1994-1998 HONDA RVF400RR Racing Kit INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
(1)Fuel High Octane white gasoline (2)Engine Oil Recommended Oil: HONDA Ultra-GP (for four-cycle Motorbike) SAE20W-50 or 10W-40
Full Capacity: 3.0Liter (5.28pt) Oil Exchange: 2.5Liter (4.4pt) Filter Exchange: 2.4Liter (4.224pt) (3)Spark Plug NGK R 847-10(11)(4)Cooling Water Highly recommend checking the water level on each ignition/riding. Ingredient: Tapped water or Drinking water I. Unscrew a radiator cap. Apply water up to limb of intake. II. Hold steering and heave the body two or three times to let air out. III.Add water if necessary. IV. Screw the cap tighten.V. Start Engine then check water level again. Add water if necessary. < Notes for racing condition> • Keep your attention when you re-check the water level since the water would spill out of intake. Also cover the body with wastes. • Drain cooling water in a catch-tank before riding. • Drain whole water in a radiator after riding. It avoids corrosion or clog of components. • It is admitted adding coolant in winter season. Handle carefully when you apply them. It makes the circuit slippery if it drops or spilled.

Installation manual for fork springs

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
1.) Motorcycle is securely jacked up on an assembly stand Jack up the bike at the front axis so that the fork is completely extended, not loaded and free to be moved. You might also hang up your bike using a cable or a hydraulic jack. 2. ) It is advisable to dismount the forks’ inner tubes because otherwise oil rests might remain in the lower part of the fork and the cartridge systems oil cannot be exchanged during drain off. Even degassing the fork is going to be much simpler this way. .) Take off brake callipers, front wheel and front fender Tip: 1. Check the owner’s repair manual of your motorbike for disassembly instruction. 2. Do not let the brake callipers dangle on the lines; rather fasten them with a cable tie or put them aside 4.) Measure the position of the fork inner tube inside the fork bridges Measure how far the fork bars jut out from the upper fork bridge then note down the exact amount in the text-box below. The protrude of the fork bars in mm Tip: Both bars should protrude exactly the same distance. 5.1) Loosen the clamping screws of the upper fork bridge 5.2) Release the fork caps for approximately one turn of the thread. 5.3) Loosen the clamping screws of the lower fork bridge. Tip: With some models, the clamping screws must be taken out completely.

2007 Kawasaki ZX6R Full System Installation

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
1. Remove the faring lowers (save STD bolts for reuse) , side faring (save STD bolts for reuse) , seat faring (save front 2 STD bolts for reuse) and right silencer cover. 2. Detach the turn signal assy, (unplug the cable coupler of turn signal and brake light at the same time) 3. Remove the radiator under bracket and lightly unscrew the radiator mounting bolt. Move the radiator forward. This will make you to have enough room for detaching exhaust pipes and flange nuts. Then, take off the standard headpipes. Detach the cable of the exhaust device and l eave servomotor stayed in the motorbody. (save (3) STD bolt and nut and (8) flange nuts for reuse) 4. Assemble the enclosed head pipes 1,2,3 and 4 by matching the 4-2-1 joint. Do not install the exhaust springs at this time. Lightly attach the assembled head pipe sections to the exhaust ports. Make sure the ends of the head pipes fit snug in the ports. 5. Install the tail joint and tail pipe to the joints. Do not install the exhaust springs yet. Jiggle the whole assemble for better fitting. Lightly attach the tail pipe by standard bolt and nut saved in step 3, but do not tighten the bolt fully. (see Image 1) *Recommend to use new gasket to prevent from leaking the exhaust. *Lightly screw the (8) STD flange nuts saved in step 3. * Cylinder number is 1, 2, 3 and 4 from the left hand side with you on the motorbike. 6. Attach enclosed silencer stay A to the place where the standard silencer mounted by (2) STD bolts and nuts saved in step 3. Reinstall the seat faring and penetrate the (2) 5x45mm to the hole of a seat faring mounted. Fix the Silencer stay A by enclosed (2) M5 nuts and (2) aluminum collar using the thread of penetrated M5x45bolts. (see Image 2 and drawing 1) Image 2 7. Insert the TiForce silencer to the tail pipe. Put silencer band and band rubber to the assembled silencer stay A by enclosed (2) M8x20mm bolt and (2) M8 washer. (see drawing 1) 8. Attach the supplied springs to all the joints. Use a spring puller to prevent damage to the springs that could lead to future failure. Put the radiator back to the original position. 9. Attach the L and R license number stay to the silencer stay A. (see Image 3) (see drawing 1) 10. Reinstall the firings detached in step 1. Attach the right silencer cover to the frame by using enclosed faring stay and (1) M6x20mm. (see drawing 1) 11. Make sure the exhaust system is free and clear of the faring. If necessary, adjust for proper clearance.. Removed the fairings reinstalled in step 10. 12. Securely tighten all fasteners in this order (from exhaust pipe flange to silencer stay) Image 3 14. Attach the turn signal assy detached in step 2 to the license number stay. (Use (4) M6x15mm) (See Image 4) Plug the cable couplers.