HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

Incoming search terms:

HARLEY DAVIDSON DETACHABLE PASSENGER BACKREST LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-04-2011

download
INSTALLATION 1. See Figure 1. If not already assembled in package, assemble V-logo onto each mounting bracket (2 and 3) using #4-40 thread-forming screws (5). 2. Position luggage rack between sideplates of detachable passenger backrest assembly. 3. Thread button head screws (7) through washers (6), then through holes in luggage rack support and passenger backrest sideplate and into mounting brackets (2 and 3). Apply LOCTITE 243 (Blue) to screws (7) before installation. Finger tighten. 4. Tighten button head screws to 19 ft-lbs (26 Nm) . NOTE The backrest shown in Figure 1 is not included in this kit and must be purchased separately. -J01851 1 of 2 SERVICE PARTS 8 1 7 6 3 2 4 5 is04290 Figure 1. Service Parts: Detachable Passenger Backrest Luggage Rack Kit Table 1. Service Parts Table Part Number Description (Quantity) Item Part Number Description (Quantity) Item 2711 Screw, #4-40 thread-forming, steel, zinc plated (4) 5 Not sold separately Passenger backrest rack kit 1 94066-90T Washer, chrome (4) 6 53046-00 Bracket, mounting, right side (includes items 4 and 5) 2 94392-92T Button head screw, hex socket, chrome (4) 7 53045-00 Bracket, mounting, left side (includes items 4 and 5) 3 Not Sold Separately Warning label 8 Not sold separately V-logo (2) 4

HARLEY DAVIDSON FLSTC SOFTAIL SADDLEBAG KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 16-04-2011

download
Additional Fitment Information Detachables NOTE If motorcycle has not been altered from fixed saddlebag hardware to accessory mounting detachable docking points. the separate purchase of Turn Signal Mounting Bar (Part Number 68611-98) is required for sufficient lock clearance. This kit is available at your Harley-Davidson Dealer. Installing these saddlebags on models equipped with a detachable sissy bar or detachable luggage rack requires the additional purchase of mounting hardware kit as follows: Hardware Kit Fitment 53075-03 2003 and later FLSTC models with detachables 53009-03 1987 through 2002 FLSTC models with detachables See Service Parts Page for kit contents. Additional weight can affect motorcycle stability, handling characteristics, and safe operating speed. Do not exceed 7 lbs. (3.18Kg) maximum load in each saddlebag. Evenly distribute weight between each saddlebag. Improper loading can cause vehicle handling problems leading to death or serious injury. Wide Tire If a wide tire kit has been installed, utilize the hardware and installation instructions found in that kit to reorient the fasteners to come from the inside to the outside of the finder. Button head screws from wide tire kit must be installed from the inside out, with the button heads on the inside of the fender. Failure to do so could result in bolt contacting tire, which could result in death or serious injury. Installation NOTE A Service Manual for your vehicle is available at your Harley-Davidson Dealer. 1. Remove seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. (00048a) Disconnect the negative (-) battery cable first. If positive (+) cable should contact ground with the negative (-) cable connected, the resulting sparks may cause a battery explosion which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative cable first. 3. Following instructions in applicable Service Manual, remove original saddlebags from supports. Install Turn Signal Mounting Bar If motorcycle is not equipped with accessory mounting detachable docking points, install Turn Signal Mounting Bar (Part No. 68611-98) following instructions provided with the kit. See Figure 1

Incoming search terms:

HARLEY DAVIDSON CONTOURED TOUR-PAK LUGGAGE RACK KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-04-2011

download
INSTALLATION NOTE The location of the Tour-Pak spoiler has a direct relationship to the location of Tour-Pak mounted luggage rack. The spoiler template will locate the Tour-Pak spoiler in the correct position for the luggage rack so that the spoiler may be added in the future. It is recommended that the spoiler be installed first. See Figure 1. 1. Identify if the installation of a Tour-Pak mounted spoiler is desired in the future. Use the template if the spoiler will be installed. Cut the template along the appropriate line. Carefully place template on top of Tour-Pak lid, aligning edges of template with top surface of Tour-Pak. Tape template in desired location. 1 is 00579 1. Check clearance between rack and spoiler Figure 1. Tour-Pak Rack and Spoiler NOTE Position top rack with upright section toward rear of motorcycle. To avoid contact with the passenger backrest pad, do not mount the top rack in too far forward a position. 2. See Figure 2. Place the four mounting pads (1) onto the four mounting supports on top rack (2). Carefully center the rack on the lid and position the rack rear supports 5/8 inch to 3/4 inch (16 mm to 19 mm) in front of the emblem on the Tour-Pak lid, as shown. 1 is 00636 1.5/8 in. – 3/4 in. (16 mm – 19 mm) Figure 2. Locate Holes From Emblem 3. Use a grease pencil to temporarily mark the positions of the four mounting pads on Tour-Pak cover. NOTE Apply masking tape to the Tour-Pak cover painted surface at the four points where the top rack mounting holes will be drilled. The tape can be marked for hole location, and will help prevent the paint from being chipped during the drilling procedure. 4. Carefully remove top rack/mounting pad assembly. Place a strip of masking tape over each grease pencil mark on the Tour-Pak cover. Once again, position top rack/mounting pad assembly on Tour-Pak cover in the desired mounting location. 5. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting pad. Remove top rack/mounting pad assembly. Use a ruler to mark the exact center of each circle drawn on the tape strips. NOTE Remove all contents from within the Tour-Pak to avoid possible contact with the moving drill bit during the following drilling procedure. 6. Drill starter holes using a 1/16 inch drill bit. Drill the finished holes for the mounting screws using a 9/32 inch drill bit. Remove masking tape strips. 7. Apply a small amount of silicone sealant around each mounting hole on interior surface of Tour-Pak cover

Incoming search terms:

HARLEY DAVIDSON XR1200 LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 29-03-2011

download
Kit 53976-08 (XR1200 Passenger Upright Kit) is available for separate purchase. Contact your Harley-Davidson dealer for more information. Kit Contents See Figure 2 and Table 1. REMOVAL 1. Remove pillion and seat following the instructions in the appropriate Service Manual. 2. Remove the seat base following the instructions in the appropriate Service Manual. 3. See Figure 1. Remove the turn signal mounting screws (3) and discard. Allow the turn signal to hang by the harness until lower bracket installation. 4. Remove the rear fender support strut screws (6) and dis- card. INSTALLATION 1. See Figure 2. Install lower luggage rack mount bracket with screws (9), flat washers (10) and nuts (8). Bracket will mount around nut (Item 2 in Figure 1). Tighten to 19 ft-lbs (26 Nm) . 2. Install screws (7) and nuts (8) through the rear fender support strut and the lower luggage rack mount bracket. Tighten to 19 ft-lbs (26 Nm) . 3. Route the turn signal wire harnesses through the groove in the bracket. Install new turn signal mounting screws (11). Tighten screws to 3-5 ft-lbs (4-7 Nm) . 4. Install seat base following the instructions in the appropriate Service Manual. 5. Install upper luggage rack mount bracket (4) with original equipment seat base screws in the lower holes (A). Do not tighten at this time. 6. Install screws (3) into slotted holes in the upper luggage rack mount bracket (4) and flange nuts (6). Slide the upper bracket as far back in the slots as possible. Tighten screws (3) to 10 ft-lbs (13.5 Nm) 4 1 1 2 5 6 3 is05250 1. Lower luggage rack mount bracket screw (4) 2. Nut (2) 3. Turn signal mounting screw (4) 4. Upper luggage rack mount bracket 5. Luggage rack 6. Rear fender support strut screw (2) Figure 1. Luggage Rack Installation NOTE If installing the Passenger Upright Kit (part number 53976-08) (available separately), do not install spacers (2) and screws (3) in front holes. 7. Install luggage rack (1) aligning the holes with the holes in the upper luggage rack mount bracket. Install spacers (2) and screws (3) in holes. Tighten to 6-10 ft-lbs (8-13.5 Nm) . After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 8. Install pillion and seat following the instructions in the appropriate Service Manual. Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a

Incoming search terms:

