Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Incoming search terms:

HARLEY DAVIDSON TRIBAR LED TAIL LIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove main fuse. Refer to service manual for location. 2. Remove seat using service manual instructions. 3. Remove rear tail light using service manual instructions. 4. Remove rear turn signals using service manual instruc- tions. 5. See Figure 1. Clip the cable strap (1) to free the rear harness from the chassis seat pan. 6. Unplug the 8-place connector (2) from the rear harness connector. 1 2 is05510 1. Cable strap 2. Harness connector Figure 1. Rear wire harness 1 2 4 3 is05511 1. Screws 2. Fender cover 3. Frame rail 4. Mounting bracket Figure 2. Remove Fender NOTE The fender support covers do not have to be removed from the upper shock absorber bolts. 7. See Figure 2. Remove the two rear fender support cover screws (1) and remove covers (2) and fender mounting -J04721 bracket (4). Repeat for opposite side and carefully remo ve fender and place it on a non-scratch surface. 8. See Figure 3. Clip and remove two cable straps (1). Pull wire harness three inches towards the license plate bracket. 9. Remove flange nuts (2) from both sides of license/tail light bracket stud plates (3) and remove bracket. Save stud plates and flange nuts. 1 3 2 is05517 1. Cable straps 2. Flange nuts 3. Stud plates Figure 3. Rear Harness Cable Straps, Flange Nuts and Stud Plates 10. Install new license/tail light bracket using stud plates and flange nuts previously removed. Tighten nuts to 5-6 ft-lbs (6.8-8.1 Nm) . 11. See Figure 2. Install rear fender by installing two screws (1) on each side through the fender support covers (2), frame rails (3) and into the fender mounting brackets (4). Tighten to 12-18 ft-lbs (16.3-24.4 Nm) 12. See Figure 1. Connect rear harness connector to 8-place connector on main harness. 13. Use a large cable tie strap from kit to secure the rear harness to seat pan. 14. Install rear turn signal lights using service manual instructions. 15. Verify that there is no excess wire harness near the stud plate then secure the harness with a large cable strap where the straps were previously removed. 16. See Figure 4. Secure the turn signal harness (3) to the stud plate (1) using small cable strap (2) and route the turn signal wire through the tail light bracket clip (4) as shown.

BMW R1200RT Sport/ Touring 1100X Kit Installation Manual

0

Filed Under (BMW) by admin on 17-12-2010

download
Step 1 — Locate ‘mold circle’ indentation on each side fairing panel (Pic 1). With panel mounted on bike, this indentation is center, at rear inside panel edge, and faces inside. Temporarily install bracket as shown in (Pic 2), align bottom bracket hole over indentation and mark for hole. Remove brackets at this time. Step 2 — Remove fairing body side panels. Four screws per side required for removal, see owners manual. Drill a 3/8″ hole at mark. If harness kit has not been installed, do not re-install left side panel until finished unless you remove tank to install harness. Removal of the tank is the best option to route harness from battery area to front of the bike. Step 3 — As required, re-install fairing body side panels. Do not re-install the top factory inner panel Torx Screw yet, as you will re-use this screw to secure the top light bracket mounting hole to the fairing panel. Step 4 — Using 10/32×1/2 screws and black shoulder washers from Hardware package, secure lights to PIAA Ezy-Mount® brackets (See Pics 3 & 4). Right side bracket is stamped ‘EZY-MOUNT’. See note below for Powersports lights. Due to close proximity of the light body to fairing side panel, access to the vertical adjustment screw on the panel side of the light will not be possible after installation. To prepare for this; before installing bracket/light assembly to panel, make sure this screw is tightened so that you can barely move the light body. After bracket is installed, final vertical adjustment can be secured with the inside screw. Torque on this screw is adequate to hold vertical adjustment, and the screw that faces the panel will not come loose. NOTE: WHEN INSTALLING POWERSPORTS LIGHTS, YOU MUST INSERT THE SHOULDER ADAPTER WASHER INTO THE LIGHT FOOT, BEFORE INSERTING SCREW TO SECURE LIGHT FOOT TO BRACKET. THIS ADAPTER CENTERS LIGHT FOOT OVER PEMNUT (TIGHTEN THIS SCREW SECURELY). Step 5 — Insert well nut into previously drilled 3/8″ hole. Place bracket assembly against fairing, aligning top hole with the top fairing mounting position; re-install the factory Torx screw at this location. Adjust as necessary and install the second supplied SS 10/32 x 5/8 Torx screw thru the lower bracket mounting hole to the well nut. With constant pressure on the screw, tighten securely. Constant pressure ensures that the rear expandable section of the well nut captures the back of the plastic inner panel as you tighten the screw. Future removal of fairing panels is now possible with light assembly installed (utilizing the bottom bracket mounting screw), thus re-alignment of lights is not required after normal maintenance.

Incoming search terms:

Incoming search terms: