Kawasaki Vulcan 500 Receiver Hitch Installation Manual

0

Filed Under (Kawasaki) by admin on 06-05-2012

download
1) Place motorcycle on its side stand on a firm level surface. 2) Remove saddlebags if any. 3) Remove rear riders pegs. 4) Attach front of bracket A (left side) and bracket B (right side) between rear footpeg motorcycle bracket and rear footpeg. Use new bolt provided (Bolt assortment included to accommodate some accessories) 5) Attach bracket E (left side) and bracket F (right side) to two rear fender attachment bolts. Use new bolts provided. (Bolt assortment included to accommodate some accessories) 6) Attach bracket C (left side) and bracket D (right side) to brackets E and F and to second holes on rear of hitch. 7) Attach rear of brackets A and B to BOTTOM of hitch arms 8) Tighten all bolts. Receiver hitch diagram Leveling stand screw jack installation After hitch is installed, install leveling stand screw jacks to hold motorcycle in an upright and level position in order to install or remove InstaTrike. 1) Thread right side screw jack into leveling stand bracket on bracket B and adjust leveling jack bolt out until motorcycle will be level against it. 2) Push motorcycle over from left side until right screw jack is touching floor.

Suzuki Burgman MiniTrike Installation Manual

0

Filed Under (Suzuki) by admin on 17-02-2012

download
installation Checklist Review entire installation manual Remove side/rear cover Modify side cover Install MiniTrike and double check all bolts Replace side/rear cover Align MiniTrike wheels Double check all bolts for tightness Test ride MiniTrike slowly in an open area to familiarize yourself with handling characteristics MiniTrike Installation NOTE: Install all bolts loosely until all brackets are in place. Tighten bolts only after all brackets and bolts are in place Refer to diagram for bracket identification 1. Place scooter on side stand on a firm level surface 2. Remove rear/side panel Refer to motorcycles service manual for questions regarding panel removal. 3. Remove center stand. 4. Drill two frame holes. See figure 1 5. Attach bracket A to the center stand mounting brackets. Place bushings inside of center stand mounting brackets. See figure 2 6. Attach bracket F ( left side ) and bracket G ( right side ) to frame holes drilled in step 4. Be certain to insert bushing into drilled holes and insert bolt through bushing. 7. Attach axels and wheels to MiniTrike and position in proper relation to scooter. 8. Attach bottom of brackets F (left) and G (right) to mounting point on MiniTrike frame 9. Attach bracket D ( left side ) and bracket E ( right side ) to BOTTOM of forward mounting point on MiniTrike frame. 10. Attach bracket B (left side) C (right side) to brackets D/E and to rear of crossbar on bracket A . 11. Tighten all bolts ensuring MiniTrike is square with scooter

Yamaha V-Star 1100 InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 05-01-2012

download
Receiver Hitch Installation y Install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove saddle bags (if applicable) 4) Attach bracket G to underside of motorcycle frame with U-bolts provided. 5) Attach bracket C (left) and bracket D (right) to the two rear fender side attachment bolts between fender and chrome side rail. Use new bolts provided. ( reattach saddle bags now if applicable) 6) Attach bracket E (left) and bracket F (right) to the outside of the rear holes on brackets C and D . Bolt inserts from inside of brackets C and D . 7) Attach bottom of brackets E and F to rear plate on receiver hitch. 8) Attach rear of brackets A and B to TOP of forward arms on receiver hitch. 9) Attach front of brackets A and B to TOP of bracket G 10) Ensure hitch is square on motorcycle and tighten all bolts.
Installation Diagrams
Leveling stand screw jack installation 1) Thread right side screw jack into threaded area on bracket B sand adjust leveling jack bolt out. 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket A and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

Yamaha Virago 750/ 1100 InstaTrike REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 26-12-2011

download
Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand. 2) Attach Bracket A (left) to outside of rear passenger foot peg mount. Place spacers between Bracket A and foot peg mount. Use new bolts provided. 3) Attach Bracket B (right) to outside of rear passenger foot peg. Place spacers between Bracket B and foot peg mount. Use new bolts provided. Bracket will extend over top of mufflers. 4) Attach Brackets C (left) and D (right) to rear frame bolts on
motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A & B and to the TOP of the forward hitch arms. Ensure hitch is square on motorcycle and snug bolts for Brackets A, B, and E,F at this time. 6) Raise rear of hitch so bottom of Brackets C & D are flush with top of rear hitch plate. Ensuring that hitch is square with motorcycle, carefully mark hole locations for bottom of Brackets C&D on rear hitch plate. Drill rear hitch plate holes with 3/8 inch drill. This step ensures proper alignment and spacing of hitch on the motorcycle. 7) Tighten all bolts ensuring that hitch is square on motorcycle. Periodically check bolts for tightness. Bracket Identification
INSTALLATION OF THE TOW-PAC HITCH CART.
1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bo

Incoming search terms:

MOTORCYCLE SERVICE LIFT ADAPTER KIT FOR DYNA TC88 MODELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 28-04-2011

download
Installation A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. 1. See Figure 1. Position the motorcycle on a straight and level surface. While the bike rests on the Jiffy Stand, straighten the front wheel and place the frame leveling extrusion under the front tire to keep the tire straight. 2. Slide the motorcycle lift (fully lowered) under the bike from the right side (opposite jiffy stand side) lining up the frame rails with each of the perpendicular jacking rails on the lift. When properly aligned, the left frame rail will be approximately 1″ from the lift end section (Figure 2) and lift base will be adjacent to the Jiffy Stand (Figure 3). This will allow bike to be centered when moved to an upright position

2001-2002 Honda GL1800/A Frame Weld Inspection PROCEDURE

0

Filed Under (Honda) by admin on 22-04-2011

download
IMPORTANT: During these procedures you may be using and referring to the following materials, originally sent to you with Service Bulletin GL1800 #14. • 2002-2003 GL1800/A Frame Weld Safety Recall Dealer Procedures (S0510) • Frame Weld Inspection Chart (S0516) • 2002-2003 GL1800/A Frame Weld Safety Recall Welding Manual (S0511) • 2002-2003 GL1800/A Frame Weld Safety Recall Cracked Weld Repair Manual (S0515) • Welding Template Box (S0512)If you need additional copies of these materi- als you may order them at no cost from Resolve at (440) 572-0725. 1. Position the motorcycle on a firm, level surface, in an area where there is enough room to safely lay it on its left side. 2. Remove the left side mirror by following the nstructions on page 2-7 of the Service Manual. 3. Remove the left engine side cover by following the nstructions on page 2-5 of the Service Manual. 4. Remove the antenna whip(s). 5. Remove the coolant reserve tank by fol- lowing the instructions on page 6-7 of the Service Manual. 6. Place thick, non-abrasive padding (such as furniture blankets) on the ground to protect the motorcycle when you lay it on its side. 7. Lock the handlebars to the RIGHT, using the ignition key. 8. Using two people, gently lay the motor- cycle down on its LEFT side on the pad- ding. The motorcycle will first rest on the wheels and left engine and saddlebag guards. Continue to lean the motorcycle to the left until it rests on the left handlebar end and left engine and saddlebag guards. The motorcycle should be laying on the padding, with its engine guard, saddlebag guard, and handlebar end resting on the padding – no painted parts should be con- tacting the padding. 9. Clean the frame crossmember with acetone. 10. Draw a line on each side of the grinding template (S0512) 30 mm from the for- ward edge, stopping  between the two arrows, as illustrated below. 11. Put this template on the frame and, using a fine-tipped felt marker (such as a Sharpie), draw a 30 mm line on both crossmember welds. Start this line at the forward edge of the grinding template and stop between the two arrows as shown in the illustration on the next page.Now remove the grinding template

HARLEY DAVIDSON FX SOFTAIL FRONT LOWERING SUSPENSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (T), lockwashers (S), flat washers (R) and axle cap from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) and spacer (O) from fork tube plug (B). Remove quad ring seal (D). Save bolt and spacer but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring -J03923 1 of 4 pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring (1). 11. Remove dust cover (E). 12. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 13. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 14. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). NOTE The lower stop (L) may come out with the damper tube or remain in the slider tube. Ensure that the lower stop is removed from the slider tube. 15. Remove the lower stop (L). 16. Remove damper tube (2) from fork tube. 17. Remove rebound spring (F) from damper tube. 18. Repeat Steps 1-17 for the opposite side fork assembly. Fork Assembly

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

Incoming search terms:

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON XL FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-02-2011

download
REMOVAL Remove Right and Left Forks 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. See the service manual and remove front wheel, fender and brake caliper. 3. Spray glass cleaner on the fork tube between upper and lower fork bracket to lubricate. 1 2 2 is04050 1. Fork cap bolt 2. Pinch bolt Figure 1. Loosen Pinch Bolt 3 2 1 is00154 1. Vise grip 2. Rubber pad 3. Plastic knob Figure 2. Fork Tube Holder (HD-41177) 4. See Figure 1. While holding the fork slider to prevent the fork from dropping, loosen pinch screws (2). 5. Remove fork tube by sliding the fork tube down and out of the upper and lower fork brackets. 6. Repeat Steps 3-5 to remove opposite fork. -J04713 1 of 5
7. Move forks to bench area. Place suitable drain pan on floor beneath vise. Disassemble Left and Right Fork