ROKON Illustrated Owners and Parts Manual

0

Filed Under (Rokon) by admin on 28-11-2010

download
Front and Rear Brake. Check brake action. Check pucks to see that they are not over worn. There should be visible brake material on both sides of the brake disc. See Section 6. Fuel Tank. Check fuel level. Fill as necessary. Use super unleaded for altitudes above 10,000 ft. Engine Oil. The engine holds .6 qt. of SAE10W30/40 motor oil. Fill to the dipstick “full” line. Miter Box and Transmission. They are fi lled at the factory and need not be checked at the start. The miter box should have 2.5 oz. of EP 80W90 gear lube oil. The transmission takes 6 oz. of EP 80W90 gear lube oil. The transmission has a fi ll to plug near the bottom of the transmission( shown on page 46). There is no fi ll level for the miter box. Over fi lling of either the miter box or transmission will result in leakage. Throttle. Check for proper throttle cable operation. Look for smooth response to twist action. Wheels and Tires. Check Tire pressure, wear and damage. Fittings and Fasteners. Check all fi ttings and fasteners. Drive Chains. Check chains for tension and lubrication. Adjust tension for 1/2″ – 3/4″ defl ection at mid point. Engine Manual. Read your engine manual completely and follow all instructions

1985 Yamaha SRX250 REPAIR MANUAL

0

Filed Under (Yamaha) by admin on 21-11-2010

download
FILTER/FRONT AND REAR BRAKE AIR FILTER 1. Remove: °Right side cover ‘Air filter case cover ‘Air filter guide ’Air filter element ® op The engine should never be run without the air/filter element installed; excessive piston and/or cylinder wear may result. 2. lnspect: ‘Element Contamination->Clean element with solvent NOTE: A. o . After leaning, remove the remaining solvent by squeezing the element. 3. Apply: ‘SAE i0/V30 motor oil (to the elementi NOTE: . or o . .. Sqeeze out the excess oil. Element should be wet but not dripping. FRONT AND REAR BRAKE Front Brake Lever Free Play Adjustment Proper lever free play is essential to avoid ex- cessive brake drag

Rokon Illustrated Repair Procedures and Parts Manual

0

Filed Under (Rokon) by admin on 20-11-2010

download
Front and Rear Brake. Check brake action. Check pucks to see that they are not over worn. There should be visible brake material on both sides of the brake disc. See Section 6. Fuel Tank. Check fuel level. Fill as necessary. Use super unleaded for altitudes above 10,000 ft. Engine Oil. The engine holds .6 qt. of SAE10W30/40 motor oil. Fill to the dipstick “full” line. Miter Box and Transmission. They are filled at the factory and need not be checked at the start. The miter box should have 2.5 oz. of EP 80W90 gear lube oil. The transmission takes 6 oz. of EP 80W90 gear lube oil. The transmission has a fill to plug near the bottom of the transmission( shown on page 46). There is no fill level for the miter box. Over filling of either the miter box or transmission will result in leakage. Throttle. Check for proper throttle cable operation. Look for smooth response to twist action. Wheels and Tires. Check Tire pressure, wear and damage. Fittings and Fasteners. Check all fittings and fasteners. Drive Chains. Check chains for tension and lubrication. Adjust tension for 1/2″ – 3/4″ deflection at mid point. Engine Manual. Read your engine manual completely and follow all instructions Periodic Maintenance and Adjustment 1. Inspect all fasteners for tightness. 2. The drive chains require adjustment at intervals, depending on the mileage and the care which the operator has given the chains. Initial wear must be taken up by adjustment after the first few hours of use. Total deflection should be 1/2″ to 3/4″ when measured midway between the two sprockets of the most loose position. To adjust the chains, loosen the axle bolts and the adjusting bolt lock nuts, and turn the adjusting bolts equally in or out as required to give the chain the proper setting. After adjusting the chain, rotate the wheel and check to make sure the chain is aligned properly. Periodically, the chains should be removed from the machine and cleaned in solvent and re-lubricated. They should be lubricated with one of the chain lubricants on the market which can be applied to the chain in a liquid form and will penetrate to the inner parts of the rollers. 3. Clean the air filter based on use. See Engine Manual. 4. Use normal repair procedures for tires and tubes. Re-seat the tire beads with 40 PSI , then deflate to the 3 -5 PSI operating pressure.

Incoming search terms:

KTM 250/300/380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 19-11-2010

download
Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. Checking the setting of the TVC system The function of the TVC system is checked with the engine running. This test checks the start of advance and the end of advance. -For this, remove the left control cover. -Connect a rev counter (either to the ignition cable or to the blue/white cable in the electronics box, depending on the rev counter design). -Start engine, accelerate gently and observe when the TVC system starts to advance (tooth segment creeps upwards) Bleeding of the hydraulic clutch -Take off cover together with rubber bellows. -At the slave cylinder of the clutch, remove the bleeder nipple 2 . It its place, mount the bleeder syringe 3 which is filled with SAE 10 hydraulic oil