HARLEY DAVIDSON VENTED FAIRING LOWERS KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1. See Figure 1. From the kit, obtain the left side fairing lower (1), left side fairing lower cap (2), two flange locking nuts (3) and two stud clips (4). Place fairing lower cap in front of the left side engine guard and left side fairing lower behind engine fairing guard. With both pieces in place around engine guard, install the two flange locking nuts onto the studs clips and hand tighten. Repeat procedure for right side fairing lower. 2. Secure bottom of fairing lower to lower engine guard with round clamp (5) from hardware kit. Position clamp around engine guard with tabs toward rear of vehicle and flat side of clamp against fairing lower and with the rubber washer (6) between clamp and engine guard. Place Torx pan screw (7) through fairing lower, rubber washer and clamp. Secure assembly with flanged locknut (8). Repeat for right side fairing lower. Tighten to 144 in-lbs (16.3 Nm). 3. Tighten all left and right side upper flange locking nuts (3) to 72 in-lbs (8.1 Nm). 4. Install left side door assembly glovebox (9) to fairing lower using the attachment cord (10). Insert glovebox door into fairing lower. Repeat for right side fairing lower. NOTE Do not press reflector firmly into place until you have it positioned in desired location. The adhesive is very strong and once it comes in contact with a surface, it will be difficult to remove without damaging the reflector. 5. Peel adhesive strip off back of reflector from kit. Position reflector on side of front fender above chrome side trim strip and approximately 4 inches rearward from front of fender. Press reflector securely into place. Repeat for opposite side reflector

Incoming search terms:

INDIAN MOTORCYCLES footboard cover Installation

0

Filed Under (Indian) by admin on 31-10-2010

download
INSTALLATION Tools – Drill and 1/4″ bit – 5/32 Hex Key (included) – 7/16″ Wrench – Needle Nose Pliers 1. Use needle nose pliers to loosen footboard cover and rotate forward out of the way. 2. Using the HEEL GUARD as a template, place in rear corner of metal base plate. Be careful to align the rod with the inside edge of the base plate. Mark the holes first. 3. Drill 1/4″ holes. Print Instructions
Heelguard Installation 4. Use the enclosed bolts and locking nuts to secure the HEEL GUARD. 3. Reinstall the footboard cover

2000-2007 BMW F650GS Adapter Installation Manual

0

Filed Under (BMW) by admin on 26-10-2010

download
1. Remove both of the rear stock luggage rack screws with a Torx wrench. 2. Install the Rear Frame Grabber by sliding it up under the rear fender and in front of the stock luggage rack mounting tabs. 3. Attach the Rear Frame Grabber with the 2 replacement M8 screws (stock ones are too short). The tabs on the Rear Frame Grabber should face outward toward the rear of the bike (see A in picture). Torque both screws to 110in.lbs. 4. Install the Rear Adapter as shown. 5. Attach the Rear Adapter with 2 5/16 Button Head Screws. Torque both screws to 110in.lbs. 6. Remove the motorcycle seat and remove the 2 torx screws shown in the picture. 7. Install Frame Grabber Nuts under the passenger grab bar mounts. The long end of the nut goes to the rear of the motorcycle. 8. Support the nut under the mount with your fingers and attach the Front Frame Grabber with a 5/16 Button Head Screw. 9. Reinstall the Torx screws to attach the plastic side cover of the motorcycle. There will be some overlap of the plastic cover and the Front Frame Grabber. 10. Install the Front Adapter. 11. Attach the Front Adapter with two 5/16 Button Head Screws and Locking Nuts. Snug but don’t tighten the screw until after you have installed the Front Main Arm. 12. Reinstall the Seat and compartment cover. Depending on the year of your motorcycle you may need to push the rear of the seat forward to get it around the Front Adapter. It’s a close fit, but it will fit. A B D J C E F G H F

Incoming search terms: