HARLEY DAVIDSON BADLANDER SEAT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
Installation When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat strap from motorcycle. Retain all hardware. Discard seat strap. 2. Remove existing seat from motorcycle by removing Phillips head screw with lockwasher, and nylon washer from rear fender mounting bracket. Retain all hardware except discard nylon washer. 3. Disengage seat from frame tab at front of seat. 4. Install new seat onto motorcycle, making sure bracket on front of seat fully engages into seat mounting tab on frame. NOTE On rear fenders of 1997-1999 models, a captive nut secured with a plastic retention washer has replaced the previously used weld nut. Do not remove the plastic retention washer unless the captive nut is damaged and must be replaced. The plastic retention washer also prevents seat bracket from contacting paint on fender. Therefore, no nylon washer is required between bracket and fender on 1997-1999 models. 5. On pre- 1997 models , secure seat onto rear fender with original screw and lockwasher and place guide washer (1) between seat bracket and rear fender. 5a. On 1997-1999 models , secure seat onto rear fender with original screw and lockwasher. After installing seat, pull upward on front of seat to be sure it is locked in position. If seat is loose, it could shift during vehicle operation, resulting in loss of control of vehicle and death or serious injury. 6. Use original hardware to install new seat strap (2) in same location as old seat strap. On FXSTC, Softail Custom models, fasten seat strap to fender support

HARLEY DAVIDSON ENGINE-GUARD MOUNTED FOOTPEGS (CHROME WITH RUBBER INSERT) INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
Installation Footpegs must be positioned so rider can operate all foot controls throughout their range of motion without interference. Failure to have full, unlimited access to foot controls could cause loss of control, which could result in death or serious injury. 1. See Figure 1. Remove the bolt (6) and lockwasher (5) from the footpeg assembly (1). NOTE When installing the footpegs on a 1 inch (25 mm) diameter engine guard, use both clamps. . For 1 inch (25 mm) dia. engine guards: Place both the large clamp (2) andthe small clamp (1) around the engine guard as shown. Position the clamps on the straight, upright section of the guard. For 1-1/4 inch (32 mm) dia. engine guards: Discard the small clamp (1). Place the large clamp (2) around the engine guard. Position the clamp on the straight, upright section of the guard. 2. For ALL engine guards: Install two step spacers (4) inside the clamp on either side of the engine guard as shown. 3. Put the lockwasher (5) on the bolt (6). Insert the bolt through the clamp and spacers, and thread into the footpeg assembly as shown. Mount the footpegs so they will not strike the ground during cornering. Footpegs striking the ground during cornering could result in death or serious injury. 4. Position the footpeg for rider comfort, and rotate the footpeg assembly so it folds upward and to the rear. Tighten bolt (6) to 30 ft-lbs (41 Nm) so the footpeg does not rotate on the bar. 5. Repeat Steps 1 through 4 for the right side

HARLEY DAVIDSON DYNA DOCKING HARDWARE FOR FXDX WITH WIDE TIRE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
Installation NOTE Perform the following procedures on one side of the motorcycle until instructed to go to the other side. To keep fender in alignment the front docking point will be mounted first. INSTALLING DOCKING POINTS NOTE Save the acorn nuts and washers removed from the fender support bracket for use when installating docking points. 1. Loosen and remove the acorn nuts, washers, and screws from the fender support (right-hand) bracket. Save the washers and acorn nuts for docking point installation. Discard screws. 2. Obtain 1 plastic bushing, labeled 01, from a bushing set. 3. Place the bushing (4) (beveled side out) into the front support hole as shown in Service Parts illustration. 4. Place the countersunk side of the front docking point (2) so that it engages bushing (4). 5. From underneath (inside) the fender, insert hex-head screw (1) through fender, support bracket and front docking point (2). 6. Install washer (7) split lockwasher (5) and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 7. Obtain another plastic bushing, labeled 01 , from the bushing set. 8. Place bushing (4) (beveled side out) into the the rear support hole as shown in Service Parts illustration. 9. Place the countersunk side of the rear docking point (3) so that it engages bushing (4). 10. From underneath (inside) the fender, insert hex-head screw through fender, support bracket and rear docking point (3). 11. Install washer (7) split lockwasher (5)and acorn nut (6) to screw and tighten to 27 ft-lbs (37 Nm). Take care to avoid scratching or marring component finish. 12. Repeat procedures 1 through 11 for opposite (left-hand) side of the motorcycle. NOTE In time docking points may wear, causing the sideplates to become loose. The fit may be tightened using the following procedure. 1. Loosen docking hardware. 2. Rotate docking points clockwise approximately 45°. 3. Tighten docking hardware to the appropriate torque values. Repeat as often as required, up to 3 times

Incoming search terms:

HARLEY DAVIDSON PASSENGER FOOTBOARD INSERT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
INSTALLATION If replacing an insert or inserts on a vehicle currently equipped with Swept Wing Passenger Footboards: Existing Footboard Insert Removal NOTE Carefully remove the currently installed footboard insert to avoid damage to chrome surfaces. 1. See Figure 1. Fold the passenger footboard (1) into the UP position. 2. Loosen, but do not remove the footboard insert setscrew (2). 3. With the footboard folded DOWN, carefully raise an outside corner of the existing insert with a suitable flat-bladed tool, taking care to avoid damaging the chrome footboard pan. 4. Continue around the insert, using a second tool if necessary to pry the existing insert (3) from the footboard pan. 5. If replacing both inserts, repeat for the opposite footboard. Swept Wing Passenger Footboard Installation 1. If installing inserts on a vehicle NOT currently equipped with Swept Wing Passenger Footboards: •Remove currently installed passenger footboards (if so equipped) per the instructions included with the Swept Wing Passenger Footboard Kit. •Remove currently installed passenger footpegs (if so equipped) by removing the socket screw with lockwasher retaining the footpeg support bracket to the rear fork (swingarm) bracket. 2. Follow the instructions in the Swept Wing Passenger Footboard Kit to install the passenger footboards. Footboard Insert Installation 3. ALL applications: Center the two footboard pivot pins. 4. Use soapy water to moisten the rubber dowel pins and pivot pin slots on the bottom of the new footboard insert. 5. Place the insert into position with the rubber dowel pins mating the holes in the footboard pan. Firmly press the insert into the footboard until the dowel pins pop into place. 6. Fold the passenger floorboard UP and tighten the setscrew to secure the insert. 7. Repeat Steps 3 through 6 for the opposite footboard. NOTE Avoid the contact of chrome surfaces with abrasive materials (stones, sand, etc.) as damage will result

HARLEY DAVIDSON TLE/TLE-ULTRA SIDECAR ATTACHMENT KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
REMOVAL NOTES Refer to the service manual for more information on these generalized steps. Save all removed parts (unless otherwise noted) for installation of this kit or for motorcycle operation without the sidecar. 1. For TLE-Ultra Models: Remove both lower fairings. 2. Remove the bolt and lockwasher securing the right passenger footrest bracket and remove the bracket with footrest. 3. Remove the three right side exhaust heat shields. Some models may require removal of the right side exhaust pipes. 4. Remove stock clutch cable. 5. Remove rear master cylinder/rear brake pedal assembly. Remove rear brake pedal from master cylinder assembly. Remove and save rubber pedal pad and brake pedal. Discard cotter pin. 6. Cut the cable straps holding front oxygen sensor connector to frame bracket. 7. Remove wire harness/brake line clip from right lower frame tube. INSTALLATION New Clutch Cable Installation 1. Refer to the service manual and follow instructions to remove stock clutch cable. 2. Refer to the service manual and follow instructions to connect the new clutch cable to clutch hand lever. 3. For FLHT/C/CU: Follow the instructions in the service manual to route new clutch cable through fairing. 4. For FLHR/C Models: Capture the cable in a clamp at the left upper passing lamp bolt. On FLTR models, capture the cable in a clamp at the left upper bolt securing the speedometer and tachometer housing to the upper fork bracket. These locations are identical with stock cable routing. 5. See Figure 1. Route clutch cable down along left frame downtube (1). 6. Continue to route cable down between left front engine isolator and crankcase. Clutch cable will cross to the right side of motorcycle beneath the crankcase, to the clutch release cover on the right side of the transmission. 7. Install clutch cable fitting into clutch release cover. Refer to the service manual. NOTES The final positioning and attachment of the clutch cable and clutch cable adjustment will be performed after sidecar mounts have been installed. Verify that the clutch cable and the rear brake line do not make contact. Damage could result. 1 2 3 is05785 1. Downtube 2. Clutch cable 3. Route clutch cable behind left front engine iso- lator Figure 1. Route Clutch Cable Relocating Oil Pressure Sending Unit NOTES Perform this procedure on all models equipped with an oil pressure gauge or Police models. All other models proceed to “Master Cylinder Assembly/Rear Brake Pedal Modification.” 1. Remove cable strap securing oil pressure wire harness to frame. 2. Locate the latch on connector to oil pressure sender (next to lower right frame downtube). Raise latch on connector and disconnect connector from oil pressure sender. 3. Remove the oil pressure sender using a 1-1/16 inch open- end crowfoot wrench. 4. See Figure 16. Coat threads of elbow (44) with Loctite 565 and install into crankcase oil pressure sender threads. 5. See Figure 2. Install elbow (1) until snug so open end is in the five-o’clock position (2). Do not over-tighten or crankcase may be damaged. 6. Coat threads of oil pressure sender with Loctite 565 and install into 90 degree brass elbow. Use a 1-1/16 inch open- end crowfoot and tighten to 96-120 in-lbs (11-14 Nm) . 7. Install connector on oil pressure sender unit. Verify that slight clearance to the right engine isolators is present. Adjust position of elbow as required to provide clearance

HARLEY DAVIDSON KING TOUR-PAK WRAP AROUND LIGHT UNIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the negative battery cable (-) following the instructions in the owner’s manual. 2. Locate the two-sided template (part number 50002-01) printed on a 11 x 17 inch sheet of poster board. Cut out the template as indicated. 3. If the motorcycle is radio equipped, separate the antenna cable from terminal at antenna base. Remove the nut, lockwasher and ground ring terminal from antenna terminal. Remove phillips head screw threaded into antenna base. Remove mast and antenna base. Detach mast from antenna base by turning counterclockwise with adjustable wrench across flats. 4. See Figure 10. Shield threads of antenna terminal stud with strip of light cardboard. Remove terminal with pliers across cardboard strip. Save terminal and mast for later installation. 5. See Figure 1. Open Tour-Pak top and remove all loose contents. Remove Tour-Pak. Align the template as follows: a. Place center line template (4) along rear top edge of Tour-Pak (1) with curved end against one corner. b. Mark centerline at top edge of Tour-Pak. c. Reverse center line template and mark center with curved end against opposite corner. d. If centerlines overlap, mark center one half the distance between the two lines. e. Place a square against lip at top of Tour-Pak and draw a 3 in (76 mm) line down from the center mark

HARLEY DAVIDSON BILLET HEADLAMP WITH SHORT/ TALL MOUNTS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Kit 68593-06 is a 5-3/4 inch headlamp and kit 69851-06 is a 4-1/2 inch headlamp. Both kits will fit the models listed in Table 1. Table 1. Short and Tall Mount Kits Models Kits 1984-1999 FXSTC, 1998- Later FXST/B, and 2000-Later FXSTD; 1994-2005 FXDWG Short Mount Kit 68595-06 1996-Later XL 1200C and 1998-Later XL 883C; All 2006 Dyna Models; 1999-2000 FXR2/3/4 Tall Mount Kit 69611-06 Additional Parts Required This kit also requires the separate purchase of a Short or Tall Mounting Kit 68595-06 or 69611-06 for your model motorcycle, and can be purchased from a Harley-Davidson dealer. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson dealer. Kit Contents See Figure 21, Table 2 and Figure 22, Table 3. REMOVAL Remove Headlamp and Mounting Bracket for Softail Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative (-) battery cable. 2. Remove fuel tank. Refer to FUEL TANK in Service Manual. 3. Disconnect 4-place headlamp connector [38] from main wire harness. Headlamp connector is located under fuel tank on left side. 8 5 7 5 6 2 1 3 4 is01835 1. Screw 2. Washer 3. Nut 4. Lockwasher 5. Washer (2) 6. Screw 7. Mounting block 8. Headlamp assembly Figure 1. Softail and Dyna Headlamp Assembly with Mount (except FXSTD) NOTE All Softails (except FXSTD) complete steps 4 through 6. For FXSTD models complete steps 7 through 9 4. All Softails (except FXSTD): See Figure 1. Remove screw (1) and washer (2) from stem and bracket. Discard screw but save washer for later use. 5. Remove and discard mounting block (7) and headlamp assembly (8). 6. FXSTD models: See Figure 2. Remove screw (1) and washer (2) from stem and bracket. Save screw and washer for later use. 7. Remove and discard nut (3), washers (4), and screw (5). 8. Remove and discard mounting block (6) and headlamp assembly (7). 7 3 4 2 1 4 6 5 is01838 1. Screw 2. Washer 3. Acorn nut 4. Washer (2) 5. Screw 6. Mounting block 7. Headlamp assembly Figure 2. FXSTD Headlamp Assembly with Mount Remove Headlamp and Mounting Bracket for Dyna Models 1. Remove seat following the instructions in the Service Manual. 2. Disconnect negative (-) battery cable. 3. Remove fuel tank. Refer to FUEL TANK in Service Manual. 2 1 is01750 1. Cable strap 2. Wire harness Figure 3. Dyna Service Loop (2005-Earlier) 4. 2005-Earlier FXDWG: See Figures 3 and 4. Remove plug on right side of top frame tube. At service loop, remove cable clip and push wire harness into top frame tube. Pull connector out from hole on right side of tube. 2006-Later FXD: See Figure 5. Remove cover under top frame tube, then pull connector out from opening under tube. 5. Disconnect 4-place headlamp connector [38] from main wire harness

Incoming search terms:

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON STREAMLINER PASSENGER FOOTBOARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
REMOVAL 1. See Figure 1. Remove existing passenger footpegs or footboards, brackets and mounting hardware. 1 4 3 2 is04325 1. Screw and washer 2. Bracket 3. Footpeg mount 4. Footpeg pad and bottom Figure 1. Passenger Footpeg Components (FLHX) INSTALLATION NOTES • If necessary, remove any paint from counterbore holes of footboard brackets to ease the installation of the pivot pins. • On 2010 and Later Models: The installation height can be adjusted to one of three positions. To install footboards in a new position, remove plastic plugs from holes in rear swingarm bracket as necessary. • On 2009 and Earlier Models: The lowest of the four holes on the frame is not threaded and cannot be used to mount the footboards. 1. See Figure 2. Insert shoulder bolt (9) or (10) through slot in footboard bracket (1). a. 2010 and Later Models: Thread the 5/16 inch shoulder bolt (9) into the lowest hole in the rear swingarm bracket of the frame. b. 2009 and Earlier Models: Thread the 3/8 inch shoulder bolt (10) into the second lowest hole in the rear swingarm bracket of the frame. Tighten the bolts to 48-72 in-lbs (5-8 Nm.) . 2. At the desired height, install the upper screw (2) and lockwasher (3) through footboard bracket (1). Tighten screw to 36-42 ft-lb (49-56 Nm) . 3. Install spring (4) into retaining hole in footboard bracket. Set the ball (5) on top of spring. 4. Position the detent in the bottom of the footboard pan (8 or 12) over ball in footboard bracket. Be sure not to unseat the ball. Press down on footboard pan so the holes of the footboard pan and footboard bracket align. 5. Insert pivot pins (7) through two mounting holes on footboard bracket and into footboard pan. 6. Align footboard insert (6 or 11) in footboard pan. Press insert firmly until the footboard pan tabs are firmly seated in the footboard insert. 7. Fold footboard up and install set screw (13) to secure footboard pad. 8. Pivot footboard assembly up and down to verify proper operation. 9. Repeat all steps for opposite side

HARLEY DAVIDSON RIDER BACKREST KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION 1. 1988-1990 models: Remove saddlebag covers from both sides of vehicle. 2. Remove seat mounting bolt(s), one for 1991-later and two for 1988-1990 models. Note hardware sequence for reassembly. 3. Remove seat according to the instructions in the Service Manual. 4. Remove and discard two bolts securing handrail mounting plate to rear fender. NOTE Check nut threads in fender. Some 1994 and later models have coarse threads (5/16-18). Make sure the 5/16-18 x 7/8 in. bolts are used in these applications. Attempting to use fine thread bolts (5/16-24) in coarse holes or coarse thread bolts in fine thread holes will damage threads in holes and on bolts. 5. 1998 and earlier models: See Figure 1. Obtain two 5/16- 24 x 7/8 in. bolts (5) (or 5/16-18 x 7/8 in. bolts on some 1994 and later models). Add one flat washer (6) and one lockwasher (6) to each bolt. 1999 models: Continue with Step 5. These models will not use Items 5 or 6. 6. Position backrest mounting bracket (7), with tab toward front of vehicle, over holes in handrail mounting plate. NOTE See Figure 2. Four holes are provided in each side of backrest mounting bracket for adjustment purposes. Use set of holes best suited for riding position