HARLEY DAVIDSON FL SOFTAIL FOWARD CONTROL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 31-03-2011

download
INSTALLATION Shifter Side, Left Block or jack vehicle under frame in a way that the vehicle will not fall over. Failure to properly block and/or raise the vehicle could result in death or serious injury. (00462c) 1. Block the motorcycle under the frame so that it is upright and level, with the weight off of the jiffy stand. 2. Remove footpeg. 3. Remove jiffy stand, shifter linkage and bracket per applicable Service Manual instructions, retaining hardware. 4. See Figure 5. Obtain the new left side shifter bracket (2), and three TORX® screws (3) from the kit. 5. Place washers previously removed on the screws. Apply LOCTITE® 243 (Blue) to the threads, and install the new bracket assembly to the motorcycle frame. Tighten the screws to 40 ft-lbs (54.2 Nm) . 6. See Figure 5. Install footpeg with spring washer (8), clevis pin (10) and retaining ring (9). If leg stop is incorrectly installed, excessive wear can allow vehicle to fall when rested on jiffy stand, which could result in death or serious injury. (00479b) 7. Install jiffy stand and attach the spring. When properly installed, the hook on the spring side connected to the bracket will face upward. 8. Verify that rubber bumper is in place on prong of jiffy stand. Without the bumper, the stand will make hard contact with the primary drive cover when retracted, which may result in damage to the cover. 9. Extend and retract the jiffy stand leg several times to verify proper operation. The stand should swing freely to the fully extended and fully retracted positions. 10. Refer to applicable Service Manual and re-attach the shifter linkage

HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

Incoming search terms:

TRIUMPH ROCKET III HEEL / TOE SHIFTER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Loosen the 10mm nuts at the ends of the shifter linkage rod (notice one end is a left hand thread). Remove the 10mm nut from the shifter arm & disengage the linkage. Remove the shifter pivot bolt using a 8mm hex key wrench. Remove the washer on the threaded side of the shifter pivot bolt. 2. Place one of the wave washers supplied onto the pivot bolt. Place a small amount of grease on the shifter pivot bolt shank and the Heel / Toe shifter pivot hole, insert the pivot bolt into the pivot hole of the toe heel shifter. Use a drop of blue loctite on the shifter pivot bolt threads and install the Heel / Toe shifter, tighten the pivot bolt securely. Check to see that the shifter pivots freely. If the side play is excessive (this is a result of variances in manufacturing tolerances of the stock and supplied components) remove the pivot bolt and install the second wave washer supplied. 3. Unscrew the linkage rod and replace it with the longer rod supplied (NOTE the rod has a left hand thread on one end and right hand threads on the other). Insert the shifter linkage stud into the desired hole in the new shifter being sure the flats on the stud engage the slot on the backside of the bolthole. Install the nut and finger-tighten only at this time. 4. While seated on the motorcycle first find the height setting you prefer for the toe shifter. Using one of the three boltholes for the linkage can set this. You can also gain some adjustment by exposing more or less threads of the new longer shifter linkage rod; however be sue that you have a minimum of 4-5 threads still engaged in the linkage ends. After setting the height, tighten all three 10mm nuts (the two at the ends of the linkage rod and the one which attaches the linkage to the toe/heel shifter) securely. After you have the toe shifter adjusted to your liking you can select the heel shifter height by moving the button head cap screw that secures the toe shifter to the heel shifter (Using a 5/32″ hex key wrench) next to the 10mm linkage nut to any of its three holes

Incoming search terms:

440 Series Shocks Installation Manual

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Follow instructions in an authorized shop manual or take the motorcycle toacompetent dealer. The motorcycle must be on thecenterstand (if equipped) or securely blocked to prevent it from tipping over when the shocks are removed. Failure to do so can cause serious damage and/or injury. The use of any lowering blocks is not recommended and will void the warranty. Make sure that proper bushings/sleeves are installed in the shocks. Improper bushings/sleeves can cause unsatisfactory and/or unsafe operation (seethe instructions packaged with the mounting hardware). 1. Place a quality jack or sufficient blocks under the motorcycle to securely lift the rear wheel slightly off the ground. 2. Using the correct shop manual, remove the old shocks and note location of the mounting hardware. If additional accessories are installed on your motorcycle, please refer to their mounting instruc- tionsforremoval to gain access to your shocks. 3. Before installing your new Progressive shocks you need to check the tire to fender clearance, (see Ain figure1) making sure that the tire does not come in contact with the fender. If the rear fender or tire has been changed to anything other than stock, a travel limiter maybe required. On some models with side bags or luggage, removal of the lower cover maybe required to eliminate any interference. Install shock assemblies onto the motorcycle (shaft end must be down!) and tighten bolts/nuts to proper torque. Check the clearances of the shock to frame (B) and shock to chain, chain guide, disc caliper and linkage (C) in figure 1. The lower cover can be removed for clearance if necessary. 4. Reinstall any accesso- riesremovedin accord with their mounting instructions. Make sure accessories do not in- terferewith shocks throughout full travel. If any accessories bolt to shock mounting points, a careful inspection must be made to insure that they do not bind the shocks in anyway (see figure 2)