Installation & Tuning Instructions For all Motorcycle Applications

0

Filed Under (Tips and Review) by admin on 02-01-2012

download
1) Start with a cold motorcycle, and remove the seat (see owners manual for seat removal instructions). 2) Locate a suitable place for your new PowerCard: It is generally velcroed or zip tied under the seat or behind cowling, check for the easiest mounting and wire routing. Often it is easier to place the card in the desired location, and then pull wires from there, rather than connecting the wires and trying to work the PowerCard backward. (In a 2004 Yamaha R6 for example, it is easiest to mount the card, then route connectors one by one through to the engine compartment.) 3) Disconnect the battery ground. Battery may need to be removed to aid in installation (2006 Yamaha R1 for example). 4) Remove the fuel tank and necessary cowlings – many tanks can simply be rotated up and away to allow access to the fuel injector connectors. Secure the tank. Be careful to prevent fuel spills if fuel line removal is necessary – use the quick-disconnect fittings if your motorcycle is so equipped. (see owners manual for tank removal instructions) a. Note: ZX10 installation also requires removal of the stock air box. Unbolt, disconnect fittings, and then turn clock-wise one-quarter turn to remove. Distributed Exclusively by Moss Motors, Ltd.
3 PowerCard┬«Instructions Injector lead #3 improperly installed (+) 2 1 (-) 4 3 Distributed Exclusively by Moss Motors, Ltd. 5) Connecting the PowerCard harness inline: a. Remove any one factory fuel injector connector from an injector (a flat blade screwdriver or long nose pliers may be used to ease removal). b. Couple the female connector from the PowerCard onto the fuel injector, and plug the male connector into the ECU/factory wiring harness. c. Repeat for the rest of the fuel injector connectors – The order is not important as long as they are installed as they are paired (in and out)

Victory LED Brake Light Module Installation

0

Filed Under (Victory) by admin on 31-10-2010

download
Brake Module Installation: Locate the Auto Cancel Module (ACM) under the seat on the right side of the battery box area. Select a suitable location to mount this product near the ACM module. Disconnect negative terminal on battery before installation.. Do not attached attach the product at this time. Setup: Set dip switches according to the chart below. Switch Settings: 1 2 3 4 Result OFF OFF OFF OFF 3 Flashes-Solid-Repeat ON OFF OFF OFF 3 Strobes-Solid-Repeat OFF ON OFF OFF 3 Strobes -Solid ON ON OFF OFF 3 Flashes – Solid OFF OFF ON OFF Variable Flash Rate – Use Pot to adjust flash rate Route and connect the wires as follows: Refer to block diagram on page 2. Locate the White with Pink Tracer wire leading into the ACM module. Cut this wire approximately 2-3 inches from the ACM module. A: Red: Input: Connect this wire to the cut White/Pink wire leading away from the ACM module using supplied posi-tap. (See enclosed instructions for Posi-Tap) B: Yellow: Output: Connect this wire to the cut White/Pink leading into the ACM module using supplied posi-tap. C: Black: Ground: Connect this wire to a good bare metal contact or negative terminal of battery using supplied terminal ring, crimp terminal ring onto black wire, heat terminal ring to form with heat gun or hair dryer until heat shrink, shrinks. Attach the unit to your vehicle using supplied 3M tape or tie wraps. Reconnect negative terminal to battery. Operation: Apply power and check that LED(s) operate correctly in both running light and brake light mode. Caution! This product is designed for use on DC motorcycle applications with negative ground only! This product is not recommended or approved for any other application. Warning! This product is intended to drive high output LEDs ONLY. Do not connect this product’s output to any other type lamp. Maximum output current is 2 amps. Overloading, improper use or improper operation of this product will void the warranty and many damage the product. Warning! Consult your owners’ manual or the vehicle manufacture before installing this or any other electronic product