Harley Davidson DRESSERS TUNED-FLOW SLIP-ON MUFFLERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2012

download
Installing the Tips: 1. Use a long 3/16″ ball drive Allen wrench to remove the two hidden retaining screws. 2. Rotate the tip to the desired position and relocate the retaining screws and lock washers inside the tip. 3. Apply a small amount of anti-seize compound to the threads and tighten to 8 ft./lbs. 4. Check the tip bolts after a brief test ride. Adjusting the Hooker Tuned-Flow® Muffler: 1. Loosen the socket head bolts located in the aluminum ring at the end of the muffler approximately 5 turns using a 3/16″ Allen wrench. Alternate back and forth between each bolt 1/2 turn at a time to keep from binding. 2. Using your fingers, pull the center barrel of the muffler approximately 1/8″ towards the back of the motorcycle and rotate to the desired setting. If warm, use a rag or gloves. 3. By rotating the exhaust barrel and aligning the notch in the barrel with the index marks in the aluminum ring, the power band can be adjusted. The “H” setting will bias the power towards High RPM Horsepower, while the “T” setting will provide more Low RPM Torque. The muffler is infinitely adjustable between these two settings

Incoming search terms:

Harley davidson American Classic Straights on a 1988-2001 VLX 600 Shadow Installation Instructions

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
Remove right side Foot peg assembly or Floorboard. (Whichever is applicable to your model.) 2. Remove bolts that are holding pipes at rear mounting bracket. 3. Loosen clamps at mufflers. 4. Remove mufflers. 5. Remove the two nuts that secure the rear exhaust header pipe to the rear cylinder head. 6. Remove rear exhaust pipe assembly. 7. Remove the two nuts that secure the front exhaust header pipe to the front cylinder head. 8. Remove front exhaust pipe assembly. 9. Remove exhaust-mounting bracket from frame. Hard-Krome Exhaust System Installation NOTE: Take care when fitting this Hard-Krome aftermarket exhaust system on your motorcycle. It has been designed to replace a STOCK exhaust system on a motorcycle with its engine, frame and other components in their STOCK design, configuration and location. WARNING : Re-check and re-tighten ALL fasteners and supports after 50 miles, then re-check and tighten as necessary on a periodic basis to ensure proper operation and performance. NOTE: All fasteners should be loose during initial installation to ensure proper fit and location of the new exhaust system.
1. Install new exhaust gaskets. 2. Install mounting bracket using Bolts with flat & lock washers. (See Illustration) 3. Install Front exhaust header pipe, taking care to not scratch chrome surfaces on pipe, engine or motorcycle — use masking tape as needed. 4. Install the two nuts to secure the flange that holds the exhaust header pipe to the front cylinder head — DO NOT TIGHTEN NUTS! 5. Install nut strip into slotted bracket of front pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 6. Carefully install rear pipe. 7. Install the two nuts to secure the flange that holds the exhaust header pipe to the rear cylinder head — DO NOT TIGHTEN NUTS! 8. Install nut strip into slotted bracket of rear pipe and start the 3/8-16×3/4″ Bolt with flat & lock washer through backside of mounting bracket. — DO NOT TIGHTEN BOLTS! 9. Tighten the two bolts that secure the rear exhaust header pipe flange. 10. Tighten the two bolts that secure the front exhaust header pipe flange. 11. Tighten front pipe bolts at mounting bracket. 12. Tighten rear pipe bolts at mounting bracket. 13. Reinstall foot peg assembly or floorboard. 14. If applicable to your model install foot peg relocating brackets and foot pegs as shown in illustration. 15. Before starting bike wipe off any fingerprints and grease off pipes. Start bike and check for any exhaust leaks.

Incoming search terms:

Harley-Davidson FL Caliper Mount Installation Manual

0

Filed Under (Harley Davidson) by admin on 26-02-2012

download
Motolight® Caliper mounts are designed to be mounted on the brake caliper mounting boss. Before removing the caliper bolt make certain you have the manufacturer’s recommended torque settings for your make, model and year. 2 . Disconnect your battery. Never work on the electrical system of a motorcycle while the battery is connected. If you’re not sure how, check your owner’s manual, or consider having your dealer install the lights. 3 . Motolights®, like any light, get hot when operating. Do not touch any part of the housing when the Motolights® are in operation and for at least 15 minutes after they have been turned off. 4 . If you are transferring your Motolights® to another bike or have obtained the lights secondhand, it is VERY IMPORTANT that you contact us at 800-567-8346 or 513-474-7530 for new caliper bolts of proper grade and size. Step 1. Unpack the Motolight® system . Take this chance to familiarize yourself with everything. Below is the list of included items: Item # Quantity Description 1 (2) º” x 20 x 5/8″ stainless steel socket head cap screws 2 (2) Housings, aluminum, assembled with lens, lamp and leads 3 (2) Mounting blocks, aluminum, left and right 4 (2) Caliper replacement bolts 5 (2) Lock washers 6 (1) Motolight wiring harness with relay and 20 amp fuse 7 incl. Special Harley auxiliary plug connector in wiring harness (included) 8 (2) Motolight decals (1 helmet size, 1 regular) 9 (1) Aiming tube (cardboard ring) 10 (1) 3/16″ hex wrench 11 (1) Pin wrench (for standard lamp retaining rings-not required for knurled/grooved rings) 12 (15) Cable ties, long and short

HONDA GL1800 BACKREST (INSERT) INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 04-03-2011

download
1. Place motorcycle on center stand. 2. Remove the two passenger handles and seat. 3. Install the base mount between the seat mounts (picture 1) and mark the two holes on seat base. 4. Drill two 9/32″ holes in the seat base. 5. In the middle of the two seams and in the center of the seat, install the boot (picture 2). 6. With a long serrated knife cut a hole in the seat inside the boot opening. You must clear a path in the foam from the cut to the two 9/32″ holes. 7. Insert the long bar through the hole into the seat from the outside with the hole tube facing forward (picture 3). 8. Bolt the base mount to the long bar using bolts and lock washers. 9. Attach the chrome pad mount to the long bar protruding through seat (picture 4). 10. Attach the pad to the pad mount with the mounting bracket (picture 5). 11. Reinstall the seat and adjust the pad angle (picture 6). Reattach passenger handles

HARLEY DAVIDSON V-LOGO REAR FENDER TRIM RAIL INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
INSTALLATION NOTE All models for which this kit is designed are equipped with a original equipment (stock) fender rail or bumper. Remove the stock bumper and install the kit rail using following the proce- dures. 1. See Figure 1 and Table 1. Install V-logo (4) to trim rail (1) with hex washer screws (3) and lock washers (2). 2. Reach under rear edge of fender and remove locknut (A) and washer (B). Retain locknut and washer and use to mount new trim rail. 3. Loosen and remove the two screws (C) and locknuts (D) which attach fender rail to saddlebag support bracket. Retain screws (C) and locknuts (D) and use to mount new trim rail. 4. Place new trim rail in position and install washer (B), locknut (A), screws (C) and locknuts (D). 5. Tighten locknut (A) to 45-85 in-lbs (5.0-9.6 Nm) and locknuts (D) to 15-20 ft-lbs (20.3-27.1 Nm) . SERVICE PARTS 2 3 4 1 A B C D is05379 Figure 1. Service Parts: V-Logo Rear Fender Rail Table 1. Service Parts Part Number Description (Quantity) Item Not Sold Separately Trim rail, rear fender 1 7115 Lock washer (2) 2 7611 Hex washer screw (2) 3 91112-94 V-logo 4 Items mentioned in text, but not included in kit. Locknut (2) A Washer (2) B Screw (2) C Locknut (2)

HARLEY DAVIDSON PULLBACK RISER KIT FOR 1.25-INCH HANDLEBARS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVAL NOTES Cover the fuel tank with clean shop towels to prevent scratching. If replacing the handlebar, refer to the service manual to remove controls, hand levers, handlebar and risers. If only the risers are being replaced, proceed as follows: 1. Remove the two hex head cap screws and split lock- washers on the underside of the upper fork bracket that hold the currently installed risers in place. Discard the screws, but retain the lockwashers for assembly. Retain all additional components from the riser assembly when the screws are removed. 2. Remove and discard the four screws that fasten the currently installed handlebar upper clamp(s) to the risers. Remove and discard the clamp(s). Remove the handlebar from the risers and carefully set the handlebar on the fuel tank. INSTALLATION NOTES See Figure 3. The upper cup washer (A) must be oriented with the flat side up and the lower cup washer (D) with the flat side down. 1. See Figure 3. Align the components as shown, and install the risers (2) to the upper fork bracket. The ground wire (G) and the lock washer (F) are located on the right side only. Do not tighten the riser mounting screws (4) at this time. 2. If an appropriate Harley-Davidson 1-1/4 inch handlebar has not been installed, install one according to the Instruction Sheet included with the kit, or install the handlebar assembly onto the risers. 3. Loosely install riser caps (1) onto the handlebars and risers with the Bar & Shield toward the front of the motorcycle (Figure 1, Item 1). Install four socket head screws (3) with four washers (6). 1 is05253 1. Bar & Shield (install toward front of motorcycle) Figure 1. Bar & Shield on Riser and Cap 4. Check that the risers stay properly aligned with the handlebar and tighten the riser mounting screws following the instructions in the service manual. 5. Adjust handlebar to the desired position, verify that it is centered on the risers, then tighten the front socket head screws (3) to 12-15 ft-lb (16-20 Nm) . There should be no gap at the front of the risers.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL RIGID MOUNT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
INSTALLATION NOTE Maximum saddlebag load is 10 lbs. (4.5 kg) for each bag. Do not exceed saddlebag weight capacity. Put equal weight in each bag. Too much weight in saddlebags can cause loss of control, which could result in death or serious injury. (00383a) NOTE Saddlebag hangers must be mounted with the bend in the hanger facing out from the motorcycle. NOTE The saddlebags are symmetrical and can be mounted on either side. 1. See Figure 1. Remove the fender support cover screws from locations shown for mounting saddlebags. 2. Place lock washers (6) on two cap screws (5) and insert through the top holes of the saddlebag hanger. NOTE The FXSTC Does Not use narrow spacers (8) in Step 3 for the saddlebag installation. 3. With the cap screws in place on the hanger, place a wide spacer (7) followed by a narrow spacer (8) on each screw. 4. Thread the cap screws into the location of the original screws previously removed in Step 1 and tighten screws to 22 ft-lbs (30 Nm) . 5. From the inside of the saddlebag install two button head screws (2) with washers (3) through the upper mounting holes in the saddlebag and the hanger. 6. On the backside of the hanger install hex nuts (4) to the screws from previous step and tighten to 22 ft-lbs (30 Nm) . 7. Insert two button head screws through the lower two holes on the backside of the hanger and into the saddlebag. 8. From the inside of the saddlebag install washers and hex nuts to screws and tighten to 22 ft-lbs (30 Nm) . 9. Repeat Steps 1 through 8 for installation of the other saddlebag. Installation with Docking Points 1. If you choose to use the docking points from Kit 53930- 03, repeat the installation of previous Steps 1-8 and substitute the front and rear docking points for the spacers (7) in this Kit. You must use narrow spacers (8) from this kit for both the FLSTSB and the FXSTC when using the docking points. Install Reflectors

HARLEY DAVIDSON SLOTTED HANDLEBAR RISER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION NOTE Cover the fuel tank with a clean shop towel to prevent scratching. Damage to the finish could result. 1. Remove the two hex head cap screws and split lock- washers on the underside of the upper fork bracket that hold the currently installed risers in place. Discard the screws, but retain the lockwashers for re-assembly. Retain all additional hardware components that become dislodged from the riser when the screws are removed. 2. Remove and discard the four screws that fasten the currently installed handlebar upper clamp(s) to the risers. Remove and discard the clamp(s). Remove the handlebar from the risers, and carefully allow the handlebar to rest on the fuel tank. 3. Obtain the new slotted risers (1) and hex head cap screws (2) from the kit, and the split lockwashers and hardware components removed in Step 1. NOTE The upper cup washer (A) must be oriented with the flat side up , and the lower cup washer (D) with the flat side down . The ground wire (G) and internal tooth lockwasher (H) are mounted to the right-side riser. 4. Refer to Figure 1 for the correct orientation and reassembly sequence. Install the new risers onto the upper fork bracket using the saved hardware and new screws. Snug the riser screws, but do not fully tighten at this time. 5. Center the handlebar on the risers. To make sure that the handlebar is centered, verify that the knurled areas on the outboard side of each riser are equal. 6. Position the new handlebar upper clamps (3) from the kit, and install with new hex socket head screws (4). Snug the upper screws, but do not fully tighten. Improperly aligned handlebars can contact the fuel tank when turned to the left or right. Contact with the fuel tank can cause cosmetic damage. (00372a) 7. Slowly turn the front wheel to the full right fork stop and then the full left fork stop to be sure the handlebar does not contact the fuel tank. If contact occurs and the handlebars are properly centered, raise the handlebar angle as necessary until proper clearance is attained. 8. Tighten the upper handlebar-clamp screws as follows: a. Tighten the front screws to 12-15 ft-lbs (16-20 Nm) . b. Tighten the rear screws to 12-15 ft-lbs (16-20 Nm) . c. Tighten the front screws to 12-15 ft-lbs (16-20 Nm) . NOTE The gap between the upper clamps and the risers should be equal at the front and rear of the handlebar after tightening. 9. One at a time, remove the riser bolts installed in Step 4. Apply two drops of Loctite® 271 (Red) to the bolt threads and re-install. Tighten the riser bolts to 50-60 ft-lbs (68-81 Nm)

Incoming search terms:

VICTORY HAMMER, KINGPIN, VEGAS AND JACKPOT ELECTRIC HORN INSTALLATION INSTRUCTIONS

0

Filed Under (Victory) by admin on 29-01-2011

download
1. Remove the left and right plastic side covers and the seat (two allen bolts located below the sides of the seat). Unplug and remove the stock horn (located over the oil cooler). Connect the female ends of the jacketed two wire cable supplied to the original horn wires. Route the other end of the cable up over the engine and back to where the relay will mount as shown in photo (1). 2. Using the relay supplied with this kit and the wiring diagram provided with the horn set, identify the terminals of the relay (there are very small numbers next to each of the terminal). Connect the two (2) wires from the cable to terminals #85 & 86 on the relay. Locate the fuse holder wire assembly supplied and connect the blade terminal to the relay terminal #87 or #30. Connect the other end of the fuse wire to the battery positive terminal (+). 3. Working under the left side of the motorcycle, refer to photo (2) and install the black bracket supplied as shown onto the engine mount. Locate the four thin flat brackets and two (2) 6mm nuts supplied with the horn set and two lock washers supplied with the kit. Bolt two (2) of the brackets to each of the horns using a lock washer and 6mm nut on each and make them snug. Using the remaining 6 x 12mm bolt, nut and lock washer install the horns onto the black bracket and align as shown in photo (3). Adjust the horn location so that they are free to vibrate and do not come in contact with other parts of the motorcycle then tighten all three 6mmm bolts securely. 4. Using the two remaining wire assembles supplied, connect the larger terminals with double wires to one of the horns and the terminals with the single wire to the other horn. Route these wires up thru the frame to the relay. Connect the wire with the female blade connector to the relay terminal #30 or #87. Connect the ring terminal to the battery negative (-) terminal
or any 6m bolt on the frame. Turn on the ignition and test the horns. Secure the relay to the frame or other wiring and all loose wires using the cable ties supplied. Replace the seat and side covers

Incoming search terms:

TRIUMPH AMERICA AND SPEEDMASTER PASSENGER FLOORBOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 25-12-2010

download
1. Remove the 12mm nuts located behind the stock foot peg assemblies and remove the peg sets. 2. Starting on the left side locate the left floorboard assembly and left round chrome spacer block. These will be stamped with an” L” on the back side. Insert two of the 3/16″ x 1/2″ dowel pins supplied into the two holes where the foot peg was mounted at one o’clock and seven o’clock. Place the spacer blocks backside (stamped with the L) onto the pins 3. Place two more of the dowel pins in the holes on the outside of the block using the holes at twelve o’clock and six o’clock. Place the left floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. 4. On the right side install two more of the dowel pins supplied into holes where the foot peg was mounted at eleven o’clock and five o’clock. Place the remaining spacers backside (stamped with an R) onto the pins 5. Place the remaining two dowel pins supplied into the holes of the spacer block at six o’clock and twelve o’clock. Place the right floorboard assembly onto the spacer block and pins so that it is parallel to the ground or horizontal (this will be the holes closest to six and twelve o’clock on the backside of the floorboard assembly). Insert one of the 5/16″ x 2″ socket head bolts into the center-mounting hole. Place one of the 5/16″ washers, lock washers and nuts onto the bolt and make finger tight. Recheck to be sure the floorboard is parallel to the ground. NOTE; if you are also installing the TA005-5 relocation arms, follow those instructions next. Finally be sure to tighten all bolts securely

Incoming search terms: