DYNA IGNITION COIL INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 08-11-2011

download
Remove the gas tank. Locate the two ignition coils. 2) Unplug the primary wires coming from the coils and disconnect the high voltage wires from the spark plugs. Remove the coil mounting bolts, and remove the coils. 3) Cut or unsolder primary wires from coils. Crimp or solder ring terminals supplied with kit to primary wires.4) Attach the primary wires to the DYNA COILS using the 10-32 x 5/16 pan head screws provided. Either wire can be mounted on either terminal of the dual output coils as they have no polarity. On the single output coils, the primary terminal opposite the side with the output tower has a + marking. Plus 12 volts from the ignition switch is applied to that terminal, and the points or ignition system output is connected to the other terminal. On a Kawasaki, make sure there is clearance between the screw head and the mounting screw spacer. Do not over- tighten screws as damage to the coil could result. 5) Using the stock hardware, mount the coils to the frame in the original location. NOTE: The DYNA COIL mounting hole spacing is designed to accommodate early model Honda, Kawasaki, and Suzuki motorcycles. There are a wide variety of physical sizes and mounting configurations on the late model motorcycles and it may e necessary to modify existing mounting brackets, or fabricate a bracket to adapt the DYNA COILS to your particular motorcycle

HARLEY DAVIDSON HALF HELMET STEREO HEADSET KIT/ AUDIO CABLE CONNECTION OPERATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
AUDIO CABLE CONNECTION 1. See Figure 3. Obtain the larger clip (4) and the coiled headset audio cable (2) from the kit. Install the 3.5 mm stereo jack end of the cable into the clip. 2. Connect the 3.5 mm stereo jack from the headset audio cable to the audio output socket on the Road Tech riser radio, satellite radio or other audio device. Position the clip in the area indicated in Figure 1, and rotate as needed to allow easy insertion and removal of the cable jack and audio output socket. 2 1 is04347 1. For FLHT models 2. For FXD, FXST, FLST, FLHR and FLTR models Figure 1. Clip Location NOTE Ambient temperature should be at least 60 °F (16 °C) for proper adhesion of the clip to the mounting surface. 3. Clean the clip mounting area with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. 4. Peel the liner from the adhesive backing of the clip. Carefully position the clip to the mounting surface, and press firmly into place. Hold the clip in position with steady pressure for 30 seconds. Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a) •Be sure audio connection harness or headset audio cable do not pinch, bind or interfere when handlebars are turned fully to left or right fork stops. 5. See Figure 3. Use the small clip (5) from the kit to retain any excess headset cable to the side of the console. Attach per Step 4. NOTES Allow AT LEAST 24 hours after applying the clip before exposing the area to vigorous washing, strong water spray or extreme weather. -J04930 1 of 2 PERATION 1. Plug in the coiled audio cable at the headset and audio source. 2. See Figure 2. Put the headset on as shown, with the headband across the back of the head, above the neck. Put the helmet on, and fasten securely

HARLEY DAVIDSON XL SEAT KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1 2 is 00911 1. Tongue 2. Keyhole Figure 2. Underside of 2-up seat INSTALLATION NOTE If installing the seat with a sissybar/backrest pad present, remove the backrest pad prior to seat installation. This will prevent damage to the pad and/or seat. Reinstall backrest pad after the seat is installed. 1. Models equipped with solo seats: See Figure 1. a. Remove the plastic plug (1) from the rear hole location in the fender (2). Save the plastic plug for installation. b. Move the seat retention nut (4) and lockwasher (5) from the middle location to the rear location, where the plug was just removed. As shown in the inset, a cable strap (6) can be used as an installation aid. Place the retention nut (5) over the cable strap so that the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender, and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. c. With the rib of the retention nut (4) seated into the notch in the fender hole, slide the retension washer (5) into place from the rear. This will lock the retention nut in place. d. Reinstall the plastic plug in the fender hole in the middle location. NOTE The foam cushioning of the seat needs to be compressed as the seat is slid forward to engage the post on the frame when the seat is dropped into place. When properly installed, the front tongue on the underside of the seat should fit snugly in the groove at the fuel tank rear mounting location and the keyhole on the underside of the seat will lock the seat to the post on the frame. 2. All models: See Figure 2. a. Angle the front of the new seat into place so the tongue (1) engages the slot at the rear fuel tank mounting location. b. Push the seat forward and rotate the rear of the seat downward until the seat contacts the frame. Flex the seat slightly in the middle and slide the seat towards the rear so that the keyhole slot (2) on the seat bottom engages with the center seat post on the frame. 3. See Figure 3. Pull up on the center of the seat to verify that it is locked into place. (There will be a small amount of play, but the seat should only come up about a half an inch and then will be held firmly in place by the post on the underside of the seat.) If the seat is not firmly in place, repeat Step 2 until the seat is firmly in place. Reference the Owners Manual for further instruction on seat placement if needed

Incoming search terms:

TRIUMPH ROCKET III DRIVER FLOOR BOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 24-12-2010

download
1. Starting on the left (shifter) side remove shifter pivot bolt (large allen head). Rotate the shifter assembly out of the way. Remove the retaining clip from the bottom of the foot peg pivot pin. Remove the pin and the foot peg. 2. Install the left floorboard in the original foot peg mounting location. (Note the L & R markings on the backside of the mounting blocks.) Place the allen bolt (supplied) through the original mount and the floorboard. It may also help to use the shank of a Phillips screwdriver in the bolthole at the same time to help align the holes. In some cases due to variances in the stock foot peg bracket it you may need to use a 25/64″ (.390) drill bit and drill thru both the bracket and the floorboards mounting block to allow the bolt to go thru. The blocks and their holes are machined to exact tolerances and is kept as close as possible to the size of the peg bracket so that there will not be any looseness or drooping of the floorboards when installed. Thread one of the Ny-loc nuts (supplied) onto the bolt and tighten securely. Reinstall shifter assembly and tighten securely. 3. Repeat for right side and re-check hardware for tightness. (The brake assembly will not need to be removed.)