HARLEY DAVIDSON XL HAND LEVER INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
These kits fit all 2004 and later XL Sportster® model motorcy- BRAKE LEVER INSTALLATION Removing the Brake Lever Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) is 01010 Figure 1. 5/32 in. (4 mm) Cardboard Insert 1. See Figure 1. Squeeze the brake lever and place the cardboard insert between the brake lever and lever bracket. NOTE Use the eyelet of an ordinary cable strap if the cardboard insert is not available. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 2. See Figure 2. Remove retaining ring from pivot pin groove at bottom of master cylinder bracket. Save the pivot pin for re-use, discard the retaining ring. 3. Remove pivot pin and brake hand lever from master cylinder assembly. NOTE Do not remove the handlebar clamp or switch housing assembly to remove the brake lever. Installing the Brake Lever NOTE Follow the instructions in Steps 4 and 5 carefully in order to prevent the actuating tab on the brake lever from damaging the rubber boot and plunger of the front stoplight switch

HARLEY DAVIDSON CHROME REAR MASTER CYLINDER COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
1. Clean rear master cylinder cover, then remove two screws that hold cover in place. 2. Remove original cover (with sight glass) and gasket. 3. Put new cover and gasket in position. 4. Install cover screws and tighten screws (1) to 6-8 in-lbs (.7-.9 Nm). Direct contact of D.O.T. 4 brake fluid with eyes can cause irritation. Avoid eye contact. In case of eye contact flush with large amounts of water and get medical attention. Swallowing large amounts of D.O.T. 4 brake fluid can cause digestive discomfort. If swallowed, obtain medical attention. Use in well ventilated area. KEEP OUT OF REACH OF CHILDREN. (00240a

2008 Kawasaki ZG1400 Concours ABS Front 3-Line Kit and FK003D625R Single Line Rear INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our front brake line kit: You should have three (3) hoses, one (1) double banjo bolt, and two (2) single banjo bolts There are also a total of nine (9) washers and (3) brass conic inversors. Seven (7) washers and two (2) inversors will be used; the rest are spares. If you have purchased a rear kit as well, locate the following additional pieces: One (1) hose with bracket and c-clip attached, one (1) single banjo bolt, two (2) brass inversors and three (3) washers. You will use one (1) “olive” conic inversor and two (2) washers, the rest are spares. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. On the front brake line kit, we are replacing three hoses and their respective blocks (see pictures 1-2 for blocks) . For the rear, we are replacing one hose from the master cylinder to the ABS hard line. Take note of how the stock system was routed, in case you need to reinstall it. Step 4: Locate Line A – This will travel from the master cylinder to the ABS Junction. (See picture 3) You will use a single banjo bolt and two washers at the master cylinder, and an “olive” inversor to thread female end to hard pipe for incoming ABS (right side). * We have replaced the block at the upper triple clamp with a c-clip; please use your stock bolt to thread this in. (See picture 4) Locate Line B – This will travel from the ABS Junction to the right caliper. First, thread the female end to the hard pipe for outgoing ABS (left side). There will be a bolt from the OEM blocks at ABS Junction; please use this to thread c-clips into frame as shown in picture 5 . There is another bolt/OEM block located at the lower triple clamp; please use this to thread the c-clip in as seen in picture 6. Locate Line C – This will cross over the front fender using OEM holders, from right caliper to left caliper. Thread caliper banjos from Line B and C using the following sequence: double banjo hex, washer, 40- degree banjo from Line C, washer, 20-degree banjo from Line B, washer, caliper. Please see pictures 7 and 8 for reference. Thread single banjo bolt into left caliper, using two washers and 40-degree banjo. If applicable, locate rear Line D – this will travel from the rear master cylinder to the hard line for ABS. Thread the hard pipe into female end using a “olive” inversor, and attach bracket to swingarm as seen in picture 9 . Use the bolt from the holder for ABS hose, and sit our bracket on top of the OEM holder. Using the bolt from the OEM ABS hose holder in location shown in picture 10 , attach the c-clip on top of holder and tighten. Finally, thread 30-degree banjo in caliper using the following sequence: single banjo hex, washer, banjo, washer, caliper

2008 Suzuki GSXR 600-750 Super bike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our SUPERBIKE brake line kit: You should have two (2) hoses, one (1) double banjo bolt, and two (2) male adapters with two 1.55mm thick washers. There are also a total of (7) washers. five (5) will be used, and two (2) are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter with the two thick crush washers provided into the calipers with one washer, and torque at 12 to 13 ft pounds. Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 90 degree banjo from left line, washer, 90 banjo from right line, washer and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (For positioning see picture A) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see picture B) . Thread each female end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using (GALFER’S C-CLIP) to bring the lines together about the same level as the lower triple clamp.

2004-2007 HONDA CBR 1000RR Super bike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Make sure to save the nut and bolt that are currently holding the stock lower section of the hoses. (See picture A) Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 40-degree banjo from right line, washer, 40-degree banjo from left line, washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (For positioning see picture B) . Make sure that the 90-degree fittings on each caliper are pointing straight up (see picture C) . Thread each banjo end onto the adapter, and torque to 6 ½ Ft pounds. Please tighten the “C” clips on the fender using the OEM bolts we asked you to save above. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, using the galfer 2line clip to bring the lines together and mounting it to the triple tree will insure proper clearness and routing. (See picture D) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with Galfer DOT 4- brake fluid is recommended.

Incoming search terms:

2006-2008 Yamaha R6 FK002D512GP ( GP Kit ) INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
Step 1: Identify the key components that complete our GP kit: You should have 3-line (front kit), 3 SINGLE banjo bolt and 1 C-CLIP. There are also a total of 8 washers. 6 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines, all other installations VOID warranty. Inspect your brake system after every race. Step 2: Cover the complete front end of the bike so that if any brake fluid does spill the paint will not be damaged, brake fluid will spill, there is no question!! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the GALFER GP 3-Line starting with the master cylinder line (top line). Torque level is 12 to 13 ft pounds. (See picture A2) Step 5: Install the C-CLIP provided to the lower triple tee top line needs to be held by c-clip [see picture A4&A5] . Lower lines will travel in front of the forks to the calipers; two single banjo bolt (see picture A1) are included for master cylinder to each caliper. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, forty-degree banjo (Top line), and washer. Single banjo bolt torque level is 12 FT Pounds. ( See picture A2 for positioning) Make sure that the [ CALIPER fittings ] on each caliper are positioned [ positioning ] (see picture A6- A7) . Thread banjo bolt into the caliper, and torque bolt to 12 to 13 Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and are clear of any obstructions. Once the lines have been checked for clearance. Proceed to step #6 Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with GALFER DOT 4-brake fluid is recommended.

2007 Yamaha R1 Front Brake Line Kit Installation instructions

0

Filed Under (Yamaha) by admin on 27-01-2011

download
To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process can be messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, 40-degree banjo labeled for right line, washer, 20-degree banjo labeled for left line, washer, master cylinder. Double banjo bolts must be torqued at 12 FT pounds. (See picture A for sequence) Step 5: Route brake lines below the stock lower triple clamp, and zip tie them together. This will ensure your lines stay in position as the steering moves. Also, make sure the lines are secured beneath the steering stabilizer rod. (See picture C) Step 6: Before installing the lines onto the right and left calipers, replace the OEM bracket with the enclosed “C-clip”. Route the hose through the new bracket and thread the single banjo bolts at each caliper using the following sequence: 20-degree banjo, washer, single banjo bolt, washer, thread into caliper. Torque banjo bolts to 12 FT pounds. (See picture B) Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Step 7: Bleed brake system according to owner’s manual, and build appropriate pressure. Keep in mind your master cylinder is equipped with it’s own bleeder nipple. Finish with Galfer DOT-4 brake fluid

2003-2004 Honda CBR600RR FK003D348SB Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 25-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S1) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S2) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, 12-degree banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. (See picture S3) Make sure that the 40-degree fittings on each caliper are pointing away from the bike just a little bit (see picture S4/S5 for right caliper and S6/S7 for left) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area

HONDA VTX1800 Complete System Installation Instructions

0

Filed Under (Uncategorized) by admin on 12-01-2011

download
You should have 2 sets on instructions, use the 2 !! -This kit includes 8 brake lines and 1 clutch hose. -1) First of all, remove gas tank and seat. -2) Remove all fluid from motorcycle, bike has 5 bleeding nipples. -3) Understand the complete stock brake system write yourself a few notes about the connections for the front caliper lines, make sure to label all lines as you remove them in case you need to re-install. -4) Set up one of the “T” block on the frame by the gas tank. -5) Remove rear stock line and stock junction block (under seat area) -6) install Galfer rear hose, (Diagram 1 ) and route it as shown in picture, use stock frame clamps to bring rear hose to the Galfer “T”. (See picture on step 4) 7) Remove stock foot brake line. Route line labeled as Diagram #2 from foot master cylinder to 3-way splitter on frame. Foot master cylinder end banjo:

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms: