Toyota 2006-10 Yaris L4-1.5L NTAKE TUBE, THROTTLE BODY AND ENGINE REMOVAL AND INSTALLATION

0

Filed Under (Toyota Manuals) by admin on 26-09-2011

download
turn the ignition OFF and disconnect the vehicle’s negative battery cable. NOTE: FAILURE TO FOLLOW INSTALLATION INSTRUCTIONS AND NOT USING THE PROVIDED HARDWARE MAY DAMAGE THE INTAKE TUBE, THROTTLE BODY AND ENGINE. 2. Depress the locking tab and remove the mass air sensor connector. Remove the clips that secure the mass air sensor har- ness to the stock air box. 3. Pull the vacuum switching valve and bracket assembly from the stock intake tube. Un-clip the vacuum hose from the stock intake tube. 4. Loosen the spring clamp that secures
the crank case vent tube to the stock intake tube as shown. Remove the crank case vent tube from the stock intake tube. Note: The spring clamp will be re-used. 5. Loosen the hose clamp that secures the stock intake tube to the throttle body as shown. Remove the stock intake tube from the throttle body

Toyota 2007- 2010 Camry 2009- 2010 Venza INSTALLATION INSTRUCTIONS

0

Filed Under (Toyota Manuals) by admin on 25-09-2011

download
Turn the ignition OFF and disconnect the vehi- cle’s negative battery cable Disconnect the mass sensor electrical connection by depressing the center tab and gently pulling the harness away from the mass air sensor. Release the
two wiring harness clips from the air box lid ently pull the engine cover upward to release it from the mounting grommets. Once released, Re- move engine cover from the vehicle and set aside. 4. Disconnect the vacuum line from the intake mani- fold plenum connection. 5. Disconnect the vacuum line from the upper air box lid. Toyota
2007-10 Camry 2009-10 Venza V6-3.5L 69-8611 7. Disconnect the two vacuum lines from the “Vacuum switching valve.

Incoming search terms:

BMW 3 SERIES INSTALLATION MANUAL

0

Filed Under (BMW) by admin on 17-11-2010

download
1. Turn off the ignition and disconnect the negative battery cable. NOTE: Disconnecting the negative battery cable erases pre-programmed electronic memories. Write down all memory settings before disconnecting the negative battery cable. Some radios will require an anti-theft code to be entered after the battery is reconnected. The anti-theft code is typically supplied with your owner’s manual. In the event your vehicles’ anti-theft code cannot be recovered, contact an authorized dealership to obtain your vehicles anti-theft code. TO START: 2. Depress the wire-locking clip and disconnect the mass air sensor electrical. BMW 3 SERIES (E46) 1999-00 323i, ci 1999 323iC 2001-05* 325i, ci L6-2.5L 1999-00 328i 2000 328ci 2002-05 325xi L6-2.8L NOTE: * Excluding 2003 & 2005 PZEV model with engine family 3BMXV02.5M56 & 5BMXV02.5M56 Flat Blade Screwdriver Ratchet Extension 10mm Socket 10mm Wrench 4mm Allen A intake tube (EL) 1 087139 B hose ; 4mm id x 2″ l 1 08062 C npt fi tting; 1/4″ x 5/16″ barb 1 08908 D hose clamp #48 3 08601 E silicone hose 3.25″id x 2″l 1 08690 F nut; 6mm nylock 7 07553 G washer; 1/4″id x 5/8″od fl at 7 08275 H washer; 1/4″ split lock 1 08198 I bolt; 6mm-1.00 x 16mm, b/h/a 2 07730 J bolt; 6mm-1.00 x 12mm, b/h/a 4 07794 K washer; 1/4″id x 1″od fender 2 08160 L bracket 1 010087 M heat shield “A” 1 07492 N heat shield “C” 1 07497 O heat shield “B” 1 07494 P edge trim 46″L 1 102487 Q air fi lter 1 RU-4730 3. Pull up on the four fresh air duct-retaining pins to release them from the radiator core support. 4. Lift up and remove the fresh air duct from the vehicle as shown. NOTE: Disconnect the fresh air tube from the fresh air duct. 5. Loosen the hose clamp which secures the intake tube to the mass air sensor, and then disconnect the intake tube from the mass air sensor as shown. 6. Remove the two-factory air box mounting bolts shown.