Camry, Camry HV 2007 – 2009 Sunvisor – Removal & Installation Procedures

0

Filed Under (Toyota Manuals) by admin on 27-05-2011

Download

Partially install the bracket cover into the sunvisor bracket making sure both temporary set claws are
engaged as shown in Figure 5. NOTE
Make sure to ONLY partially install the bracket cover into the bracket during installation,
because damage to the clip, sunvisor mount or roof sheet metal tabs may occur if the bracket
cover is fully in the sunvisor bracket.
2. Install the sunvisor assembly into the opening in the sheet metal roof panel by grasping the
sunvisor assembly with two hands and pushing the bracket upward as shown in Figure 6.

Incoming search terms:

HARLEY DAVIDSON XL 2-UP CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
Additional Parts Required •XL883 and XL883L models require the separate purchase of Passenger Footpeg Kit 50203-04, which is available from a Harley-Davidson dealer. •XL1200N, XL883N and XL1200X models require separate purchase of guide washer 7487. Kit Contents See Table 1 and Table 2 for the kit number and corresponding grabstrap number. See Figure 7 and Table 3 for a list of the service parts. Table 1. Kit Contents Grabstrap Kit Number Grabstrap Kit Number 51312-07 52883-04A 51295-04 51686-05 51312-07 52907-04A 51295-04 52283-06 51312-07 52923-04B 51295-04 52299-06 51312-07 52859-04B Table 2. Kit Contents Grabstrap Kit Number Grabstrap Kit Number 51312-07 52849-04B 51295-04 51386-04 51312-07 52871-04A 51295-04 51684-05 51312-07 52884-04A 51295-04 51685-05 51312-07 52916-04B 51295-04 52176-06 51295-04 52184-06 INSTALLATION NOTE When installing this kit, be careful not to scratch painted surfaces (fender, tank, etc.) with the metal tabs on the seat. Models Originally Equipped With Solo Seat 1. Remove the seat according to the instructions in the owner’s manual. 2. See Figure 1. Remove and discard seat post washer (2) and screw (3) from the front fender hole. 3. For XL883 and XL883L models: See Figure 2. Remove plastic cap (1) from rearward fender hole and save. 4. Remove retention nut (2) and washer (3) from middle fender hole

Incoming search terms:

HARLEY DAVIDSON DYNA SEAT WITH ADJUSTABLE RIDER BACKREST INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION Seat Installation NOTE When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with the metal tabs on the seat. 1. Remove the existing seat and passenger grab strap following the instructions in the appropriate Service Manual. Discard the grab strap and retain all other hardware for later use. 2. See Figure 9. Remove the seat bracket from the stock seat. 3. For all except FXDWG: Install the stock seat bracket onto the new seat with the stock screws. For FXDWG: Install new seat bracket 52152-97 onto the new seat with the stock screws. For models equipped with original or accessory two- up seating: Proceed to Step 6. 4. On models equipped with an accessory Solo Seat: Remove the plastic plug from the hole in the rear fender where the rear seat bracket will be attached. 5. See Figure 9. Slide the retention nut (9) onto the cable strap (11) so the wide end of the nut rests on the eye of the strap. Thread the cable strap up under the fender and through the fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. Seat the rib of the retention nut in the notch in the fender hole and slide the retention washer (10) into place from the rear. This will lock the retention nut in place. 6. See Figure 1. Place the black bracket (1) from the kit onto the frame as shown. 7. See Figure 9. Install the new grab strap (8) in the original location with the hardware saved in Step 1. Tighten the nut to 96 in-lbs (10.85 Nm) . 8. See Figure 1. Install the screw (2) in the hole on the forward edge of the bracket. Attach the locknut (3) and washer (4) from under the frame. Tighten to 96 in-lbs (10.85 Nm)

HARLEY DAVIDSON DYNA GLIDE CUSTOM SEAT KIT Installation Instructions

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
Installation When performing the following procedures, be careful not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat from motorcycle. Keep lockwasher and screw. 2. Remove existing grab strap and all attaching hardware. 3. Install new grab strap onto motorcycle at same location old grab strap was removed (re-use existing hardware). 4. On all models, except FXDWG , install existing stock rear bracket onto seat using stock hardware. On FXDWG models, install the new rear bracket, 52152- 97 onto the seat using the stock hardware. 5. Position new seat on motorcycle. Be sure bracket on front of seat fully engages seat mounting tab on frame. NOTE On rear fenders of 1997 -2003 models, a captive nut secured with a plastic retention washer has replaced the previously used weld nut. Do not remove the plastic retention washer unless the captive nut is damaged and must be replaced. The plastic retention washer also prevents seat bracket from contacting paint on fender. Therefore, no nylon washer is required between bracket and fender on 1997 – 2003 models. 1996 DYNA MODELS ONLY Secure seat with stock screw, stock lockwasher and place stock nylon washer between seat bracket and fender. 1997 – 2003 DYNA MODELS Secure seat with stock screw and stock lockwasher.

HARLEY DAVIDSON FXR BADLANDER CUSTOM SEAT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
This kit is designed for installation on 1982 and later FXR model vehicles.installation 1 CAUTION When performing the following procedures, be cautious not to scratch painted surfaces (fender, tank, etc.) with metal tabs on seat. 1. Remove existing seat from motorcycle. Discard rear mounting hardware (screw, lockwasher and nylon washer). 2. Remove grab strap from vehicle and discard. 3. Locate seat bracket from kit. Remove two mounting screws securing rear portion of tank to motorcycle frame. Discard screw, but save washers. 4. Install seat bracket from kit onto motorcycle at tank mounting tab location, using two hex cap screws from kit and washers removed in Step 3. 5. See Figure 1. Locate grab strap (1) from kit. Bring the two ends of grab strap (1) around the top and outside of frame (2) so that end of grab strap can be joined under seat. 6. See Figure 1. Line up two holes on one end of grab strap with two hole in opposite end of grab strap. Place one metal washer (3) from kit over end of flange screw (4) from kit. Insert screw (4) through one set of holes in grab strap (1). Place one remaining metal washer (3) over end of flange screw (4). Tighten assembly together using locknut (5) from kit. 7. Locate battery mounting tab (6) on motorcycle. Loosen locknut (7) and back out hex head screw (8) from frame until remaining joined holes in grab strap (1) can be slipped into position over end of screw (8). Re-tighten screw (8) and locknut (7). 8. Carefully slip seat into position (without scratching tank or fender) under grab strap and engage mounting tab on front of seat with mounting bracket installed at tank mounting tab. 9. Secure rear of seat using truss head screw with lockwasher and guide washer (placed between seat bracket and fender) from kit. The guide washer will center the screw in the seat bracket hole and serve as a washer to protect the fender

Incoming search terms:

Incoming search terms: