Harley-Davidson HEAT DEMONS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 27-03-2012

download
1. Remove the Right Handlebar Control, upper and lower switch housing screws, and Right Grip from the Handlebar according to the service-manual instructions and set aside or leave hanging. Remember to insert a spacer between the rear brake light switch and the lever to keep the switch from being broken. 2. Remove the Left Hand switch housing from the handlebar according to the service-manual instructions. 3. Using a T27 TORX drive head remove the half of the clamp that secures the clutch hand lever to the handlebar and discard. The Heat Demon controller will replace this clamp when finishing the installation. Separate the clutch hand lever assembly from the handlebar and move away from the bar. 4. Mark the location of the Left Grip and remove it by twisting, heating or with air pressure. Almost all grips can be removed without damage. If this does not work it may be necessary to cut the grip for removal. 5. A hole needs to be drilled in the bottom of the handlebar to route the power wires and wires from the Controller. The location of the hole should be in the groove or recess on the bottom of the handlebar under the Left Switch Housing at the end of the groove toward the grip. Start by punching a hole location with a center punch to pierce the chrome. Use safety glasses that completely cover the eyes to protect from steel chips while drilling! Start with a small drill like a 3/32″ size to make the initial hole. Then use progressively larger drills or a step drill to increase the hole size to 5/16″. After the hole is drilled use a round file or deburring tool to remove the sharp edges. 6. Uncoil the plastic snake from the kit and run it from the right end of the handlebar out the left end. Twisting the snake or inserting it vertically versus flat can help to push around the corners. 7. Attach the white and yellow wires from the Right Grip Heater (Item 3) to the hole in the plastic snake and pull them through the bar so they exit the left end. (See drawing below) 8. Push the right heater into the handlebar by squeezing it together and sliding it fully inside of the bar. The end of the heater with the orange cap should be pushed in first. Cut the white and yellow wire to extend 4 inches beyond the left end of handlebar. 9. Install the Right Throttle Control and Grip according to the service manua

HARLEY DAVIDSON SPORTSTER ALUMINUM SHIFT LINKAGE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. See Figure 1. Remove stock capscrews (4) and stock shifter rod (2). Discard stock capscrews. 2. See Figure 2 and Table 2. Loosen the lock nuts (5) and turn the rod ends on the new aluminum shifter rod (1) to match the length of the stock shifter rod. 3. See Figure 2 and Table 2. Slide longer capscrew (3) through the front rod end of new shifter rod (1). Place rod on the outside of the lever assembly. Thread capscrew (3) into the lever assembly. 4. Slide shorter capscrew (2) through the rear rod end of new shifter rod (1). Place rod on the outside of the transmission shift lever. Thread capscrew (2) into the transmission shift lever. 5. Tighten capscrews to 10-15 ft-lbs (13.6-20.3 N-m) . 6. Firmly tighten the lock nuts (5) against the rod ends to 20- 24 ft-lbs (27.1-32.5 Nm) . 1 4 2 4 3 is05394 1. Lever assembly 2. Shifter rod 3. Transmission shift lever 4. Capscrew Figure 1. Shift Linkage Components

HARLEY DAVIDSON AILERON HAND GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
LEFT GRIP REMOVAL AND INSTALLATION 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp, and position the clutch hand lever assembly away from the handlebar. 2. Using a T25 TORX drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left hand grip if so equipped. With “glueless” grip: Remove the grip from the han- dlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. NOTE Make sure that the handlebar surface and the inside of the new grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) 4. Position the new left grip (4) so the larger diameter portion of the flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8- 9.0 Nm). 9. Using a T25 TORX drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4.0-5.1 Nm)

HARLEY DAVIDSON SPORTSTER HAND GRIPS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Remove and Install the Left Grip 1. See Figure 1. Using a T27 TORX®drive head, remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar. 2. Using a T25 TORX®drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX®drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9.0 Nm). 9. Using a T25 TORX®drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4.0-5.1 Nm). Remove and Install the Right Grip 1. Refer to the RIGHTHANDLEBARSWITCH section of the service manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLECONTROL section of the service manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the service manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

HARLEY DAVIDSON FLAME HANDLEBAR GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVE AND INSTALL THE LEFT GRIP 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar 2. Using a T25 TORX® drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX® drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9 Nm) . 9. Using a T25 TORX® drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4- 5.4 Nm) . 5 3 1 1 4 2 2 is00735 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger flange Figure 1. Left Handlebar Switch Housing REMOVE AND INSTALL THE RIGHT GRIP NOTE Right handlebar switch removal requires a Service Manual for your model and year of motorcycle. A Service Manual can be purchased from your Harley-Davidson Dealer. 1. Refer to the RIGHT HANDLEBAR SWITCH section of the Service Manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLE CONTROL section of the Service Manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the Service Manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Incoming search terms:

HARLEY DAVIDSON HEATED HAND GRIP KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
REMOVAL Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the fuel tank according to the service manual instructions. -J04259 1 of 8 Left-Side Grip Removal 1. See Figure 1. Using a T-25 TORX drive head, remove the upper and lower switch housing screws (1). 2. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp (3) to the clutch lever bracket. Remove the lower clamp screw with flat washer. Loosen the clamp and position the clutch hand lever assembly away from the switch housing. Separate the upper and lower switch housings. 3. With “glueless” grip: Remove the grip from the handlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. 2 2 1 5 4 3 1 is01283 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger diameter of flange Figure 1. Left Handlebar Switch Housing Right-Side Grip Removal Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 2. 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 2. Using a T-25 TORX® drive head, remove the upper and lower switch housing screws. 3. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp to the brake master cylinder housing. Remove the lower clamp screw with flat washer. Loosen the clamp and position the master cylinder assembly away from the switch housing. Separate the upper and lower switch housings. 4. Remove the grip from the handlebar. NOTES The twist grip sensor in the right side of the handlebar has a seal cap that protects internal electrodes from dirt and moisture, and also serves as a retention device for the throttle grip. To remove the grip, a slight tug may be necessary to release the index pins in the grip from the receptacle in the seal cap. Upon removing the grip, check the location of the seal cap. If the seal cap is still fastened to the index pins inside the old throttle grip, it can be discarded along with the grip. If the seal cap is still fastened to the end of the twist grip sensor: •See Figure 3. Insert a small screwdriver or other flat-blade tool into the flat area on one side of the seal cap. •Press the leg on the underside of the cap to free it from the slot at the end of the twist grip sensor. Pry up one end of the cap. •Repeat on the other side of the cap. •Carefully remove the cap and discard it

Incoming search terms:

HARLEY DAVIDSON HANDLEBAR GRIPS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
INSTALLATION Remove and Install the Left Grip 1. See Figure 1. Remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar. 2. Loosen, but do not remove, the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lb (6.8-9 Nm) . 9. Tighten first the lower, then the upper switch housing screws to 35-45 in-lb (4-5.4 Nm)

DUCATI 1098 DIRECT LEVER INSTALLATION MANUAL

0

Filed Under (Ducati) by admin on 26-10-2010

download
Ducati direct lever sensor installation: 1) Remove original lever assembly 2) Fit the new lever and tight nut. 3) Set toe peg in correct position 4) Connect the sensor with CGS2 and try it: when sensor is pressed a dashes appears on CGS2 SP electronics DUCATI DIRECT LEVER SENSOR INSTALLATION NOTE – The sensor was designed to offer you the best performance and don’t need mechanical maintenance: you mustn’t disassemble or try to repair the lever (See warranty details on our website www.spelectronics.it). – If you intend use our lever sensor with your preferred quick shifter electronic system (Power Commander, Rapid Byke, ecc.) we recommend you to use specific wiring interface (see photo below). Alls connector manipulations on sensor invalidate warranty. SP electronics DUCATI DIRECT LEVER SENSOR INSTALLATION SP electronics is working everyday to improve quality on our products. Unfortunately, perhaps some sensor doesn’t work after some time. Remember that SP electronics will apply warranty substitutions or repairs when products satisfies original complying

Kawasaki Ninja 650R, How to Replace Clutch Springs

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
(Refer to Fig. 1) Take your 4mm Allen wrench and remove the four bolts holding the lower fairing and frame cover in place. Using the flat head screwdriver, remove the three plastic clips from the bottom and front of the lower fairing. Remove the lower fairing by pulling towards you, then down. Remove the frame cover by pulling the bottom towards you to pop the bottom two retaining clips, and then pulling up to pop the remaining top clip. Drain all the oil from the engine, but leave the oil filter in place (unless you plan on replacing it also). Fig. 1 (Refer to Fig. 2 & 3) Remove the throttle adjustment cable from its mount. It just slides right out. Place it out of the way, but do not let it slide behind the engine, as it is a pain to fish out. Removing the clutch cable was quite a job, for me at least. Here’s how I did it: I removed the clutch lever assembly from the handlebars, turned the unit upside down, and removed the cable from the lever. Place the clutch lever assembly to the side. Much of the tension on the clutch release lever should now be gone. Take your pliers and get a good grip on the clutch cable right in front of the clutch release lever. You’re going to have to push the clutch release lever towards the front of the bike as hard as you can; at the same time, you will also have to push the cable away from you and out of the mounting bracket. It took me quite awhile to get it done, but it is do-able this way