HARLEY DAVIDSON DYNA DETACHABLE UPRIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-04-2011

download
INSTALLATION Install Docking Point Kit Install the docking point kit following the instructions in that kit. Passenger Upright Installation 1. See Figure 1. Stand behind the motorcycle, and place (10) the front upright notches (2) into the front docking points (3). 2. See Figure 2. Check for correct notch engagement. NOTE Failure to correctly engage the sideplate notches to the docking points may result in damage to the docking points. 3. See Figure 1. Pull (11) the rotary latches (4) into a rearward position. Align the latches over the rear docking points (7), making sure the latches and rear notches (6) fit into the neck (8) of the rear docking points. NOTE This may require some gentle squeezing or spreading of the upright sideplates. 4. Push downward (12) on the side plates and close the rotary latches by rotating the latch levers as far forward as they will go (13). A click will be heard when the latch is in place. If the latch does not close, do not force it.

HARLEY DAVIDSON SCRIPTED HAND LEVER EMBLEMS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
General Kit 44514-02 is designed for installation on hand lever control kit 45533-02, all other emblem kits are designed for installation on hand lever control kit 45459-02. Installation NOTE When installing the emblems, make sure text is positioned properly. 1. Clean bonding surface on levers with isopropyl alcohol. 2. Remove backing, carefully position emblem and apply steady, even pressure for at least five seconds. 3. Allow 24 hours for adhesive to fully cure

HARLEY DAVIDSON DETACHABLE LOCK KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
REMOVAL 1. Remove the detachable accessory by pressing the release button on each side and pull the latch levers back. Lift the rear of the accessory up and pull the rack off of the front docking points. 2. See Figure 1. Remove the screw (1) and washer (2) from the latch(es) to be replaced by the new locking latch. Save the screw and washer for installation. INSTALLATION See Figure 8. Depending on the installed detachable, the position of the relief (A) and undercuts (B) will be used as spacers or docking point mounts. Verify that the locking latch is positioned so there is key access for unlocking the latch. NOTES Verify that the locking latch is in the unlocked position before installation. Do not leave the key inserted in the locking latch during assembly. Detachable styles may vary from those shown in the illustra- tions. Outer Right Upright Installation 1. Remove right non-locking latch. 2. See Figure 2. Install stock spring washer (2) on mounting hub. 3. Install flat washer (4) (from kit) on mounting hub. 4. Install latch with relief away from the outer right sideplate. 5. Install stock screw (3) and washer (1). 6. Tighten screw to 30-40 in-lbs (3.4-4.5 Nm)

HONDA VALKYRIE ADJUSTABLE PASSENGER BOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Remove the stock pegs using a 14mm wrench on the backside of the peg and muffler mounting plate. NOTE: use the box end of the wrench as these bolts are very tight from the factory. 2. Loosen the two (2) 12mm acorn nuts that attach the mufflers the mounting plate on each side. Next remove two (2) 14mm bolts that attach the plates to the frame on each side. 3. Install the floorboards using the new bolts provided and tighten securely. Tighten the 12 mm acorn muffler mounting nuts on both sides. 4. Pulling the spring-loaded levers out and rotating the lever slightly to hold it in the out position can adjust the Boards. Adjust to the height desired; rotate the levers back to line up with the slots, rock the board and arm slightly so that the spring-loaded pin drops into the nearest hole.

Hot-Start Kit For Yamaha YZ/ WR 400F

0

Filed Under (Yamaha) by admin on 16-12-2010

download
Blaster Rear Brake Kits 121-01298 • YFS200 Blaster ’88-’98 • This cable will eliminate the stock cable from the handlebar. Cable will go from the rear brake pedal to the caliper. 121-01299 • Same as 121-01298 +4″ • Cable is 4″ longer for extended swingarms. 121-01027 Replacement Ratchet Spark Plug Wrench 121-08147 • Designed specifically to fit where there is limited space • Ratchet mechanism works one way • Fits standard 13/16″ plugs
INDEX PAINT HANDLEBARS STREET LEVERS FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS R . 03-15-06 21 (626) 792-7384 www.FlandersCompany.com Fax: (626) 792-5341 www.FlandersCo.com Specialty Tools Swingarm Bearing Tool 121-080213 • Designed for installation of the swing arm bearings on late model Japanese motorcycles • Using the correct size insert (various sizes included in kit) and the puller, the mechanic can draw the bearing into the swingarm without beating on it with a hammer Main Jet Wrenches • High-quality die cast construction • 6mm round and hex jets and 8mm round • Cap holds a few spare main jets • Sold each 121-08023 6mm Hex (Fits 6mm hex main jets) 121-08024 8mm Round (Fits 8mm round main jets) 121-08025 6mm Round (Fits 6mm round main and pilot) Allen Extension 121-080184 • 5mm allen on a 6.25″ long, 3⁄8-drive extension for hard-to-reach case bolts • Designed for use with air tools • Great for splitting engine cases