Cadillac Catera 1997 Steering Column Replacement

0

Filed Under (Uncategorized) by admin on 26-05-2011

Download

NOTICE: The front wheels of the vehicle must be maintained in the straight ahead position and the steering column must be in the LOCK position before disconnecting the steering column or intermediate shaft. Failure to follow these procedures will cause improper alignment of some components during installation and result in damage to the SIR coil assembly. NOTICE: Once the steering column is removed from the vehicle, the column is extremely susceptible to damage. Dropping the column assembly on its end could collapse the steering shaft or loosen the plastic injections that maintain column rigidity. Leaning on the column assembly could cause the jacket to bend or deform. Any of the above damage could impair the columns collapsible design. If it is necessary to remove the steering wheel. Under no condition should the end of the shaft be hammered on, as hammering could loosen the plastic injections which maintain column rigidity. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Disable Supplemental Inflatable Restraint (SIR) system. Remove the steering wheel. Remove the SIR coil. Remove the ignition lock cylinder. Disconnect the theft deterrent immobilizer connector. Remove the immobilizer. Remove the ignition switch. Remove the windshield washer switch.

2002-2003 HONDA GL1800 BANK ANGLE SENSOR MOUNTING SCREWS REPAIR MANUAL

0

Filed Under (Honda) by admin on 22-04-2011

download
REPAIR PROCEDURE 1. Insert the ignition key into the lock cylinder and open the fairing pocket lid by turning the key clockwise. Remove the two trim clips by pushing the cen- ter pins in. Remove the two screws. Disconnect the opener  cable and remove the right fairing pocket. 2. To access the bank angle sensor, remove the two mounting screws  securing the connector holder. Place the holder to the side. 3. To check for the proper screw size, slightly tighten both bank angle sensor screws. If the screws are tight, reassemble the unit and apply the identification mark. If the screws spin in the holes, proceed to Step 4. 4. Using a magnetic screwdriver, remove and discard one of the two 4 mm screws securing the bank angle sensor assembly. Replace with a 5 x 12 mm self-tapping screw (see the PARTS INFORMATION section on page 3 for the proper screw for this repair). Repeat for the other screw. 5. Reinstall the removed parts in the reverse order of removal. IDENTIFICATION Apply a white paint dot in the center of the under- side of the right fairing pocket lid as shown. This will indicate that the Safety Recall has been per- formed on this unit

2002-2003 GL1800 BANK ANGLE SENSOR MOUNTING SCREW REPAIR PROCEDURE

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Insert the ignition key into the lock cylinder and open the fairing pocket lid by turning the key clockwise. Remove the two trim clips by pushing the center pins in. Remove the two screws. Disconnect the opener cable and remove the right fairing pocket. 2. To access the bank angle sensor, remove the two mounting screws securing the connector holder. Place the holder to the side. 3. To check for the proper screw size, slightly tighten both bank angle sensor screws. If the screws are tight, reassemble the unit and apply the identification mark. If the screws spin in the holes, proceed to Step 4. 4. Using a magnetic screwdriver, remove and discard one of the two 4 mm screws securing the bank angle sensor assembly. Replace with a 5 x 12 mm self-tapping screw (see the PARTS INFORMATION section on page 3 for the proper screw for this repair). Repeat for the other screw. 5. Reinstall the removed parts in the reverse order of removal. IDENTIFICATION Apply a white paint dot in the center of the underside of the right fairing pocket lid as shown. This will indicate that the Safety Recall has been performed on this unit

BMW Motorcycles F650 CS Parts/ Accessories information

0

Filed Under (BMW) by admin on 12-11-2010

download
1 Hardcase Hardcase Hardcase Hardcase The Hardcase (approx. 10l) is simply “clicked” into the StuffBay. It accommodates everything the rider may need and protects it against theft and water resistance. Easy to install and remove. 71 60 7 664 649 Hard Case w/o lock. 71 60 7 658 463 Lock Cylinder Hardcase Audio System and connecting harness Hardcase Audio System and connecting harness Hardcase Audio System and connecting harness Hardcase Audio System and connecting harness Water resistance hard case protects and equips the F650CS Audio System equipped with a connecting socket for the connecting MD, MP3 or CD player. The sound output from the water-resistance speakers or a helmet output connection— with a speed-dependent volume control. The system is easily “clicked” into place in the StuffBay and removable by the integrated carrying handle. Power harness required and helmet connection, sold separately. 71 60 7 664 650 Audio System 71 60 7 658 463 Lock Cylinder 71 60 7 666 180 Power Harness 71 60 7 670 326 Helmet audio connection (BMW style headset only) Helmet attachment “spider” Helmet attachment “spider” Helmet attachment “spider” Helmet attachment “spider” The helmet attachment “spider” attaches the helmet to the motorcycle and protects it against theft. Ideal for securing a bag or jacket in the Stuff Bay. 71 60 7 664 652 Helmet Strap w/o lock 51 25 2 337 270 Lock Cylinder Oval rear view mirror, chrome Oval rear view mirror, chrome Oval rear view mirror, chrome Oval rear view mirror, chrome—-platedplatedplatedplated The chrome-plated parts give the F650CS an extraordinary look and style. Kit includes left and right mirrors. 71 60 7 669 834 Chrome oval mirror kit. F650CS Accessories Selection F650CS Accessories Selection F650CS Accessories Selection