Yamaha 1998 XVS1100 REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 03-01-2012

download
EXPLODED DIAGRAMS To help identify parts and clarify procedure steps, there are exploded diagrams at the start of each removal and disassembly section. 1. An easy-to-see exploded diagram 4 is provided for removal and disassembly jobs. 2. Numbers 5 are given in the order of the jobs in the exploded diagram. A number that is enclosed by a circle indicates a disassembly step. 3. An explanation of jobs and notes is presented in an easy-to-read way by the use of symbol marks 6 . The meanings of the symbol marks are given on the next page. 4. A job instruction chart 7 accompanies the exploded diagram, providing the order of jobs, names of parts, notes in jobs, etc. 5. For jobs requiring more information, the step-by-step format supplements 8 are given in addition to the exploded diagram and the job instruction chart.
24 21 18 15 16 17 10 12 13 11 14 1 3 5 7 9 2 4 8 6 19 20 22 23 25 EB003000 ILLUSTRATED SYMBOLS Illustrated symbols 1 to 9 are printed on the top right of each page and indicate the subject of each chapter. 1 General information 2 Specifications 3 Periodic inspections and adjustments 4 Engine 5 Cooling system 6 Carburetion 7 Chassis 8 Electrical 9 Troubleshooting Illustrated symbols 10 to 17 are used to identify the specifications appearing in the text. 10 Can be serviced with engine mounted 11 Filling fluid 12 Lubricant 13 Special tool 14 Torque 15 Wear limit, clearance 16 Engine speed 17 Ω, V, A Illustrated symbols 18 to 23 in the exploded diagrams indicate the types of lubricants and lubrication points. 18 Apply engine oil 19 Apply gear oil 20 Apply molybdenum disulfide oil 21 Apply wheel bearing grease 22 Apply lightweight lithium-soap base grease 23 Apply molybdenum disulfide grease Illustrated symbols 24 to 25 in the exploded diagrams indicate where to apply locking agent 24 and when to install new parts 25. 24 Apply locking agent (LOCTITE) 25 Replace

Incoming search terms:

HONDA GOLD WING GL1800 Independent Suspension Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 23-27psig. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. If you want to check the oil level, do so by removing the fill plug on the top of the differential housing (Remove seat) and by using a suitable measuring device, the oil level should be 5 1/4″ inch down from the top of the differential housing. Refill as necessary. Change the differential oil every 30,000 – 35,000 miles by draining it and refill with 2 quarts of above gear oil.. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Rear brake pads are Volkswagen Part # D101P. 6. Drive Train . The rear driveshaft U-joint and slip yoke spline are fitted with grease fittings, pump the fittings with wheel-bearing, graphite or high-pressure grease every 3,000 to 5,000 miles. The front u-joint does not have grease fittings. 7. Suspension System : The suspension is a Double A-arm Independent suspension with a standard single setting anti-roll bar or an optional Variable Sway Control (VSC) which can be adjustment for optimal ride, handling characteristics and performance. The A- arms are equiped with bushings that does not require servicing. The suspension system is designed to give you the best ride with a load of no more than 600 pounds (passengers plus cargo plus trailer tongue weight): 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals

Incoming search terms:

HONDA GOLD WING GL1500 AND GL1800 TRIKE CONVERSION KIT Owner's Maintenance Notes

0

Filed Under (Honda) by admin on 16-02-2011

download
1. Tire Pressure and Rotation : Keep the nominal tire pressure at about 20-25 psi. It is not necessary to periodically rotate the trike tires unless you experience unusual tire wear. 2. Bearing Lubrication . Your Swing Arm and wheel bearings are sealed and do not require greasing. However, should you experience unusual wheel bearing noise you should take your trike to a Champion Trike Dealer or to your motorcycle mechanic for a checkup. 3. Body Lubrication . There are no grease fittings on the trike body and no required body lubrication points. 4. Rear end lubrication . Your differential comes filled with 1 quart of SAE 85W140 API GL-6 gear oil. You should not have to top-off the differential unless you experience axle seal or pinion seal leaks. Check the oil level every 10,000 miles, or sooner if you experience leaks, and refill as necessary. Do not fill higher than the fill-hole. Change the differential oil every 30,000 – 35,000 miles. 5. Brakes . Check your front and rear brake system fluid levels every 3,000 miles and top-off as necessary. Inspect brake pads every 10,000 miles and replace as necessary. Pads are Volkswagen Part # D101P. 6. Drive Train . If your driveshaft U-joint and/or splines are fitted with grease fittings, pump the fittings with wheel-bearing, graphite or high-pressure grease every 3000 to 5,000 miles. If yours does not have grease fittings then lubrication is not required. 7. Suspension System : The suspension system is designed to give you the best ride with a load of no more than 500 pounds (passengers plus cargo plus trailer tongue weight): GL1500: The OEM adjustable air shock is used in conjunction with two (2) new Progressive 416 air shocks. The three shocks should be pressurized to about 20 psig, but to no more than 70 psig; GL1800: You can still use your OEM mono-shock pre-load adjustment. Your two (2) new coil-over shocks do not have an air system connection. However, there is a pre-load adjuster ring on each new shock that is factory-set at the “lowest” setting, for the softest ride. Changing this setting will result in a stiffer ride. 8. EZ-Steer (rake kit) : If your trike is equipped with Champion’s EZ-Steer, the bearings are a wear item. You should follow your motorcycle manufacturer’s recommended front-end triple-tree maintenance requirements. Generally these call for an initial service at 1,000 miles followed by periodic maintenance at 10,000 mile intervals. 9. Electrical : Your trike is pre-wired for a trailer connection. The harness is just below the trunk door on the underside of the body.

Incoming search terms:

KYMCO MAXXER 300/ 250 MONGOOSE 300/ 250 SERVICE MANUAL

0

Filed Under (Kymco) by admin on 26-10-2010

download
apply or add designated greases and lubricants to the specified lubrication points. ÑAfter reassembly, check all parts for proper tightening and operation. ÑWhen two persons work together, pay attention to the mutual working safety. ÑDisconnect the battery negative (-) terminal before operation. ÑWhen using a spanner or other tools, make sure not to damage the motorcycle surface. ÑAfter operation, check all connecting points, fasteners, and lines for proper connection and installation. ÑWhen connecting the battery, the positive (+) terminal must be connected first. ÑAfter connection, apply grease to the battery terminals. ÑTerminal caps shall be installed securely. 1 . GENERAL INFORMATION 1-6 ATV 300/250 ÑIf the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. ÑAfter operation, terminal caps shall be installed securely. ÑWhen taking out the connector, the lock on the connector shall be released before operation. ÑHold the connector body when connecting or disconnecting it. ÑDo not pull the connector wire. ÑCheck if any connector terminal is bending, protruding or loose. Confirm Capacity 1 . GENERAL INFORMATION 1-7 ATV 300/250 ÑThe connector shall be inserted completely. ÑIf the double connector has a lock, lock it at the correct position. ÑCheck if there is any loose wire

Incoming search terms:

Incoming search terms: