Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

Incoming search terms:

KTM 4357/ 4860 MX Multi Adjuster WP Suspension manual Disassembly And Assembling

0

Filed Under (KTM) by admin on 13-02-2011

download
Disassembly forkleg 12_062 12_079Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 5 Frontfork 4357/4860 MXMA 02/2002 Clamp the forkleg (axle-clamp) in the vice and let the outer-tube down. Pull the spring downwards… …and place open-end spanner (size 22) on the hydraulic stop. Unscrew the screw-cap. 12_067 12_068 12_069 12_072Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 6 Frontfork 4357/4860 MXMA 02/2002 Remove the screw-cap from the piston- rod. 12_070 Remove the preload spacers. 12_074 Pull the spring downwards and remove the spanner. 12_075Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 7 Frontfork 4357/4860 MXMA 02/2002 Remove the spring. 12_076 Remove the adjustment tube with the O-ring. 12_089
Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 8 Frontfork 4357/4860 MXMA 02/2002 Clamp the axle-clamp in the vice so that the forkleg is at an angle of ±45 degrees. 12_095 Unscrew the compression holder out of the axle-clamp. (size 19) (when the cartridge is rotating with the holder, bend the piston- rod a little bit to the side) 12_096 Drain the oil out the forkleg. 12_094 Product Exploded View Disassembly & Assembling Workshop manual 4357 / 4860 MXMA 9 Frontfork 4357/4860 MXMA 02/2002 Remove holder compression. Caution: oil iscoming out the cartridge. Disassemble the cartridge out the forkleg. 12_097 12_098 12_099 Disassemble the dust-wiper

Incoming search terms:

2005 HONDA CBR 600RR Superbike BRAKE LINES INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 03-01-2011

download
Step 1: Identify the key components that complete our Super bike KIT, you should have 2 lines (front Kit), and 1 Double banjo bolt and 2 lower adapters. There are also a total of 7 washers, 5 will be used, and 2 are spares. We ALWAYS strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install onto the calipers the Galfer adapter, the course thread area threads to the caliper with one washer. Torque level is 12 to 13 ft pounds. (See picture on adapter A) Step 5: Install right and left lines to the master cylinder, the right line is the shortest out of the two lines. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. (Picture B). This is the sequence on the master cylinder: Master cylinder, washer, straight banjo (from right line), washer, 12 degree banjo (from left line) washer and double banjo hex. Double banjo bolt torque level is 12 FT Pounds . (For positioning see picture G). Banjo 12 on left line must be facing a bit more to the left than the straight banjo of right line, so that the lines can cross at lower triple clamp better. On the calipers, make sure that the 90-degree fittings are pointing out a little bit, thread banjo end to the adapter, torque the end to 6 ½ Ft pounds . (See pictures C, D, E) Before you begin bleeding process, please check for clearance of the lines, push on the front end down, see that the lines are not binding with anything and that when the front end is fully extended or fully under pressure the lines are traveling correctly and clear from any obstructions. Ones the lines have been check for clearance; the two lines are Zip tied together at the same level of the lower triple clamp area. (See pictures F), please make sure that lines cross each other. Step 6: Bleed system, conventional bleeding, pump and release the air from caliper bleed nipples… DOT 4-brake fluid is recommended.

Incoming search terms:

Incoming search terms: