Yamaha YZF-R1 Undertail Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-01-2012

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting. 2) Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos above and below. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary. 3) Now relocate the rear mounting holes for the glove box 1.25″ lower in the tray to raise it up in the subframe as shown. Yamaha YZF-R1 Undertail Kit (2000-01, Available in: Yamaha Red, Yamaha Blue) Need Help? If you need additional help with the installation of the undertail, go to www.hotbodiesracing.com and look for the “FAQs” link at the bottom of the home page. Most of your general questions can be answered on those pages. This installation does require a basic mechanical aptitude, if in doubt, contact your local motorcycle shop and have a professional mechanic perform the installation, 3 hours is the average installation time. * After this modification your undertail is not returnable. Paint is not war- rantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray. 5) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts

VT 1100 TEARDROP SPECIFIC-FIT SADDLEBAGS INSTALLATION

0

Filed Under (Honda) by admin on 23-11-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets

Honda VT1100C Shadow, Aero, Sabre SPECIFIC-FIT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets TIP: Use soapy water to lubricate the grommets so they will slip into the holes in the bag. The vehicle images in this instruction set may be different than your motorcycle. Continued on next page… 3 Lay a support 7 (with the joint towards the rear of the bag) on the back of a bag. Temporarily put the mounting bolts 8 through the support’s holes and into the plas- tic spacers in the grommets. Place one of the support clips 9 over the center of the lower portion of the support, so the two holes in the clip align with the predrilled holes in the bag. Use the 3/16” screws and nuts from the hardware kit to attach the support clip to the backup plate inside the bag. Place the nuts on the outside of the bag. Do not over- tighten the hardware, as this may cause damage to the saddlebag. Remove the mounting bolts from the support and the plastic spacers

Incoming search terms:

Kawasaki ZX14R Undertail Kit installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
This installation does require a basic mechanical aptitude, if in doubt, contact your local motorcycle shop and have a professional mechanic perform the installation, 1.5 hours is the average installation time. 7) Use supplied pop rivets to mount the undertail over top of the stock black trunk compartment and complete wiring of the LED license plate light. To connect the license plate light; use the stock black and yellow tracer wires with black undertail wire and stock red with red undertail wire. 6) Before installing the undertail, remove the adhesive back. Carefully clean the stock part where this adhesive will apply to. After you install the undertail with the rivets, press firmly and hold for 30 seconds. 8) After mounting undertail, re-install ECU and tool compartments. After re-installation of tool compartment re-install seat and seat cover, making sure all bolts and hardware are fastened securely. Your done! * After this modification your undertail is not returnable. Paint is not war- rantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray.