993-192 LED Light, 993-193 Marker Light CHROME RAIL BAR LIGHT INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
Read instructions thoroughly before installing. 1. Place bike on center stand. 2. Place chrome plate on to the desired position on the rail covering both the top and bottom rail with the chrome plate. 3. Insert light into the hole on the chrome plate and attached with brackets, washer and bolts provided in figure 1. Tighten securely. 4. Wire light into bike’s running or brake lights. If adding more than one light, wire lights in series.

HARLEY DAVIDSON FLSTS MUD FLAP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
Installation For installation on rear fender with marker light: 1. Cut out Rear Fender Template. 2. Use a paper punch to punch out holes marked A and C . Holes A are the locations of the marker light screws, and hole C is the location of the marker light wiring. Cut along centerline of template from top down to hole C . 3. Remove light lens by carefully pressing down on top center of light to disengage tab. 4. Remove the two screws, washers, and nuts that hold the marker light assembly in place and carefully pull the light assembly away from the fender. Disconnect the wire connector and remove the light assembly. 5. Slip template over marker light wires, align holes marked A with marker light holes, and align lower edge of template with lower edge of fender. Tape template in place. 6. Prick punch holes marked B at indicated centers on template. 7. Carefully, and as accurately as possible, drill holes marked B in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 8. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure outer holes with buttonhead screws (3), washers (6), and locknuts (7) contained in kit. The mud flap is split to fit around light assembly wires. 9. Using the longer panhead screws provided in the kit, install fender tip light and check that light is operational. For installation on rear fender without marker light: 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Rear Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes marked B and C at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked B and C in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit. For installation on front fender (FLSTS only): 1. Using a high quality masking tape, mask the lower three inches of the middle of the fender for the purpose of drawing a centerline on the fender. 2. Using a machinist’s square, locate the centerline of the fender by measuring in from each side of the fender flats. Mark the centerline on the masking tape. 3. Cut out Front Fender Template. 4. Align centerline of template with centerline drawn on fender. Align lower edge of template with lower edge of fender. Tape template in place. 5. Prick punch holes at indicated centers on template. 6. Carefully, and as accurately as possible, drill holes marked in two steps. First drill holes with a 1/16″ drill, then finish holes with a 7/32″ drill. 7. See Service Parts illustration. Place the mud flap and reinforcement inside fender and secure with buttonhead screws (3), washers (5 and 6), and locknuts (7) contained in kit

Incoming search terms: