ABS Solenoid Relay Circuit TOYOTA

0

Filed Under (Toyota Manuals) by admin on 21-09-2011

Download
Start the inspection from step 1 in case of using the TOYOTA hand-held tester and start from step 2 in case
of not using the TOYOTA hand-held tester.1 Check ABS solenoid relay operation. PREPARATION: (a) Connect the TOYOTA hand-held tester to the DLC3. (b) Turn the ignition switch ON and push the TOYOTA hand-held tester main switch ON. (c) Select the ACTIVE TEST mode on the TOYOTA hand-held tester. CHECK: Check the operation sound of the ABS solenoid relay when operating it with the TOYOTA hand-held tester. OK: The operation sound of the ABS solenoid relay should be heard

Incoming search terms:

YAMAHA XVS650/ XVS650A OWNER’S MANUAL

0

Filed Under (Yamaha) by admin on 27-04-2011

download
INSTRUMENT AND CONTROL FUNCTIONS Main switch/Steering lock The main switch controls the ignition and lighting systems. Its operation is described below. EAU00036 ON Electrical circuits are switched on. The engine can be started. The key cannot be removed in this position. EAU00038 OFF All electrical circuits are switched off. The key can be removed in this position. EAU00040 LOCK The steering is locked in this position and all electrical circuits are switched off. The key can be removed in this posi- tion. To lock the steering, turn the handlebars all the way to the left. While pushing the key into the main switch, turn it from “OFF” to “LOCK” and remove it. To release the lock, turn the key to “OFF” while pushing. EW000016 WARNING Never turn the key to “OFF” or “LOCK” when the motorcycle is moving. The electrical circuits will be switched off which may result in loss of control or an accident. Be sure the motorcycle is stopped before turning the key to “OFF” or “LOCK”. 1. Push 2. Turn EAU00044 (Parking) The steering is locked in this position and the taillight comes on, but all other circuits are off. The key can be removed in this position. To use the parking position, first lock the steering, then turn the key to “ ”. Do not use this position for an extended length of time as the battery may discharge

Yamaha TW200N/ TW200NC SPECIFICATIONS AND SUPPLEMENTARY SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 26-04-2011

download
GENERAL INFORMATION MOTORCYCLE IDENTIFICATION EAS00017 VEHICLE IDENTIFICATION NUMBER The vehicle identification number 1 is stamped into the right side of the steering head pipe. EAS00018 MODEL CODE The model code label 1 is affixed to the frame. This information will be needed to order spare parts CABLE ROUTING 1 Throttle cable 2 Front brake light switch lead 3 Right handlebar switch lead 4 Clutch cable 5 Left handlebar switch lead 6 Clutch switch lead 7 Front turn signal/position light lead (left) 8 Main switch lead 9 Indicator lights lead 0  Speedometer cable A Meter light lead B Headlight coupler C Wire harness D Front turn signal/position light lead (right) E Brake hose ب Fasten the brake hose with a plastic locking tie to the brake hose grommet. ة Fasten the wire harness with a plastic locking tie PERIODIC CHECKS AND ADJUSTMENTS INTRODUCTION This chapter includes all information necessary to perform recommended checks and abjustments.If followed, these preventive maintenance procedures will ensure more reliable vehicle operation, a longer service life and reduce the need for costly overhaul work.This information applies to vehicles already in service as well as to new vehicles that are being prepared for sale.All service technicians should be familiar with this entire chapter. PERIODIC MAINTENANCE CHART FOR EMISSION CONTROL SYSTEM

Yamaha VMX12/ VMX12C Owner's Manual

0

Filed Under (Yamaha) by admin on 14-12-2010

download
Main switch EAUO0028 The main switch controls the ignition and lighting systems. The various main switch positions are described below. EAU00032 ON All electrical systems are supplied with power, the headlight, meter lighting, taillight and front position lights come on, and the engine can be started. The key cannot be removed. EAU00038 OFF All electrical systems are off. The key can be removed. 1. Push. 2. Release. 3. Turn P (Parking) The meter light, taillight and position lights are on, but all other electrical sys- tems are off. The key can be removed. The key must be pushed in from the “OFF” position to be turned to “P”. ECA00043 Do not use the parking position for an extended length of time, otherwise the battery may discharge. 1. Neutral indicator light ‘NEUTRAL’ 2. Turn signal indicator light ‘TURN’ 3. Fuel level warning light ‘FUEL’ 4. High beam indicator light ‘HIGH BEAM’ 5. Oil level warning light ‘OIL LEVEL’ EAU03034 Indicator and warning lights EAU00062 Neutral indicator light “NEUTRAL” This indicator light comes on when the transmission is in the neutral position. EAU00059 Turn signal indicator light “TURN” This indicator light flashes when the turn signal switch is pushed to the left or right. his warning light comes on when the fuel level drops below approximately 3 L (0.7 Imp gal, 0.8 US gal). When this occurs, refuel as soon as possible. The electrical circuit of the warning light can be checked according to the fol- lowing procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. Oil level warning light “OIL LEVEL” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked according to the following procedure. 1. Turn the key to “ON”. 2. If the warning light does not come on, have a Yamaha dealer check the electrical circuit. NOTE: EAU00064 High beam indicator light “HIGH BEAM” This indicator light comes on when the high beam of the headlight is switched on. Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a mal- function

Incoming search terms:

2007 Yamaha VMAX/ VMX12W1(C) OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 12-12-2010

download
GASOLINE IS HIGHLY FLAMMA- BLE: * Always turn the engine off when refueling. * Take care not to spill any gasoline on the engine or exhaust system when refueling. * Never refuel while smoking or in the vicinity of an open flame. * Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. * Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: * The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. * Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. * Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. * When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the carburetor or fuel tank. * If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes

2000 YAMAHA YZF-R1 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 27-11-2010

download
CABLE ROUTING SPEC AProperly insert the meter assembly coupler and rubber boot into the meter assembly. BRoute the meter assembly lead through the left side of the headlight housing. CThe speedometer lead with not be tighten. DInstall the headlight relays onto the headlight housing bridge. EConnect to the right front turn signal connectors. FRoute the turn signal leads upper the headlight housing boss. 1 Clutch cable 2 Left handlebar switch lead 3 Starter cable 4 Main switch lead 5 Steering cover EB206000 CABLE ROUTING -21- NRoute the thermo switch/temperature sender sub- wire harness to the outside of the radiator cap. ORoute the right handlebar switch lead behind the throttle cables. Do not cross the throttle cables and the right handlebar switch lead. PRoute the right handlebar switch lead in front of the throttle cables. GFasten the headlight lead with a plastic clamp at white tape mark. HFasten the wire harness to the headlight housing boss with a plastic locking tie. IRoute the headlight lead through the plastic guide. JRoute the throttle cable to the front side of the brake hose. KRoute the clutch cable behind the front fork leg. LMake sure that the horn leads face out. MRoute the throttle cables and right handlebar switch lead between the lower bracket and steering cover. CABLE ROUTING SPEC -22- CRoute the rollover-valve-to-fuel-tank hose to the inside of the fuel hose (California only). DRoute the coolant reservoir breather hose over the timing chain tensioner. EInsert the plastic clip through the hole in the plastic frame panel and then fasten the wire harness and coolant reservoir breather hose with it. FRoute the clutch cable between the radiator bracket and frame and in front of the thermostat assembly breather hose. GRoute the clutch cable to the inside of the radiator inlet hose. HInsert the plastic clamp into the hole in the coolant reservoir’s tab

1999 YAMAHA YZF-R6 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 25-11-2010

download
ENGINE SPECIFICATIONS/ELECTRICAL SPECIFICATIONS SPEC ENGINE SPECIFICATIONS Item Standard Limit Pistons Oil ring Dimensions (B T) End gap (installed) 1.5 2.0 mm 0.10 0.35 mm Crankshaft Crankshaft-journal-to-crankshaft- journal-bearing clearance 0.028 0.052 mm Carburetors ID mark Jet needle Pilot screw turns out 5EB1 #1, 4: N7RA #2, 3: N7SA 1-1/2 2 ELECTRICAL SPECIFICATIONS Item Standard Limit Ignition system Ignition timing 10 BTDC at 1300 r/min Ignition coils Primary coil resistance Secondary coil resistance 0.204 0.276 Ω 8.5 11.5 Ω Oil level switch model (manufacturer) 5EB (DENSO) Fuel pump relay model (manufacturer) Resistance G8R-30Y-M (OMRON) 162 198 Ω -3- TIGHTENING TORQUES SPEC CHASSIS TIGHTENING TORQUES Item Thread size Tightening torque Remarks Nm mkg Engine mounting adjusting bolts Rear shock absorber and frame Pivot shaft adjust bolt M10 7 40 5 0.7 4.0 0.5 -4- CABLE ROUTING SPEC 1 Throttle cables 2 Clutch cable 3 Left handlebar switch lead 4 Starter cable 5 Main switch lead 6 Front brake hose 7 Right handlebar switch lead AInstall the headlight relays onto the headlight housing bridge. BRoute the headlight lead through the plastic guide. CRoute the headlight lead through the headlight bracket right side, and connect relay. DDon’t kink. EPut coupler into stay. FMake sure the connector is out off the bottom end of front cowling. GRoute the right handlebar switch lead in front of the front fork inner tube. HRoute the throttle cables between the brake hose and right handlebar switch lead. IRoute the wire harness through under the left handlebar switch lead and starter cable. JFasten the left handlebar switch lead to the front fork with a plastic locking tie and cut the end of locking tie. KFasten the throttle cables and starter cable with a band. EB206000 CABLE ROUTING -5- CABLE ROUTING SPEC LLocate the end of band to for ward. Route the horn lead outside the throttle cables and fasten it to the under bracket with a plastic locking tie. Cut the end of locking tie. And then, route the horn lead under the brake hose and clamp it to the under cover

Incoming search terms:

YAMAHA YZF-R1P YZF-R1PC SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 24-11-2010

download
GASOLINE IS HIGHLY FLAMMABLE: a. Always turn the engine off when refueling. b. Take care not to spill any gasoline on the engine or exhaust system when refueling. c. Never refuel while smoking or in the vicinity of an open flame. 2. Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your motorcycle in an area that has adequate ventilation. 3. Always turn the engine off before leaving the motorcycle unattended and remove the key from the main switch. When parking the motorcycle, note the following: SAFETY INFORMATION 1 1-6 a. The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pedestrians or children are not likely to touch these hot areas. b. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over. c. Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open flame), otherwise it could catch fire. 4. When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank. 5. If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash the affected area with soap and water and change your clothes 1. Fuse box (page 6-40) 2. Front fork compression damping force adjusting screw (page 3-19) 3. Front fork rebound damping force adjusting screw (page 3-19) 4. Front fork spring preload adjusting bolt (page 3-18) 5. Front brake fluid reservoir (page 6-31) 6. Shock absorber assembly spring preload adjusting ring (page 3-20) 7. Shock absorber assembly compression damping force adjusting screw (page 3-21) 8. Owner’s tool kit (page 6-1) 9. Shock absorber assembly rebound damping force adjusting screw (page 3-21) 10. Engine oil drain bolt (page 6-14) 11. Engine oil filter cartridge

Vespa Primavera 125 Service Manual

0

Filed Under (Vespa) by admin on 28-10-2010

download
Clutch control (lever) and gear change (twist grip) – 2. Front brake lever – 3. Throttle twist grip – 4. Main switch unit – 5. Front brake shoes – 6. Rear brake pedal – 7. Kickstarter – 8. Gear selector and gear control adjusting screws – 9. Rear brake shoes – 10. Clutch – 11. Carburettor and air cleaner – 12. Choke control – 13. Fuel tap – 14. Lever securing dual seat – 15. Lever for removing engine flap. Fig. 2 – Installation of controls and transmissions PERFORMANCE AND SPECIFICATIONS Consumption (accord to CUNA Standard) 2 It/100 Km. (118 mls/U.S. gal.; 142 mls/imp. gal.), gasoline -oil mixture i. e. 2% oil. Max. speed (CUNA Standards) 85 Km/h 52.8 mph.). Carrying capacity 2 persons and 10 Kg. (22 lbs) of luggage. Range 280 Km ( 174 mls) Max fuel capacity: 5.6 It. (1.48 U.S. galls or 1.23 imp., galls ( incl. 1 It. – 0,26 U.S. galls or 0.21 imp. galls – of reserve). Wheel base 1180 mm (46″.5 ) Handlebar width 670 mm (26″.4 ) Total length 1665 mm (65″.6 ) Max height 1015 mm (40″.0 ) Min. ground clearance 225 mm ( 8″.86) Turning radius 1650 mm (64″.96) Total dry weight 73 Kg. ( 160 Ibs) ENGINE Single horizontal cylinder two stroke rotary distribution : i.e., carburated mixture is regulated by the crankshaft rotation. Displacement 121.17 cc. – 7.39 cu. in. Bore 55 mm – 2″.16. Stroke 51 mm – 2″.01. Compression ratio: 1 :8.2. Outer H. T. coil ignition. Spark advance 250 ± 1 ° before T. D. C. Sparking plug Bosch W 240 T 1 ; Champion L 86; AC 42 F; Marelli CW 240 N.
1. Steering column and front suspension – 2. Engine – 3. Crankcase clutch side with swinging arm pivoted to frame – 4. Rear suspension spring and hydraulic damper assy. – 5. Screw securing carburettor – 6. Bolt securing damper of rear suspension – 7. Bolt securing engine

Incoming search terms: