HARLEY DAVIDSON DETACHABLE TOUR-PAK LIGHT HARNESS KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Models with main FUSE: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. 2. ALL models: Install the Detachable Tour-Pak Rack Kit per the instructions in that kit, up to the point where the saddlebags are to be re-installed. NOTE Make note of the cable strap locations before releasing the harness from the upper frame tube. New straps will be fastened in the same location. 3. Cut the larger cable strap fastening Tour-Pak circuit [12] (see the Service Manual Wiring Diagram) of the vehicle main harness to the left-side upper frame tube, rearward of the shock absorber. Cut the small cable strap at the end of the circuit [12] conduit. 4. Slit the conduit open along its length to expose the final ten inches (0.25 M) of main harness circuit [12] wiring. Cut the three wires (Black, Blue, and Red with Yellow tracer) nine inches (0.23 M) from the three-way Multilock socket housing [12B]. The socket housing and cut wires can be discarded. 5. Obtain the socket housing, secondary lock (locking wedge), and three socket terminals from the kit. See the illustration at DEUTSCH ELECTRICAL CONNECTORS: REMOVING/INSTALLING SOCKETS in the Service Manual. Refer to CRIMPING INSTRUCTIONS in the Service Manual, and follow the instructions to install the terminals to the three wire leads of main harness circuit [12]. 6. Per the instructions under DEUTSCH ELECTRICAL CONNECTORS, insert the Blue lead and terminal into Cavity 1 of the new socket housing. Insert the Red/Yellow lead and terminal into Cavity 2. Insert the Black lead and terminal into Cavity 3. 7. Cut the excess conduit from main harness circuit [12]. 8. Obtain the two cable straps from the kit. As noted in Step 3, use one strap to bind the end of the main harness circuit [12] conduit. Use the second strap

HARLEY DAVIDSON ILLUMINATED CHROME COVER KIT FOR FAIRING MOUNT MIRRORS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION Preparation Models with main fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. Models with main circuit breaker: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the service manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. Installation NOTE Cover the work surface with an H-D Service Cover or clean shop towels to prevent scratching the finish of the outer fairing. 1. Remove the outer fairing per the instructions in the service manual. Lay the fairing face down on a sturdy work sur- face. 2. See Figure 2. Remove the mirrors (2), flange nuts (3) and plastic backing plates (4) securing the mirrors to each side of the inner fairing (1), and retain all items 3. Measure one inch (25 mm) straight down (5) from the large mirror stud hole in the inner fairing, and make a mark. 4. Drill a 1/4 inch (6 mm) diameter hole (6) through the inner fairing at the mark. 5. See Figure 1. Obtain a chrome wire collar (3) from the kit, and press it into the new hole from the outside of the inner fairing. Gently tap into place with a soft-faced hammer. 6. Repeat Steps 3 through 5 on the opposite side of the inner fairing. NOTE Ambient temperature should be at least 50 °F (10 °C) for proper adhesion of the mirror cover to the mirror. 7. Clean the back surface of the mirrors with the alcohol pad (7) provided. Allow to dry thoroughly. 8. Obtain the primer tube (8) from the kit, and follow the instructions on the tube to activate the primer. When the primer is activated apply the primer to the back surface of one mirror. 3 6 2 1 4 5 is06091 1. Inner fairing 2. Fairing mount mirror 3. Flange nut (2) 4. Plastic backing plate (2) 5. Measure one inch (25 mm) down 6. Drill 1/4 inch (6 mm) hole (2) Figure 2. Fairing Drill for Illuminated Mirror NOTE The Illuminated Chrome Mirror Covers are side-specific. The covers install with the wire harness exiting from the bottom. 9. Obtain the correct mirror cover from the kit. Rub the liners on the three pads on the back surface of the mirror cover to activate the adhesive, then remove the liners. 10. Place the mirror cover over the back surface of the mirror and press into place for a minimum of 60 seconds. 11. Repeat Steps 8 through 10 for the remaining mirror and cover. NOTE The plastic backing plates (removed earlier) are identified with a letter “L” (left) or “R” (right) stamped on the post. The mirrors are marked with a letter “L” or “R” stamped on the swivel block. Use the correct backing plate for each mirror by matching the letters. 12. Position the mirror on the outer face of the inner fairing, with the rounded side of the mirror outboard and the Bar & Shield logo upright. a. Insert the mirror cover wiring harness through the chrome wire collar installed in Step 5. b. Insert the mirror post through the original mirror mounting hole. c. Place the correct plastic backing plate against the inner face of the inner fairing, engaging the two holes in the backing plate with the threaded stud and index pin on the mirror swivel block. d. Install the flange nut on the threaded stud and tighten to 30-40 in-lbs (3.4-4.5 Nm) . e. Repeat for the remaining mirror on the other side of the fairing

Incoming search terms:

HARLEY DAVIDSON ENGINE GUARD-MOUNTED FOG LAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
VRSC models: See Figure 3. Place the wire harness from the kit into the area in front of the battery. Do not block the air intake opening. All models except VRSC and 2004 and later XL models: See Figure 4. Install the wire harness from the kit. Place the relay in the opening of the frame under the seat area, and route the long leg of the harness forward along the frame backbone. 2004 and later XL models: See Figure 5. Remove the nuts retaining the ignition module (1) and temporarily reposition the module as shown. Place the relay in the recessed area (2) of the oil reservoir. Install the ignition module. Route the long leg of the harness along the frame backbone. CAUTION 1 WARNING -J02798 Figure 3. Install Fog Lamp Wiring Harness (VRSC Models) Place harness into this area but do not block air intake Air intake i04372 Battery Figure 4. Install Fog Lamp Wiring Harness (All Models Except VRSC. Dyna Model Shown) i02286.eps 1. Relay 2. Ground stud 3. Long leg of harness 2 1 3 2 of 6 Figure 2. Fog Lamp Wiring Harness Figure 1. Fog Lamp Schematic Ground To low beam To main circuit breaker Fuse N.O. Contact Switch Coil Fog lamp Fog lamp i01360a Relay 1. Fuse block 2. Relay 3. Connector to power 4. Ring terminals (Ground) 5. To fog lamps 6. Unterminated wire to low beam 7. Switch with boot and bracket 4 2 5 6 7 1 3 i05708 5. All 2003 and earlier models and VRSC: Cut the connector from the white power lead, and replace it with the ring terminal supplied in the kit. 6. All 2003 and earlier models, except VRSC: Connect the white wire with the ring terminal to the copper stud (BAT) terminal of the main circuit breaker. All 2004 and later models, except VRSC: Connect the white wire with connector to the B+ connector on the harness. All VRSC: Connect the white power lead to the battery positive terminal. 7. See Service Part illustration. Connect the black ground wires with the two ring terminals to the ground stud under the seat, or at any good electrical ground point. Secure the kit harness to the adjacent harnesses with cable straps (item 6) from the kit. When routing wires through the front fork, make sure the wires are clear of moving parts, to avoid pinching and possible short circuits. 8. Route the forward end of the harness past the steering head, and route the lamp switch leg of the harness along the left side of the handlebar to the clutch control. 9. See the Service Parts illustration. Obtain the switch mounting bracket (item 11) from the kit. Unscrew the boot from the lamp switch, and install the switch into the bracket. Replace the boot on the switch. NOTE If the boot becomes worn or damaged, or is lost, replace the boot to prevent moisture from entering the switch. See the Service Parts illustration (Item 12). 10. See Figure 6. Remove the lower screw (1) and washer from the clutch control clamp (3), and install the lamp switch and bracket assembly (2). Install the screw and washer and tighten to 60-80 in-lbs (7-9 Nm). 11. See the Service Parts illustration. Secure the lamp switch leg of the harness to the handlebar using the wire harness retainers already on the bike. Snap the retainers into the holes in the handlebar. 12. Remove the headlamp assembly. See HEADLAMP – REMOVAL instructions for the correct model in the Service Manual. CAUTION 3 of 6 -J02798 Figure 6. Install the Lamp Switch on the Clutch Control Clamp i04370 3 1 1. Lower clamp screw 2. Lamp switch and bracket assembly 3. Clutch control clamp 2 Figure 5. Install the Wiring Harness (2004 and Later Models) i05712 3

Incoming search terms:

ROAD TECH XM SATELLITE RADIO RECEIVER KIT INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Service Manual and follow the instructions given to remove the main fuse. Models with main CIRCUIT BREAKER: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) -J03989 1 of 8 Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Receiver Mounting Bracket Installation When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. ALL models: See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 3. Using a T-27 TORX drive head, remove the two screws that retain the clutch-lever clamp to the handlebar. 4. See Figure 4. Obtain the correct mounting bracket (2) for your vehicle, and two button-head screws (3) and spacers (4) from the kit. Insert the button-head screws into the mounting bracket, through the holes above and below the slot. Place a spacer over the threads of each screw. Insert the screw threads into the holes in the clutch lever clamp removed earlier. 5. Adjust the hand lever position for rider comfort and posture, then tighten the screws to 60-80 in-lbs (6.8-9.0 Nm) . Receiver and Antenna Bracket Installation 6. Obtain the satellite radio receiver (1), antenna bracket (6), and four lock nuts (8) from the kit. Insert the four studs on the back of the receiver through the four holes in the receiver mounting bracket. 7. See Figure 4 for mounted position of the antenna bracket to the receiver mounting bracket. Assemble a lock nut to each of the bottom two studs. Install the antenna bracket onto the top two studs, and assemble a lock nut to each top stud. Tighten the locknuts securely. Antenna Installation 8. Obtain the XM radio antenna (5) and two-sided adhesive tape (7) from the kit. 9. Use isopropyl alcohol to clean the horizontal antenna mounting surface of the antenna bracket, and the bottom (mounting) surface of the antenna. 10. Peel the liner from one side of the tape, and apply the tape squarely to the bottom surface of the antenna. 11. Peel the liner from the exposed side of the adhesive tape on the antenna base. 12. Position the antenna over the bracket without touching the adhesive to the bracket. Center the antenna over the bracket with the antenna cable toward the center of the vehicle. 13. Press the antenna squarely and firmly onto the bracket, and hold pressure for about 60 seconds. After releasing pressure, avoid direct contact with the antenna for about 20 minutes. HARNESS ROUTING AND CONNECTION NOTE Route the satellite radio receiver harness along the outside of the handlebar, even on internally-wired handlebars. 1. Route the unconnected end of the satellite radio receiver harness as follows: a. Follow the existing wiring from the left-side handlebar switches over to the center of the handlebar. Temporarily bind the harness in place as you route the harness along the handlebar to the center. Do not permanently wire tie the harness to the handlebar at this time. b. Route the wires down through the upper fork bracket (triple clamp), past the steering head, and back along the frame backbone toward the seat. Follow existing wiring where practical. For FLHT, FLHTC, FLHTCU, FLHX models , it may be necessary to remove the inner fairing cap to secure the wires. c. Locate the main harness chassis ground connection on the frame. See the Service Manual for your model and year vehicle for specific location. Remove the ground screw or nut. d. Select the appropriate ring terminal (9 or 10) to fit the ground screw or stud

Incoming search terms: