HARLEY DAVIDSON SPORTSTER CHOPPED FENDER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-03-2011

download
INSTALLATION Preparation 1. Position the vehicle on a motorcycle lift under the frame so the vehicle is upright and level. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the service manual and follow the instructions given to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. 3. Remove the battery from the vehicle per the instructions in the service manual. 4. Raise the rear of the vehicle to relieve the load on the shock absorbers. 5. Follow the service manual instructions to remove only the bottom end shock absorber fasteners on each side of the vehicle. Save the fasteners for later assembly. 6. Raise the rear of the vehicle further to allow access to the underside of the rear fender. 7. Remove the license plate from the vehicle (if installed). Retain the plate and attaching hardware. Rear Fender Removal NOTE Note the location and orientation of rear fender mounting hardware, and save for later assembly. 1. Refer to the service manual and follow the instructions given to remove the rear fender, with the following exceptions: a. Removal of the tail lamp from the fender is not necessary. Rear Lamp Wiring 1. Cut off and discard the socket housings and terminal ends from the turn signal wires. 2. See Figure 1. Unscrew and remove the turn signal stalk (15) from one of the turn signal lamps, and discard. Remove and retain the turn signal lamp and support (14) from the rear fender support cover. 3. Insert the blade of a small screwdriver into the slot at the bottom of the turn signal lamp lens (2), and twist to unsnap the lens from the housing (1)

HARLEY DAVIDSON SOFTAIL FRONT SPOILER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 2 and Table 1. INSTALLATION 1. Position the vehicle on a motorcycle lift table. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 2. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 3. Raise the vehicle on the lift table to allow access to the lower front portion of the frame. 2008+ 2007 7 8 11 3 3 4 4 12 5 5 1 1 9 2 2 10 6 6 9 9 11 13 is02652c 8. 1. Two-pin voltage regulator connector (2007 only) Voltage regulator 2. 9. Voltage regulator attaching screws (2) Cable strap (2 for 2007, 1 for 2008 and later) 10. 3. Lower voltage regulator cover (2007 only) Voltage regulator bracket 4. 11. Bracket screw to engine crankcase (2) Oxygen sensor connector 12. 5. Crank position sensor connector (2007 only) Voltage regulator caddy 6. 13. Voltage regulator caddy cover Horn connectors (some 2008 and later models) 7. Four-pin voltage regulator connector (2007 only) Figure 1. Original Equipment Voltage Regulator  NOTE For 2007 models: The ground wire on the voltage regulator must be re-attached at the original location when re-installing the voltage regulator to ensure adequate ground. 4. For ALL models: See Figure 1. Remove and discard the voltage regulator caddy cover (6) from the regulator bracket (3) and caddy (5). For 2007 models: In addition, remove the lower voltage regulator cover (10). 5. Remove and retain the hex socket head screw (4) at the top left of the bracket For 2007 models: In addition, disconnect the ground wire. Free the cable straps (9) from the regulator bracket, beneath the regulator. 6. Remove the two hex socket head screws with washers (2) retaining the voltage regulator to the bracket. Remove and save the regulator, but discard the screws. 7. Remove and retain the screw (4) at the top right of the regulator bracket. Remove the bracket from the engine. 8. For 2008 and later models: Free the strap (9) that ties the jiffy stand wiring to the voltage regulator bracket. Unfasten the three-way jiffy stand sensor connector and the two-way crank position sensor connector [79] (12) from the T-studs on the back of the regulator bracket (3). Discard the bracket. Disconnect both plugs from the back of the voltage regulator (1). For 2007 models: Unfasten the four-way (7) and two-way (8) voltage regulator connectors from the T-studs on the back of the regulator bracket (3), and discard the bracket. Disconnect the voltage regulator (1) at both connectors. 9. For 2008 and later models: Unclip the two-way O 2 (oxygen) sensor electrical connector [138] (11) from the voltage regulator caddy (5). For 2007 models: Unfasten the two-way crank position sensor connector [79] (12) from the voltage regulator caddy (5). Remove the caddy from the vehicle frame. a. For 2007 models: Unclamp the bottom of the caddy from the engine mount spacers. b. For ALL models: Unhook the top clips from around the tabs on the front of the engine casting. Remove the original equipment (O.E.) caddy from the vehicle frame, and discard it.

Incoming search terms:

HARLEY DAVIDSON LAYBACK LICENSE PLATE AND TURN SIGNAL RELOCATION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 3 2 1 is00851 1. Tail/stop lamp connector 2. Left turn signal connector 3. Right turn signal connector Figure 1. Rear Lamp Connectors 1. Raise the vehicle on a motorcycle lift to allow access to the underside of the rear fender. 2. Refer to the Service Manual and follow the instructions given to remove the negative battery cable (earlier Dyna models) or Maxi® Fuse (all XL’s and later Dyna models). 3. Remove the license plate from the vehicle (if installed). Remove and discard the original equipment license-plate bracket and attaching hardware from the fender. Clean the mounting area on the fender with a soft, damp cloth. 4. See Figure 1. Remove the two screws securing the tail/stop lamp lens assembly, and remove the lens and bulb assembly. Depress the latch on the four-way tail/stop lamp connector (1), and disconnect the connector from the circuit board. 5. Depress the latches on the left-side (2) and right-side (3) two-way turn signal connectors, and disconnect the connectors from the circuit board. 6. Remove the turn signal wires from the retention clips under the fender.

PRO-CYCLE AND PRO-CYCLE XLT 1,000-Lbs. Capacity Motorcycle Lift

0

Filed Under (Tips and Review) by admin on 27-11-2010

download
1. Always inspect the lift for freight damage and make note of any damage on the bill of lading. 2. In case of freight damage, call the truck line immediately and report the damage as a freight claim. Final Set-Up for model Pro-Cycle This lift is more than 90% factory pre-assembled. The following steps will guide you through the final set-up. IT WOULD BE EASIER FOR TWO MEN TO COMPLETE FOLLOWING STEPS. 1. Unpack the lift from the shipping skid. With the lift table up side down, connect the air hose to the air cylinder (Part # 26). 2. After tightening the hose to the cylinder, flip the lift over with the table surface up. 5 3. Lift up the table manually to the first lock position to make sure the lift is rising freely. Lubricateing the joints again before use will ensure a better performance of the lift. 4. Connect the other end of the air hose to the foot-operated valve. Then connect the foot- operated valve to 100 PSI air supply. DO NOT USE AIR SUPPLY WITH PRESSURE MORE THAN 100 PSI. 5. Release the safety bar by pushing the handle down. Operate the foot valve by stepping on the footpad forward to raise the lift. The safety bar should engage the ladder automatically while lift is rising. Step on the footpad again to set the pad in middle position to stop the lift when it reaches the desired height. ALWAYS LOWER LIFT IN THE NEAREST LOCKED POSITION BEFORE BEGINNING WORK. NEVER USE THE LIFT UNLESS YOU ARE IN A LOCKED POSITION. The lift should never be left unattended while attached to air pressure. Disconnect the air pressure when lift is not attended by qualified persons. 6. Install the vise using bolts and nuts supplied with the lift (part # 6 to 12). See fig #1. 7. Install the approach ramp by dropping it into the holes punched on the rear edge of the table. The final Set-Up for the Pro-Cycle model is complete

Incoming search terms:

COMMANDER 1,000 LBS. CAPACITY MOTORCYCLE LIFT INSTALLATION AND OPERATION MANUAL

0

Filed Under (Tips and Review) by admin on 25-11-2010

download
Your lift comes packaged as a single unit. A fork-lift, floor-jack or other heavy-lifting equipment may be necessary to separate the components. Exercise caution when disassembling the packaged lift, as shifting may have occurred during shipping. 2] Carefully unpack the lift. Check for any obvious shipping damage. (Remember to report any shipping damage to the carrier and make a notation on the delivery receipt.) 3] Carefully turn the table upright into operating position before removing shipping cable restraint from scissor mechanism. 4] Connect foot-operated air valve to 100 psi maximum air supply. The lift may be damaged and/or personal injury may result if the pressure exceeds the maximum 100 psi rating. 5] Stand clear of lift table, and depress the “UP” side of the foot valve to raise the table. 6] To lower table, lift locking bar from safety latch and lower to next position, or to the floor. 7] Place drop-out cover over drop out opening. 8] Insert ramp mounting pins into holes at either end of table to mount ramp. NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise. OPERATION and MAINTENANCE 1] Loads must be centered on table at all times. Table is rated for a maximum load of 1,000lbs. 2] Loads must be firmly positioned and secured on table at all times. 3] All moving parts have been lubricated at the factory and should be re-lubricated every six (6) months to prevent problems. Grease points are located at each end of frame pivot shaft and at top ends of inside frame assembly. 4] Lightly oil cylinder rod when it becomes dry. 5] Squirt some oil through bleed hole in plate end of cylinder to lubricate piston and its seal every six (6) months. 6] Pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top end of the inside frame assembly.

BMW K1200GT Backrest Installation MANUAL

0

Filed Under (BMW) by admin on 26-10-2010

download
Remove seat from motorcycle. Place support bracket into opening at the rear of the seat. Start bolts and lock washers thru support bracket into back of seat as shown. Repeat using bolts and washers on the bottom of the seat. Now tighten all 4 bolts. C D E F 2 A B C D E F Factory set screws, Backrest Support bracket 20MM long bolts, qty. 2 Flat washers, qty. 2 16MM long bolts, qty. 2 Lock washers, qty. 2 Check parts included: CYCLE PRODUCTS BMW K1200 GT Backrest Installation Instructions See important warnings and disclaimers on page one. Replace seat onto motorcycle. Lift World Sport logo slot cover and insert backrest A into slot until you hear a click. Now you are ready to go!