HARLEY DAVIDSON PASSENGER PILLION UPRIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
INSTALLATION 1. See Figure 1. Install the luggage rack following the instructions in the kit. 2. Insert the ends of the upright (2) into the pillion (3) (purchased separately) and align the holes in the upright with the holes in the pillion. 3. See Figure 2. Apply LOCTITE 243 to screws (2) and install with washers. Tighten screws to 84-108 in-lbs (9.5-12.2 Nm) . 4. Install the pillion and upright assembly onto the luggage rack following the instructions in the detachable passenger pillion kit. 1 2 3 4 is05507 1. Passenger backrest pad (optional) 2. Passenger pillion upright 3. Detachable pillion (purchased separately) 4. Luggage rack (purchased separately) Figure 1. Upright SERVICE PARTS 3 1 2 is05508 Figure 2. Service Parts: Passenger Pillion Upright Table 1. Service Parts: Passenger Pillion Upright Kit Part Number Description (Quantity) Item Not Sold Separately Passenger pillion upright 1 3787 Screw, 1/4-20 x 0.75 inch (4) 2 6703

HARLEY DAVIDSON VRSCF LUGGAGE RACK KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
REMOVAL 1. See Figure 1. Remove four rear fender mounting bolts (1) and washers (2). If necessary, move the ECM to access the four fender mounting bolts. 2. Disconnect the tail lamp following the instructions in the appropriate service manual. 1 2 is05463 1. Bolt (4) 2. Washer (4) Figure 1. Fender Mounting Bolts INSTALLATION NOTE There are bosses molded into the inside of the fender to use as the hole drilling templates. 1. See Figure 2. Apply masking tape to the outside painted surface of the fender at the three hole locations (1 and 2). This will protect the painted surface during the drilling operation. 2. Put the fender on a work bench, painted surface down. Use clean, soft cloth between the fender and the work bench to protect the paint finish. NOTES Drilling each hole in the fender is a two-step procedure that requires a specific type of drill bit to avoid damaging the fender. 3. See Figure 2. Use a 1/2-inch spade bit or 1/2-inch unibit (do not use a spiral-type drill bit) to drill three holes from the inside of the fender through the three pilot hole bosses (1 and 2). Stop drilling when the tip of the bit just pierces the outside surface of the fender. 4. Turn the fender over so the painted surface is now facing up. Complete each hole by using the same 1/2-inch drill bit at each of the pierced holes. Clean excess material from the holes and clean the fender surface of any debris. 5. See Figure 5. Remove the masking tape from the holes and apply the protective tape (3) to the painted surface using the drilled holes for alignment. 6. See Figure 3. Put the luggage rack (1) upside down on the work bench and align the holes in the luggage rack with the holes in the fender (2).

HARLEY DAVIDSON VRSCF RIGID SADDLEBAGS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Kit Contents See Figure 5 and Table 1. PREPARATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. 2. Remove the rider seat and passenger pillion per the instructions in the service manual. 3. See Figure 1. Remove the four rear fender mounting bolts (1) and washers (2), and the passenger grab strap (3). If necessary, move the ECM to better access the fender mounting bolts. 1 3 2 is05463a 1. Bolt (4) 2. Washer (4) 3. Grab strap Figure 1. Fender Mounting Bolts 4. Disconnect the six-way tail lamp socket housing and four- way turn signal lamp socket housing from the vehicle main harness following the instructions in the service manual. Disconnect the two-way license-plate illuminator socket housing from the tail lamp harness. 5. If a luggage rack, sissy bar upright or both have been mounted on the rear fender , remove the two screws and washers, and two carriage bolts and nuts that secure the luggage rack bracket to the seat pan. NOTE The rack and/or upright will remain attached to the rear fender when the fender is removed. 6. Remove the rear fender from the seat pan by lifting upward and sliding the fender back. 7. If a center-mounted license bracket is installed, it can remain attached to the seat pan. If a side-mounted license bracket is installed: a. Remove the license plate from the vehicle (if installed), and set aside for later installation. b. See Figure 2. Remove the two bolts (8) holding the side license-plate bracket (1) to the seat pan (9). c. Remove the license-plate adjuster bracket (2) carriage bolt (3), washer (4) and lock nut (5), and the license- plate illuminator (6) and screws (7) from the bracket. d. The original equipment (OE) license-plate bracket (1), screws (7) and bolts (8) can be discarded. Set the remaining items aside for installation to the new side license-plate bracket. 8. Remove and discard the rear side reflectors (10). If a center-mounted license bracket is installed, remove the reflectors from the license bracket sides. Remove any residual adhesive from the bracket. If a side-mounted license bracket is installed, remove the reflectors from the upper frame just forward of the shock absorbers. Remove any residual adhesive from the reflector mounting area on the frame. NOTE Access to the shock absorber adjustment collar is more difficult with the saddlebags in place. 9. Adjust the rear suspension preload, if desired, per the instructions in the service manual

HARLEY DAVIDSON FXSTD PASSENGER BACKREST AND LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) INSTALLATION Passenger Upright 1. Unscrew the captive screw fastening the seat rear bracket to the fender. 2. Remove the rubber plugs from the three holes in the rear fender where the passenger upright installs. 3. See Figure 2. Fasten the studplate (2) to the fender (A) with the backing plate (3) and three flange locknuts (4). 4. See Figure 1. Fasten the passenger upright (3) to the studplate (1) with three flange locknuts (2). 5. Insert the seat front bracket into the frame, then fasten the seat rear bracket to the fender. NOTE The seat must be temporarily bowed up in the center to fit the seat rear bracket through the slot in the passenger upright. 6. Kit 51144-02 only. See Figure 2. Carefully clean the lower hole (B) on the passenger upright (1) with isopropyl alcohol to remove any grease or dirt. Remove backing from adhesive emblem (5) and press the emblem firmly in to place. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 1 4 3 2 is03890 1. Stud plate 2. Locknut, flange (3) 3. Passenger upright 4. Backrest pad Figure 1. Passenger Upright, Backrest Pad and Luggage Rack Installation NOTE When temporarily removing the passenger upright, the mounting and backing plates may be left in place to simplify passenger-upright re-installation. Thread the flange nuts back onto studs to store the nuts. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) Backrest Pad See Figure 2. Fasten the backrest pad (7) to the passenger upright (1) using the button-head screw (6) as shown. Luggage Rack NOTE See Figure 2. Fasten the luggage rack (8) to the backrest with the backrest pad (7) removed from the studplate (2). -Fasten the luggage rack (8) to the passenger upr ight (1) using the luggage-rack mounting plate (11), button-head screw (12)

Incoming search terms:

HARLEY DAVIDSON SOFTAIL DETACHABLE TWO-UP TOUR-PAK LUGGAGE RACK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download

TOUR-PAK LUGGAGE INSTALLATION TO RACK 1. Open the lid and, if necessary, remove all items from inside the Tour-Pak luggage.  Remove the rubber mat from the luggage floor. 2. If holes ARE NOT pre-drilled in the floor of the luggage,       see Figure 1. To prevent damage to the leather while drilling, place blocks of wood underneath the Tour-Pak luggage at the drilling sites.  Use the four inboard holes (3) in the metal base of the luggage (2) as a guide, and carefully drill four 11/32 inch (9 mm)  holes through the floor of the luggage. 1 2 3 is04249 1. Front of motorcycle 2. Tour-Pak 3. Drill four 11/32 inch (9 mm) diameter holes Figure 1.  Drill Attachment Hole Locations in Tour-Pak NOTE See Figure 3. When installing the luggage to the rack in the following steps, note that holes in the luggage rack (2) provide forward (A) and rearward (B) positions for mounting the lug- gage. 3. Place the luggage on the luggage rack.  Align the holes in the luggage mounting plate with the forward or rearward holes in the rack. 4. ALL applications: Obtain the hex head cap screws (9), lock nuts (11) and plain washers (10) from the kit. Place a washer over the threads of each screw, and insert the screw threads, from the inside, through the Tour-Pak luggage mounting plate and floor, and into the holes in the rack. NOTE Always install the mounting screws from inside the luggage.  If the screws are installed from the bottom, the screw ends can tear the rubber mat and scratch objects, such as helmets, stored inside the luggage. 5. From the underside of the rack, install a washer and lock nut onto the threads of each screw.  In a crosswise pattern, incrementally tighten each screw to 19 ft-lbs (25 Nm) . 6. Install the rubber mat into the luggage.  Close and latch the lid. 7. If not already in place, install the Detachable Docking Hardware Kit to the vehicle per the instructions in that kit

Incoming search terms:

Incoming search terms: