KAWASAKI TERYX EFI Installation And Removal Instructions

0

Filed Under (Kawasaki) by admin on 06-05-2012

download
1. The Stage IV controller can be mounted in numerous places. Placement depends on personal preferences. Only mount in locations where no damage may occur from sharp or hot objects. 4. Start the UTV and in approximately four seconds the lights on the Stage IV controller will be visible. With a proper install, you should see lights going from side to side on the controller. This will last approximately eight seconds and then will stop. After lights have stopped going side to side, you will notice a great light on the left side of the controller. When you rev the motor, lights will increase across the controller and even change colors. 5. Double check all fasteners and connections. 7. The Stage IV controller has been programmed for ultimate performance when using Trinity Racing’s Stage IV exhaust system and Powerflow intake system on an otherwise stock engine. Different products, modifications, or other conditions may require additional adjustments. Please refer to Basic Tuning Adjustments and all final fuel adjustments are the customer’s responsibility. 8. You are now ready to ride! Enjoy your new Stage IV fuel management controller! Basic Tuning Adjustments 1. The following instructions are for basic fuel tuning. Modes 1,2, & 3 are allowing adjustments to increase and decrease the amount of fuel the engine needs. Modes 4 & 5 are for advanced tuning only. DO NOT change modes 4 & 5 when doing basic tuning! 2. To help understand how these modes work, you can think of them as if you were working with a carburetor. 3. Remember each time you push the MODE button you will be advancing to the next mode. Push the MODE button once and you are now in mode 1, push the MODE button again and you are now in mode 2 and so on. You only need to be concerned with modes 1, 2 & 3 for basic tuning. Modes 4 & 5 are for advanced tuning ONLY. 4. If you need to go back to the settings that were pre programmed when you purchased the controller, just look at the picture in each mode, the colored square represents where the settings were when you purchased the controller. 5. Looking at the controller you will see eight lights with numbers under them, this is what you need to look at when changing settings. The #1 light on the controller represents the leanest setting

Harley Davidson Steering Wheel Radio Control Interface Installation instructions

0

Filed Under (Harley Davidson) by admin on 03-05-2012

download
1) Turn on the ignition to supply power to the SWI-3. 2) Use a pen to depress the “program mode” button. Remove pen when left LED light comes on. 3) Within 10 seconds press and hold one of the steering wheel function buttons. Continue to hold steering wheel button until the left LED turns off. Release the steering wheel button and the right LED turns on. 4) Place the stereo’s IR remote within 3″ of the “IR Input” port on the side of the SWI-3 next to the program button. Press and hold the remote’s button that corresponds to the steering wheel button that was pressed. Continue to hold the remote’s button until the right LED turns off. Release the button and the left LED will turn on. 5) Repeat steps 3 and 4 until all radio steering wheel functions are programmed. 6) When programming is complete, wait 10 seconds and both LED’s will flash 3 times. This indicates an automatic program exit. Do not stop more than 10 seconds while programming or there will be an automatic program exit and you will have to start over at step number 2 above. Turning off ignition before the automatic exit will require starting over at step 2 above. The SWI-3 can be reprogrammed unlimited times. Testing • Test the SWI-3 by holding it’s infrared LED (LED on the end of 4′ lead) close to the stereo and verify that it works properly. Experiment with various locations for the LED. You should be able to find a hidden and convenient mounting location. Try along the top front and /or bottom of the stereo as well as it’s sides. The LED can be replaced with most any IR LED, like Radio Shack’s # 276-143. The longest lead of the LED connects to the red wire of the 4′ cable and the short lead of the LED connects to the black wire of the 4′ cable

ACE -325X/ 395 X-XX CLOCK, UNIT, WHEEL, ODOMETER, TEMPERATURE & FUEL METER SETTING

0

Filed Under (Honda) by admin on 24-12-2011

download
Setup operations include 12/24hour clock, bar tachometer scale, shift warning RPM, numbers of engine rotation per signal, wheel circumference, units, odometer adjustment, units of temperature, temperature warning and fuel meter input resistance selection. These must be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen. 2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at any setting screen to finish the setting and go to main screen. 3. It displays “12 or 24H and XX:XX-XX” symbols and AM/PM in case you select 12H. Operates buttons as descriptions of item 2 to finish clock and jump to 8,000/16,000rpm scale setting. 4. It displays 8,000rpm scale, presess RESET button to convert 8,000 or 16,000rpm. Press MODE button to confirm the setting and jump to shift RPM warning setting. 5. It displays ” RPM rXXX00 “. Follow the item 2 of button operation to finish the shift RPM warning setting and jump to engine specification setting. 6. It displays “SPC-X.X RPM”, the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal. 7. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to wheel circumference setting screen. 8. In “cXXXX” display, “c” means “Circumference”, following 4 default digits; flashing digit is digit to be set. Follow the item 2 of button operation to finish the wheel circumference setting and jump to unit setting. 9. It displays KM/h or MPH, each press of RESET button converts unit; press MODE button to confirm unit setting and jump to odometer setting. 10. It displays “ODO & 00000Xkm”, the “X” is tested odometer in factory, follow item 2 to setting a desired odometer and jump to thermometer unit setting. The setting screen will disappear when the odometer is over 30km or your setting is over 30km and returned to main screen. 11. It displaysm ” , or oFF”, each press of RESET button converts , or oFF; press MODE button to confirm temperature setting and jump to temperature warning setting. 12. It displays ” XXX” and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to fuel sensor input resistance setting. 13. It displays “100r and fuel tank symbol”, follow the item 2 to select 100, 250, 510 Ohm or oFF and return to the main screen. The fuel meter bar will disappear if you select oFF mode.

Incoming search terms:

KAWASAKI TERYX EFI Installation Instructions.

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
Basic Tuning Adjustments 1. The following instructions are for basic fuel tuning. Modes 1,2, & 3 are allowing adjustments to increase and decrease the amount of fuel the engine needs. Modes 4 & 5 are for advanced tuning only. DO NOT change modes 4 & 5 when doing basic tuning! 2. To help understand how these modes work, you can think of them as if you were working with a carburetor. 3. Remember each time you push the MODE button you will be advancing to the next mode. Push the MODE button once and you are now in mode 1, push the MODE button again and you are now in mode 2 and so on. You only need to be concerned with modes 1, 2 & 3 for basic tuning. Modes 4 & 5 are for advanced tuning ONLY. 4. If you need to go back to the settings that were pre programmed when you purchased the controller, just look at the picture in each mode, the colored square represents where the settings were when you purchased the controller. 5. Looking at the controller you will see eight lights with numbers under them, this is what you need to look at when changing settings. The #1 light on the controller represents the leanest setting. TRINITY RACING DOES NOT TAKE REPONSIBLITY FOR DAMAGES THAT MAY OCCUR DURING OPERATION OF YOUR VEHICLE UNDER IMPROPER JET SETTINGS. IT IS THE FINAL RESPONSIBLITY OF THE OWNER/RIDER TO ADJUST JETTING TO SPECIFIC RIDING CONDITIONS AND ELEVATION BEFORE RIDING. WARNING! 1.877.FAS TOYS 2.Remove both seats 6. Re-install engine cover and seats. 6. Mode 1 green light represents idle & cruise adjustment (i.e. pilot jet). To adjust this setting push the MODE button once and then push the plus or minus buttons to adjust fuel as needed. 7. Mode 2 yellow light represents an additional amount of fuel added during acceleration (i.e. needle position). To adjust this setting, push MODE twice and then push the plus or minus buttons to adjust fuel as needed. 12 34 56 7 8 12 34 56 7 8 8. Mode 3 red light represents more fuel being added during full throttle (i.e. main jet). To adjust this setting push the MODE button three times and then push the plus or minus buttons to adjust fuel as needed. 9. If you are confident about your tuning skills and feel you need to adjust other parameters, see Advanced Tuning. 12 34 56 7 8 Advanced Tuning Adjustments 1. Advance tuning has two modes in which to adjust. They are called mode 4 and mode 5. In basic tuning, you are changing the amount of fuel that the engine receives, but with advance tuning, you will be changing when the fuel will be available. In each mode you can adjust how soon the fuel delivery occurs. 2. Mode 4 yellow light and blue light represent when the fuel delivery is available during partial throttle acceleration. To adjust this setting, push the MODE button four times and then push the plus or minus buttons to adjust fuel as needed. Only the yellow light will be changing.

Incoming search terms:

2004-UP DIGITAL SPEEDOMETER MODULE Owner's Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
SPEEDOMETER INSTALLATION The following procedure details the removal of the factory speedometer and installation of the digital speedometer on Softail models; however the process is similar for all other models: 1. Remove the nut and washer (item #4 in the accompanying exploded view) that secures the console (#5) to the fuel tank. 2. Lay a clean shop rag on the fuel tank and flip the console over to expose the underside of the console. 3. Separate the 12-pin harness connector (#2) from the speedometer. 4. Unscrew the rubber cover from the “trip” reset switch (#6) on t left side of the console. he 5. Remove the “trip” switch from the console. 6. Pry between the three tabs that hold the back clamp (#7) to the speedometer (#1). Remove the back clamp from the speedometer. 7. Remove the speedometer from the console. 8. Remove the gasket (#3) from the speedometer. 9. Installation is the reverse of removal. CHAPTER 3 SPEEDOMETER OPERATION When the motorcycle key switch is ON, the speedometer will enter “normal” mode. Pressing the MODE button will cycle through the following display options: Odometer (ODOM) displays the mileage since the speedometer was installed. Trip (TRIP) displays the mileage since the last time the “trip” button was pressed. Head Temp (H TEMP) displays the cylinder head temperature in degrees F. Battery V (BATT V) displays the battery voltage Fuel (FUEL) displays the fuel level in gallons. Miles Per Gallon (MPG) displays the fuel economy in miles per gallon. Range (RANGE) displays the calculated range (in miles) until the tank reaches its empty value. Horsepower (POWER) to perform the horsepower test, follow these steps

Edelbrock Nitrous Systems Digital RPM Window Switch USER MANUAL

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Programming the RPM The engine application and rpm activation points are easily selected through push buttons on the LED panel. This Switch can be programmed for a variety of engine and ignitions as shown below. 1-Cylinder This program is used for individual coil per cylinder systems (such as GM LS-1 engines, or ’99-Up Mustangs) 2-Cylinder This is for ignitions with coil packs that fire two cylinders at the same time (waste spark systems) 2-Cyl. Odd Use on coil pack ignitions that are on odd-fire engines such as a Viper V-10 or Harley-Davidson motorcycle. 4-Cylinder Typical 4-cylinder engines with a distributor. 6-Cylinder Typical 6-cylinder engines with a distributor. 6-Cyl. Odd Typical 6-cylinder odd-fire engines with a distributor. 8-Cylinder Typical 8-cylinder engines with a distributor. 1.2 Push Button LED Panel The rpm activation points and cylinder select are programmed through the push buttons on the LED panel (Figure 1) . Press the Mode button, and notice that the indicator point above the On RPM lights. When that point is on, you can scroll the rpm value up or down with the arrows on the left of the panel. Once your On rpm is set, push the Mode button until the Off RPM point lights, then set the off rpm point. Note that if the rpm point is not changed within 2-seconds, the screen returns to the current rpm reading (zero when the engine is not running). After setting the On and Off points, press the Mode button to program the Cylinder Select Valve (default is for 8-cyl.

Incoming search terms:

FC designed and built solely for Victory Motorcycles Installation

0

Filed Under (Victory) by admin on 31-10-2010

download
1. Remove gas tank as per service manual procedure 2. Disconnect negative lead from battery 3. Determine a location for the VFC III unit. Suggested locations are as follows: on left or right side under the covers, on top or side of battery, on inside of the side covers, on PCM or under seat 4. Locate rear injector, disconnect factory connection using care not to break it, the red tab must be lifted first and then push the release to remove plug. Plug it into the female end of the VFC, Then plug the male end of the VFC into the injector. 5. Locate connection of front jumper harness- it is located on the right side of frame – in the center of air box. Disconnect and plug appropriate VFC connectors in place. 6. Zip tie harness so that it is free from being contacted 7. Install gas tank and connect ground terminal of VFC along with the factory ground lead. Note, On Vegas, Kingpin, Jackpot & Hammer Models. Be sure not to pinch VFC harness under rear tank mounting bracket, the harness must run on the side of or under the frame in this area as not to contact the rear tank mount. 8. Turn the motorcycle key to the “ON” position, after fuel pump cycles the Green / Red lights will flash and will remain flashing until an injector signal is detected, this occurs when the M/C is started. Once running the green will scroll for 4 seconds and then turn solid until another circuit is activated. Some 2000-20001 bikes will not light the box until started. The module controls your basic fuel adjustments and your fuel delivery for the Nitrous when activated. The following functions and colors that represent them are as follows. Basic Module description and adjustments ; the module has 3 button adjustments, Center is the mode selector, this scrolls through and chooses the feature that you want to adjust. To the left of it is the button in which minus’s in value the selected feature. To the right of the mode button is the plus button which makes the feature selected go higher in value. If a fuel feature is selected the minus button will diminish fuel down to the lowest level of the current download and plus will add fuel up to the maximum amount calibrated into the module. There are 8 LED lights on the front panel with 15 points of adjustment ranging from 0 to 8 in increments of .5 or 1/2 . Ex. 1 – 1.5 – 2 – 2.5 – 3 – 3.5 – 4 – 4.5 – 5 – 5.5 – 6 – 6.5 – 7 – 7.5 – 8