indi- cator base panel from fairing. (Fig.10) Fig. 10 LEI-1 NU I PLATE 4 of 11■ Reworking on Fairing — Speaker mounting holes- 1) Remove 18 mm grommet. 2) Lightly roll template so that it will follow contour of fairing snugly. 3) Position template on fairing with its upper and outer edges aligned with those offairing as indicated by arrows. 4) Attach template to fairing using adhesive tape where shown. 5) Punch mark centers of four holes with a
drift and hammer. 6) Drill 6 mm holes through marked centers. To obtain a more balanced response with richer, deeper bases, drill two 50 mm holes in the fairing so as to link the speaker box with the inside of the fairing. Fig. 11-1
—Power amplifier mounting holes- 7) Drill two 5.5 mm holes through concaves in fairing. Fig. 11-2 RIGHT HAND SHOWN, LEFT SIMILAR ADHESIVE TAPE

Incoming search terms:

HARLEY DAVIDSON V-ROD CHROME TURN SIGNALS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-02-2011

download
INSTALLATION Prepare the Motorcycle 1. Remove the right cover and the maxi-fuse. 2. Follow Service Manual instructions to remove the air box cover. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Follow Service Manual instructions given to remove the negative (-) battery cable from the negative (-) battery terminal. Remove the Existing Rear Turn Signals 1. See Figure 1. Insert a screwdriver into middle of hole of license plate light cover. Push forward to release tail lamp housing retaining clip. 2. See Figure 2. Identify the white left [19] (1) and black right [18] (2) 2 pin turn signal connectors. is 00231 Figure 1. Tail Lamp Housing 2 1 is00232 1. Left turn signal connector [19] (white) 2. Right turn signal connector [18] (black) Figure 2. Rear Turn Signal Connectors 3. See Figure 3. Press the button (1) and separate the pin terminal housing from the socket terminal housing. -J03601 1 4. On the socket terminal housing, press the latch (2) aside and open the secondary lock (3). 5. To release the socket terminal and wire, insert a pin (6) into the front socket cavity. Compress the tang (4) while gently pulling the wire and socket terminal (5) from the back. 6. See Figure 4. Inside the fender, remove the fasteners (1) and the turn signal support plate (2). Pull the turn signal wiring through holes in license plate mounting bracket (3) and remove turn signals. 7. Repeat for the opposite turn signal. Install Chrome Rear Turn Signals 1. See Figure 5. Assemble a chrome turn signal assembly (1) to a chrome lamp support (2) by feeding the wire leads through the wire hole in the lamp support. 2. Feed the wire leads and conduit through the front hole in the license plate bracket and through hole in the support plate (4) towards the front of the motorcycle. 3. Thread the bolt (3) through the center hole in the support plate, through the center hole in the license plate bracket, and through the hole in the chrome lamp support into the chrome turn signal. 4. Tighten the bolt to 100-150 in-lbs (11.3-16.9 Nm). 5. Route the turn signal wires between the license plate bracket and the inner fender. Access the wires through the tail lamp opening in the outer fender. 6. See Table 1. Identify the left and right connector socket housings and match the socket terminated colored leads to the cavities in the socket housing which correspond to the colored leads in the pin housing

HARLEY DAVIDSON LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 3 2 1 is00851 1. Tail/stop lamp connector 2. Left turn signal connector 3. Right turn signal connector Figure 1. Rear Lamp Connectors 1. Raise the vehicle on a motorcycle lift to allow access to the underside of the rear fender. 2. Refer to the Service Manual and follow the instructions given to remove the negative battery cable (earlier Dyna models) or Maxi® Fuse (all XL’s and later Dyna models). 3. Remove the license plate from the vehicle (if installed). Remove and discard the original equipment license-plate bracket and attaching hardware from the fender. Clean the mounting area on the fender with a soft, damp cloth. 4. See Figure 1. Remove the two screws securing the tail/stop lamp lens assembly, and remove the lens and bulb assembly. Depress the latch on the four-way tail/stop lamp connector (1), and disconnect the connector from the circuit board. 5. Depress the latches on the left-side (2) and right-side (3) two-way turn signal connectors, and disconnect the connectors from the circuit board. 6. Remove the turn signal wires from the retention clips under the fender.

HARLEY DAVIDSON 180 MM WIDE TIRE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION Install Wide Tire 1. Place motorcycle on a lift and secure front tire. 2. Place a scissor jack under the frame so that the rear wheel can be raised and lowered. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect battery negative (-) cable. 4. Refer to the appropriate Service Manual and remove the rear wheel. 1 3 4 2 is00773 1. Tail/Stop Connector 2. Left turn signal connector 3. Right turn signal connector 4. Power in connector Figure 1. Remove Connectors 7 8 9 1 6 2 4 5 3 is00705 1. Rear fender 2. Stock rear fender bracket 3. Stock washer 4. Stock hex screw 5. Stock washer 6. Rear fender bracket from kit 7. Stock fender strut cover 8. Stock screw 9. Stock turnsignal and mount assembly Figure 2. Replace rear fender bracket

TRAILER ELECTRICAL ISOLATOR Installation Procedures

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Control circuit connections to the motorcycle (normally under the seat or trunk): #1 Brownwireshould be connected to the taillight circuit. #2 Green/Redshouldbe connected to the brake light circuit. #3 LightBlueshould be connected to the left turn signal circuit. #4 Orangeshouldbe connected to the right turn signal circuit. #5 Greenwireshould be connected to frame ground (not to the battery negative post) #6 Yellowwire should be connected to positive 12 volt battery supply. TRAILER ELECTRICAL ISOLATOR WARRANTY -Krissproductsare covered under our standard limited warranty Items returned for inspection must have prior return authorization from the factory. All items must be sent freight prepaid. We are not responsible for any item returned without authorization. Technical assistance is available on the Internet. All items returned for inspection and found to operate properly will be subject to a minimum testing fee. Complete details of our limited warranty maybe found on our internetpages. for defective materials and workmanship. NOTE: Please observe standard good installation procedures by not placing or attaching electrical devices next to plastic decorative outer panels or fairings to prevent damage due to heat. Electricity can produce high temperatures in the event of short circuits. KRISS INDUSTRIESINC. wwwkriss.com . Techinical Support Warranty Assistance Product Information Contact Information KRISS MOTORCYCLE PRODUCTS Installation Procedures Use a test light to identify the correct circuits. If you do not have the proper tools or knowledge to identify the proper wiring we suggest that you seek professional assistance locally. Please note that we are notable to provide telephone or email installation and/or electrical training

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms:

YAMAHA XV1700 PCR/ XV1700 PCRC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 02-12-2010

download
High beam indicator light “” 2. Right turn signal indicator light “” 3. Fuel level warning light “” 4. Engine trouble warning light “” 5. Left turn signal indicator light “” 6. Neutral indicator light “” 1. Speedometer INSTRUMENT AND CONTROL FUNCTIONS 3-4 3 EAU04436 Tachometer unit The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range. The tachometer unit is equipped with the following: ● an odometer (which shows the total distance traveled) ● two tripmeters (which show the distance traveled since they were last set to zero) ● a fuel reserve tripmeter (which shows the distance traveled since the fuel level warning light came on) ● a meter lighting control ● a clock ● a self diagnosis device NOTE: ● Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons. ● To switch the odometer, the trip- meters and the fuel reserve trip- meter displays between kilometers and miles, press the “SELECT” button for at least two seconds. ECA00123 CAUTION: Do not operate the engine in the tachometer red zone. If operated in the red zone, the tachometer segments will start flashing to notify the rider. Red zone: 5,000 r/min and above 1. Tachometer 2. Clock 3. Odometer/tripmeter/fuel reserve tripmeter 4. “RESET” button 5. “SELECT” button 1. Tachometer red zone
INSTRUMENT AND CONTROL FUNCTIONS 3-5 3 Odometer and tripmeter modes Pushing the “SELECT” button switches the display between the odometer mode”ODO” and the tripmeter modes “TRIP 1″ and “TRIP 2″ in the following order: ODO→ TRIP 1 → TRIP 2 → ODO If the fuel level warning light comes on (see page 3-2), the odometer display will automatically change to the fuel reserve tripmeter mode “TRIP F” and start counting the distance traveled from that point. In that case, pushing the “SELECT” button switches the display between the various tripmeter and odometer modes in the following order: TRIP F → TRIP 1 → TRIP 2 → ODO → TRIP F To reset a tripmeter, select it by pushing the “SELECT” button, and then push the “RESET” button for at least one second. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to the prior mode after refueling and traveling 3mi (5km). Meter lighting control mode 1. Turn the key to “OFF”. 2. Push and hold the “SELECT” but- ton. 3. Turn the key to “ON”, and then after five seconds, release the “SELECT” button. 4. Push the “RESET” button to select the desired brightness. 5. Push the “SELECT” button to set the brightness level. 6. Turn the key to “OFF”. NOTE: When adjusting the meter lighting, the odometer display will indicate the brightness level. Clock mode To set the clock: 1. Push the “SELECT” button and “RESET” button together for at least two seconds. 2. When the hour digits start flashing, push the “RESET” button to set the hours. 3. Push the “SELECT” button, and the minute digits will start flashing. 4. Push the “RESET” button to set the minutes. 5. Push the “SELECT” button and then release it to start the clock. NOTE: ● After setting the clock, be sure to push the “SELECT” button before turning the key to “OFF”, otherwise the clock will not be set. ● To set the clock after the battery has been disconnected, first set the time to 1:00 AM, and then set the clock to the correct time

Incoming search terms:

1995 HONDA VFR Owners Manual

0

Filed Under (Honda) by admin on 01-12-2010

download
INSTRUMENTS AND INDICATORS The indicators are contained in the instrument panel. Their functions are described in the tables on the following pages. USA model: Odometer and tripmeter read in miles. Canadian model: Odometer and tripmeter read in kilometers. (1) Speedometer (2) Odometer (3) Left turn signal indicator (4) Side stand indicator (5) High beam indicator (6) Digital clock (7) Tachometer (8) Tachometer red zone (9) Neutral indicator (10) Right turn signal indicator (11) Fuel indicator (12) Fuel gauge (13) Coolant temperature gauge (14) Low oil pressure indicator (15) Tripmeter (16) Tripmeter reset knob 15 (Ref.No.) Description Function ————————————————- ———————————————————– (1) Speedometer Shows riding speed. (2) Odometer Shows accumulated mileage. (3) Left turn signal indicator (Amber) Flashes when the left turn signal operates. (4) Side stand indicator Lights when the side stand is put down. Before parking, check that the side stand is fully down; the light only indicates the side stand ignition cut-off system (page 54) is activated. (5) High beam indicator (Blue) Lights when the headlight is on high beam. (6) Digital clock Shows the time (page 19). (7) Tachometer Shows engine RPM. (8) Tachometer red zone Shows excessive engine rpm range in which operation may damage the engine. (9) Neutral indicator (Green) Lights when the transmissions in neutral. (10) Right turn signal indicator

Hammerhead La Vita 150cc OWNERS MANUAL

0

Filed Under (Hammerhead) by admin on 27-11-2010

download
1. Left and Right rear Mirror 2. Left and Right Brake 3. Front storage compartment (option) 4. Speedometer/ Digital Gauge 5. Main Switch 6. Battery 7. Air Cleaner 8. Seat Lock 9. Rear Light Assembly 10. Left and Right Rear turn Lights 11. Fuel Tank 12. Center Stand 13. Kick Start 14. Side Stand 15. Muffler 16. Left and Right Turn Lights 17. Head Lights 18. Rear Reflector Instrument Panel Speedometer Riding speed is indicated by KM/H and MPH. Odometer The total riding distance is in KM and Miles. The black figures in black background indicate total miles traveled. Indicating lamp or turning light It flashes when turning light is in use. Fuel Gauge Fuel Gauge indicates the remaining fuel in the fuel tank (the gauge does not work when main switch is in the “OFF” position). The gauge moves from “F”(full) to “E” (empty) as fuel decreases in the fuel tank. Fill the tank with 90 Octane or higher gasoline when the needle is approaching the “E” position. There is no reserve tank. Indicating Lamp of High beam It indicates high beam is in use. Note: apply low beam to avoid obstructing the view of oncoming drivers and drivers ahead. 1. Speedometer 2. Odometer 3. Left turn signal indicator 4. Right turn signal indicator 5. High beam indicator 6. Fault signal indicator 7. Battery Gauge 8. Fuel Gauge Instrument Control Main Switch NOTE: – Do not leave the main switch in “ON” position for an extended period of time when the engine is stopped. The battery may drain itself empty. – Lock the steering and remove the key after park to avoid theft. “ON” Position: Electric Circuits are switched on. The engine can now be started. The key can not be removed in this position. “OFF” Position: All electrical circuits are switched off. The engine stops. The key can be removed in this position. “LOCK” Position: The steering is locked when in this position. The key can be removed. Steering Lock Turn the handle bar fully to the left to lock the steering to prevent theft. Push the key in when it is in “OFF” position and while pushing the key in, turn the switch to “LOCK” position to lock the steering. Pull the key out once you are done